Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations Mike Lewis on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

IP office 11.1.2.0.0 build 239 Can not forward call using unconditional forward

Status
Not open for further replies.
JimFed

JimFed

IS-IT--Management
Mar 26, 2020
43
US
System has a PRI. Setup a virtual extension and a user assigned to this extension. Routed DID to that user but call will not forward it goes to Voice mail immediately. Setup new virtual extension and new user and the same results. Rebooted system as well. All calls go directly to voicemail and are not forwarded to users cell. System status just shows going directly to voice mail. Inhibit off switch transfer is not checked. I do this all the time with SIP trunks and it works. Customer is using twining for many users and that works. Tried using twinning and selected the option twin when logged out and this also does not work. Goes directly to voicemail. If I disable voicemail I get a busy signal.
I have spent tons of time on this. This should be easy. Thanks for any help
 
Sort by date Sort by votes
Don’t forget you have to uncheck inhibit off switch transfer in User and System
You also need the short code for calling out in system short code

What happens when you ring the user directly..
Does it forward out to cell phone
 
Upvote 0 Downvote
Checked both system and user and the inhibit off switch transfer is not checked. We put 9 and the number for dialing out. I also added a user short code that is 9N and ars table 50:main
Still goes directly to voice mail
 
Upvote 0 Downvote
13:35:10 8750106mS PRN: Q931Trunk: Found QBChannel to match 0.2 --> 7.3
13:35:10 8750106mS CMCallEvt: 0000000000000000 0.536872313.0 -1 BaseEP: NEW CMEndpoint f17cd5f4 TOTAL NOW=5 CALL_LIST=2
13:35:10 8750106mS CMTARGET: ISDN BChannel 2: in-service check = 1
13:35:10 8750107mS CMCallEvt: CREATE CALL:103 (f17f42cc)
13:35:10 8750107mS CMCallEvt: 0000000000000000 0.536872314.0 -1 BaseEP: NEW CMEndpoint f17f2428 TOTAL NOW=6 CALL_LIST=2
13:35:10 8750110mS CMCallEvt: 0a0000f920000579 13.6.1 103 Q931 Trunk:13 CHAN=2: StateChange: END=A CMCSIdle->CMCSDialInitiated
13:35:10 8750110mS CMTARGET: 0a0000f920000579 13.6.1 103 Q931 Trunk:13 CHAN=2: LOOKUP CALL ROUTE: GID=0 type=0 called_party=5592562383 sub= calling=5592245922 calling_sub= dir=in complete=1 ses=0
13:35:10 8750111mS CMTARGET: 0a0000f920000579 13.6.1 103 Q931 Trunk:13 CHAN=2: SET BESTMATCH: length 0 vs -1 match= dest=Operator climatch -1 vs -1
13:35:10 8750111mS CMTARGET: 0a0000f920000579 13.6.1 103 Q931 Trunk:13 CHAN=2: SET BESTMATCH: length 4 vs 0 match=2383 dest=2900 climatch -1 vs -1
13:35:10 8750111mS CMCallEvt: Priority hike: call 103 priority 0->1
13:35:10 8750111mS CMTARGET: 0a0000f920000579 13.6.1 103 Q931 Trunk:13 CHAN=2: LOOKUP ICR: DDI= CGPN=5592245922 (Destination 2900 CLI ) => CDPN=2900
13:35:10 8750112mS CMTARGET: 0a0000f920000579 13.6.1 103 Q931 Trunk:13 CHAN=2: ADD TARGET (N): number=2900 type=0 depth=1 nobar=1 setorig=1 ses=0
13:35:10 8750112mS CMTARGET: 0a0000f920000579 13.6.1 103 Q931 Trunk:13 CHAN=2: SET USER: ForwardTest orig=1
13:35:10 8750112mS CMTARGET: 0a0000f920000579 13.6.1 103 Q931 Trunk:13 CHAN=2: ADD USER: ForwardTest depth=1 disallow_cw=0 dnd=0 real_call=1 group_call=0 type(CMNTypeUnknown) incl(0x0) excpt(0x0), allow_redir(1) remote=00000000 simult 0 (0) r_lic=
