bkelly1676
Technical User
i have been getting the following errors
"SRPT4619 WARNING: Last Archive Procedure had failed
No archives were completed since Apr 11 00:04:00 2007
Use LD 143 to perform Attended Backup(ABKO)"
i did the following tests and the book states that i need to replace the IOP/CMDU card
">ld 137
CIOD000
.test iop
CIOD033 The active IOP needs to be disabled
.test cmdu 1
OK: CMDU 1 HDK
CIOD008 1: CMDU 1 FDK test fail
.test cmdu 1
OK: CMDU 1 HDK
CIOD008 1: CMDU 1 FDK test fail
.test cmdu 1
OK: CMDU 1 HDK
CIOD008 1: CMDU 1 FDK test fail"
i know i need to replace the card and i have one that is the same release as the bad card but want to be sure that i am following the correct procedure. i looked in the NTPs and am a little confused so i was hoping somebody could let me know if the procedures i got from the previous tech are OK. the following is the procedure i was given.
IOP / CMDU SWAP
Step 1: LD 43 – EDD
Step 2: Take floppy out of IOP / CMDU your replacing
Step 3: Verify that running IOP is not the one you are changing
Step 4: Software disable IOP / CMDU LD 137 – DIS CMDU x
Step 5: Hardware disable IOP / CMDU
Step 6: Remove disabled IOP / CMDU card
Step 7: Remove program cartridge from old IOP / CMDU card and place in new card
Step 8: Insert new IOP / CMDU card
Step 9: Hardware enable new IOP / CMDU
Step 10: Test CMDU = LD 137 – TEST CMDU x
Step 11: Test CMDU Hard Disk = LD 137 – TEST CMDU x HDK
Step 12: Insert disks back into new CMDU
Step 13: Test CMDU Floppy Disk = LD 137 – TEST CMDU x FDK
Step 14: Data Test CMDU = LD 137 – DATA - CMDU x
Step 15: Data Test CMDU Hard Disk = LD 137 – CMDU x HDK
Step 16: Data Test CMDU Floppy = LD 137 – CMDU x FDK
Step 17: Synchronize the hard disks = LD 137 – SYNC
Step 18: Test redundancy = LD 137 – TEST RDUN
Step 19: Verify redundancy = LD 137 – DATA RDUN
Step 20: Software Enable CMDU = LD 137 – ENL CMDU x
Step 21: Swap Running CMDU = LD 137 – SWAP
thanks all
"SRPT4619 WARNING: Last Archive Procedure had failed
No archives were completed since Apr 11 00:04:00 2007
Use LD 143 to perform Attended Backup(ABKO)"
i did the following tests and the book states that i need to replace the IOP/CMDU card
">ld 137
CIOD000
.test iop
CIOD033 The active IOP needs to be disabled
.test cmdu 1
OK: CMDU 1 HDK
CIOD008 1: CMDU 1 FDK test fail
.test cmdu 1
OK: CMDU 1 HDK
CIOD008 1: CMDU 1 FDK test fail
.test cmdu 1
OK: CMDU 1 HDK
CIOD008 1: CMDU 1 FDK test fail"
i know i need to replace the card and i have one that is the same release as the bad card but want to be sure that i am following the correct procedure. i looked in the NTPs and am a little confused so i was hoping somebody could let me know if the procedures i got from the previous tech are OK. the following is the procedure i was given.
IOP / CMDU SWAP
Step 1: LD 43 – EDD
Step 2: Take floppy out of IOP / CMDU your replacing
Step 3: Verify that running IOP is not the one you are changing
Step 4: Software disable IOP / CMDU LD 137 – DIS CMDU x
Step 5: Hardware disable IOP / CMDU
Step 6: Remove disabled IOP / CMDU card
Step 7: Remove program cartridge from old IOP / CMDU card and place in new card
Step 8: Insert new IOP / CMDU card
Step 9: Hardware enable new IOP / CMDU
Step 10: Test CMDU = LD 137 – TEST CMDU x
Step 11: Test CMDU Hard Disk = LD 137 – TEST CMDU x HDK
Step 12: Insert disks back into new CMDU
Step 13: Test CMDU Floppy Disk = LD 137 – TEST CMDU x FDK
Step 14: Data Test CMDU = LD 137 – DATA - CMDU x
Step 15: Data Test CMDU Hard Disk = LD 137 – CMDU x HDK
Step 16: Data Test CMDU Floppy = LD 137 – CMDU x FDK
Step 17: Synchronize the hard disks = LD 137 – SYNC
Step 18: Test redundancy = LD 137 – TEST RDUN
Step 19: Verify redundancy = LD 137 – DATA RDUN
Step 20: Software Enable CMDU = LD 137 – ENL CMDU x
Step 21: Swap Running CMDU = LD 137 – SWAP
thanks all