Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

  • Congratulations Mike Lewis on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Incompatible Bandwith 2

Status
Not open for further replies.

aau2

Technical User
Nov 12, 2004
163
ES
Hi, we have connected a pri to cisco router in our CM 5.1, when recieve data calls from other Port Network it fails with denial event 1025 incompatible bandwith, but if it recieves the data call form the same Port Network it works.
From other Port Network

08:56:38 dial 19059 route:UDP|AAR
08:56:38 denial event 1025: Incompatable Bandwidth D1=0x500f0 D2=0x830047
08:56:38 term trunk-group 71 cid 0x2e16
08:56:38 route-pattern 171 preference 1 unavailable cid 0x2e16
08:56:38 denial event 1013: Destination Unavailable D1=0x830001 D2=0x2e16
08:56:38 dial 19059 route:UDP|AAR
08:56:38 term trunk-group 71 cid 0x2e16
08:56:38 denial event 2379: Deny CLR IGC, no admin D1=0x1004a00 D2=0x1
08:56:38 denial event 2379: Deny CLR IGC, no admin D1=0x1004a00 D2=0x1
08:56:38 denial event 2330: No BW, prowler <--> prowl D1=0x1 D2=0x1

I tried to chenge the ip-codec-set and the types of modems of the network region. I think that the problem is when the data call is transformed from tdm to ip.

Any help????


Thanks
 

Looks like a codec mismatch to me..
1025 Incompatable Bandwidth Terminated to an endpoint or trunk group that cannot support the requested bandwidth.

1013 Destination Unavailable Facilities were exhausted during rerouting. Bearer capability is not VOICE, VOICE BAND DATA.
No outgoing trunk queuing, or no trunks, or DEXT, orAdjunct origination, or Administered Connection,or QSIG Call Completion Ringout attempt.
Queueing is not allowed.

2379 Cannot build CLEAR IGC Cannot build CLEAR IGC because clear channel is OFF in the codec set (page 2).(codec Set #used for the IGC)

2330 No BW, prowler <--> prowler No bandwidth channel resources between processors.
 
Hi telcoguy.
The ip-codec are.



IP Codec Set

Codec Set: 1

Audio Silence Frames Packet
Codec Suppression Per Pkt Size(ms)
1: G.711MU n 2 20
2: G.711A n 2 20
3:
4:
5:
6:
7:



IP Codec Set

Allow Direct-IP Multimedia? n



Mode Redundancy
FAX off 0
Modem pass-through 0
TDD/TTY US 3
Clear-channel n 0



 
try adding g729a &u into the equasion, or indeed reaserch what codec the cisco utilises and reflect that setting in your codec set. As although G711 is pri quality you may be getting a mismatch.You could also try wireshark to sniff what the cisco is using.

APSS (SME)
ACSS (SME)
ACIS (UC)
 
The cirsco routeer is connected through one Pri (E1), the fails only is when the call is incoming from other gateway
 
Hi

I had the same, changing clear channel to yes cured this immediately on the codec settings.
 
Status
Not open for further replies.

Part and Inventory Search

Sponsor

Back
Top