T
13:35:10 8750113mS CMTARGET: TryLoggedOutTargeting for user ForwardTest Failed Normal
13:35:10 8750113mS CMTARGET: FoundKnownSystemTargets ICR cache hit
13:35:10 8750113mS CMTARGET: 0a0000f920000579 13.6.1 103 Q931 Trunk:13 CHAN=2: NO INITIAL TARGETS: ForwardTest
13:35:10 8750113mS CMTARGET: 0a0000f920000579 13.6.1 103 Q931 Trunk:13 CHAN=2: ADD USER: ForwardTest depth=1 disallow_cw=0 dnd=0 real_call=1 group_call=0 type(CMNTypeUnknown) incl(0x40) excpt(0x40), allow_redir(1) remote=00000000 simult 0 (0) r_li
c=T
13:35:10 8750114mS CMTARGET: TryLoggedOutTargeting for user ForwardTest Failed Normal
13:35:10 8750114mS CMTARGET: 0a0000f920000579 13.6.1 103 Q931 Trunk:13 CHAN=2: SELECT: TRY VOICEMAIL orig_hg() orig_user(2900)
13:35:10 8750114mS CMTARGET: 0a0000f920000579 13.6.1 103 Q931 Trunk:13 CHAN=2: ADD VM TARGET
13:35:10 8750114mS CMTARGET: 0a0000f920000579 13.6.1 103 Q931 Trunk:13 CHAN=2: MakeVoicemailTarget pbx=<null> local=1 type=1
13:35:10 8750115mS CMCallEvt: 0000000000000000 0.536872315.0 -1 BaseEP: NEW CMEndpoint f17c0af0 TOTAL NOW=7 CALL_LIST=3
13:35:10 8750115mS CMTARGET: 0a0000f92000057b 0.536872315.0 103 RAS.0: ADD PRIMARY
13:35:10 8750115mS CMTARGET: 0a0000f920000579 13.6.1 103 Q931 Trunk:13 CHAN=2: ADD VM TARGET: SUCCEEDED
13:35:10 8750115mS CMTARGET: 0a0000f920000579 13.6.1 103 Q931 Trunk:13 CHAN=2: GetNoAnswerTimer:20
13:35:10 8750116mS CMCallEvt: 0a0000f920000579 13.6.1 103 Q931 Trunk:13 CHAN=2: StateChange: END=A CMCSDialInitiated->CMCSDialled
13:35:10 8750116mS CMLineTx: v=13
CMProceeding
Line: type=Q931Line 13 Call: lid=13 id=6 in=1
BChan: slot=0 chan=2
13:35:10 8750116mS CMCallEvt: 0000000000000000 0.536872314.0 103 TargetingEP: StateChange: END=B CMCSIdle->CMCSOffering
13:35:10 8750117mS CMCallEvt: 0a0000f92000057b 0.536872315.0 103 RAS.0: StateChange: END=T CMCSIdle->CMCSOffering
13:35:10 8750117mS CMExtnEvt: RAS: CMExtnHandler::SetCurrent( id: 0->536872315 )
13:35:10 8750118mS CMExtnTx: v=RAS, p1=0
CMSetup
Line: type=RAS 1 Call: lid=0 id=1011 in=0
Called[#ForwardTest] Type=Voicemail (102) Reason=107 SndComp Calling[5592245922] Type=Unknown Plan=ISDN Pres=Allowed (0)
BC: CMTC=Speech CMTM=CallIndSigCon CMTR=64 CMST=Default CMU1=ULaw
BChan: slot=21 chan=42
IE CMIESupplementaryService (3)
Interpretation APDU
rejectAnyUnrecognisedInvokePdu
CallingName.Invoke.CodePageISO8859-1
invokeId 1
user 'Jim' presentation Allowed
IE CMIECallingPartyName (110)(Type=CMNameDefault) name=Jim
IE CMIECalledPartyName (224)(Type=CMNameInternalUser) name=ForwardTest
IE CMIECalledPartyKName (225)(Type=CMNameDefault) name=ForwardTest
IE CMIERespondingPartyName (228)(Type=CMNameDefault) name=Jim
IE CMIERespondingPartyNumber (230)(P:0 S:0 T:0 N:1 R:4) number=5592245922
IE CMIEDeviceDetail (231) 0a0000f920000579 LOCALE=enu HW=15 VER=11 class=CMDeviceISDNTrunk type=2 number=13 channel=2 features=0x20 rx_gain=32 tx_gain=32
ep_callid=536872313 ipaddr=10.0.0.249 apps=0 loc=0 em_a_loc=0 em_d_loc=0 features2=0x0 is_spcall=1 ignores_dtmf=0
avgsid=<>
IE CMIERedirectingPartyName (232)(Type=CMNameInternalUser) name=ForwardTest
IE CMIERedirectingPartyKName (233)(Type=CMNameDefault) name=ForwardTest
IE CMIERedirectingPartyNumber (234)(P:100 S:100 T:101 N:100 R:2) number=2900
IE CMIEOriginalCalledPartyName (236)(Type=CMNameInternalUser) name=ForwardTest
IE CMIEOriginalCalledPartyKName (237)(Type=CMNameDefault) name=ForwardTest
IE CMIEOriginalCalledPartyNumber (238)(P:100 S:100 T:101 N:100 R:2) number=2900
IE CMIEIcrPriorityDetail (239) Priority = 1
IE CMIEDIDNumber (245)(P:100 S:100 T:0 N:1 R:4) number=5592562383
IE CMIEMohSourceId (247) MOH Source = 1
Display [Jim>ForwardTest]
Timed: 14/07/22 13:35
Locale: enu
13:35:10 8750118mS CMMap: a=21.42 b=1.65534 T
13:35:10 8750120mS CMExtnRx: v=RAS, p1=0
CMAlerting
Line: type=NoLine 0 Call: lid=0 id=-1 in=0
IE CMIERespondingPartyName (228)(Type=CMName_VMPro) name=#ForwardTest
IE CMIERespondingPartyNumber (230)(P:100 S:100 T:102 N:100 R:4) number=#ForwardTest
IE CMIEDeviceDetail (231) 0a0000f92000057b LOCALE=enu HW=15 VER=11 class=CMDeviceVoicemail type=0 number=0 channel=42 features=0x0 rx_gain=32 tx_gain=32
ep_callid=536872315 ipaddr=10.0.0.249 apps=0 loc=0 em_a_loc=0 em_d_loc=0 features2=0x0 is_spcall=0 ignores_dtmf=0
avgsid=<>
IE CMIERedirectingPartyName (232)(Type=CMNameInternalUser) name=ForwardTest
IE CMIERedirectingPartyKName (233)(Type=CMNameDefault) name=ForwardTest
IE CMIERedirectingPartyNumber (234)(P:100 S:100 T:101 N:100 R:2) number=2900
13:35:10 8750121mS CMCallEvt: 0a0000f92000057b 0.536872315.0 103 RAS.0: StateChange: END=T CMCSOffering->CMCSRinging
13:35:10 8750121mS CMExtnEvt: v=1011 State, new=Ringing old=Idle,0,0,RAS
13:35:10 8750121mS CMTARGET: 0a0000f920000579 13.6.1 103 Q931 Trunk:13 CHAN=2: CancelTimer CMTCNoAnswerTimeout
13:35:10 8750121mS CMCallEvt: 0000000000000000 0.536872314.0 103 TargetingEP: StateChange: END=B CMCSOffering->CMCSRinging
13:35:10 8750121mS CMCallEvt: 0a0000f920000579 13.6.1 103 Q931 Trunk:13 CHAN=2: StateChange: END=A CMCSDialled->CMCSRingBack
13:35:10 8750122mS CMLineTx: v=13
CMAlerting
Line: type=Q931Line 13 Call: lid=13 id=6 in=1
BChan: slot=0 chan=2
13:35:10 8750125mS ISDNL3Evt: v=13 stacknum=13 State, new=ICProceeding, old=Present id=6
13:35:10 8750126mS ISDNL3Evt: v=13 stacknum=13 State, new=Received, old=ICProceeding id=6
13:35:10 8750126mS CMMap: a=7.3 b=0.0 R1
13:35:10 8750131mS RES: Thu 14/7/2022 13:35:09 FreeMem=51951004 Heap=51330388(2) Cache=620616 MemObjs=21006(Max 22562) CMMsg=8(9) ASN=0 Buff=5200 1371 1000 7356 5 Links=61802(62007) BTree=1803(4091) CB=6061 MCT=0 CPU=07.50% CPUStats=13.25%/18/5/821/12
620/14507/00.82%/0/03.66% MCR=0 MCW=0 DEV=0
13:35:10 8750131mS RES2: IP 500 V2 11.1.2.0.0 build 239 Tasks=61 RTEngine=2 CMRTEngine=0 ExRTEngine=0 Timer=12+133 Poll=0 Ready=0 CMReady=0 CMQueue=0 VPNNQueue=0 Monitor=1 SSA=1 TCP=58(TLS=7 OFF=0) TAPI=1 Partner=123 ASC=1 SYS=MNTD OPT=UMNT SDSPD=2034
13:35:10 8750131mS RES4: XML MemObjs=8 PoolMem=4748404(2) FreeMem=4736284(0) HeapUsed=0
13:35:10 8750132mS RES5: CLog MemObjs=1606 FreePoolMem(Objs)=5264(94) TotalMem=95200 StringsTotalMem=136500
13:35:10 8750233mS CMExtnRx: v=RAS, p1=0
CMVoiceMailMsg
Line: type=NoLine 0 Call: lid=0 id=-1 in=0
Called[LeaveMessage] Type=Default (100) Reason=CMDRdirect Calling SubAddress[0]
Tag type=Text flags=0x1 [1.] [0x31 0x00 ]
13:35:10 8750233mS CMCallEvt: 0000000000000000 0.1001.0 -1 BaseEP CMEndpoint does nothing with msg - 38 CMVoiceMailMsg
 
Upvote 0 Downvote
Here is my last call. I setup a new forwardtest user and new extension for this test as well.

This last call was setup using mobility features. I have a power user license assigned. I have also tried using unconditional forward.
Always rings twice and then goes to voice mail
 
Upvote 0 Downvote
Does the carrier need to have this enabled on the PRI?
Take it in steps...
First try calling the external 10-digit telephone number that you are call forwarding to and do this from any extension on the system - what are the results?
Then try dialing internally the virtual extension that you built with call forwarding enabled to the same number - what are the results?
Disable UCFW, and enable mobile twinning with the same phone number (check the box twin when logged out), call the extension internally - what are the results?


APSS-Midmarket
ACIS-Midmarket
ACSS-Midmarket
ACDS-Midmarket
 
Upvote 0 Downvote
If I recall correctly, a user will not forward calls if logged out (virtual user). You need to use mobile twinning instead, with "twin when logged out" enabled. I also enable "Fallback Twinning" for good measure too.

twinning_e4tcq4.png


“Some humans would do anything to see if it was possible to do it.
If you put a large switch in some cave somewhere, with a sign on it saying 'End-of-the-World Switch. PLEASE DO NOT TOUCH'.
The paint wouldn't even have time to dry.”

Terry Pratchet
 
Upvote 0 Downvote
I opened ticket with Avaya and they looked at the settings and said it is all setup correctly. They told me to upgrade to latest service pack before they will look at it any further
I think there is a bug with virtual extensions. I bet that if I log a phone in with that extension it would work as lots of users are using twinning with out any issues

I will upgrade over the weekend and see what happens
 
Upvote 0 Downvote
Try the Fallback twinning, I have had a similar situation where users do not have a phone or workplace and use mobile twinning, ticking this got them working.

“Some humans would do anything to see if it was possible to do it.
If you put a large switch in some cave somewhere, with a sign on it saying 'End-of-the-World Switch. PLEASE DO NOT TOUCH'.
The paint wouldn't even have time to dry.”

Terry Pratchet
 
Upvote 0 Downvote
There is a bug, in that, if you use the drop-down selection to assign destinations (like on incoming call routes), they don't work. If this is true in your case, try typing in the destination instead of using the drop-down.

Please remember... If it's not the way that YOU would do it, that does not necessarily mean it's wrong. EVERYONE knows SOMETHING that you do not.
 
Upvote 0 Downvote
The twinning settings above solution did work after I took out the 559 area code from the twinned number. I then tried the same number of forward unconditionally and it works as well. I also had to add the 9 and the seven digit number for it to work. I tried no 9 and 10 digit number as well as just 7 digit number but not the 9 and 7 digit number which was the fix.
Telfire was correct as 10 digit dialing did not work. Weird as we usually put the 10 digit number in and it works fine. This customer has a AT&T ip flex PRI and I guess it does not work. Thanks for all the help everyone. Did not put the service pack in yet so that had nothing to with the problem
 
Upvote 0 Downvote
Status
Not open for further replies.

Similar threads

daken
  • Locked
  • News
PSN006301u - IP Office 12.0.0.0 Build 55 replaced with IP Office 12.0.0.0 Build 56 2
Replies
2
Views
157
IamaSherpa
IamaSherpa
T
  • Locked
  • Question
IP Office R11.0.4.8.0 build 17 Cannot get Workplace to register.
Replies
15
Views
692
telecomtekperson
T
M
  • Locked
  • Question
Avaya IP Office - Unable to call specific number 1
Replies
13
Views
978
mike Wazowski
M
D
  • Question
AVAYA IP Office R12 using Softconsole for Operator 1
Replies
15
Views
1K
dave_jey2004
D
digital12188
  • Locked
  • Question
IP Office SE 11.1 SP3 with Enghouse/Zeacom Call center
Replies
1
Views
224
derfloh
derfloh

Part and Inventory Search

Sponsor

Back
Top