Incoming Call not coming..pls see the trace

[JAAGB]

Hi all,
I am tring to install the option 11 mini... the incoming call not landing..pls see the trace and suject us...the 30 Channels are showing idel. The DCH was up msdl aslo up. i am taking the clock from the other end(means i am user)

CH 11 UIPE_IMSG CC_SETUP_IND REF 00005620 CH 1 23 TOD 15:46:22 CK 3753C330
CALLING #:799995541 NUM PLAN: E164 TON: NATL
CALLED #:799947500 NUM PLAN: E164 TON: NATL

DCH 11 UIPE_OMSG CC_REJECT_REQ REF 0000D620 CH 1 23 TOD 15:46:22 CK 3753C354

CAUSE: #42 - SWED EQIP CONGESTION

 

[acewarlock]

How many digits are your ext's?

How many digits is the Telco sending?

 

[JAAGB]

i Have 5 digits extensiom(4XXXX) but the telco was sending(79994XXXX)..but i made in IDC table for that...even thoo its happening

 

[dlesap]

Show us IDC table and RDB config of Opt11 Mini

 

[johnpoole]

SWED EQIP CONGESTION
that seems to say those 30 channels are not the cause.. are you using isa trunks?

john poole
bellsouth business
columbia,sc

 

[JAAGB]

Please see the RDB on Option 11 Mini


TYPE RDB
CUST 00
DMOD 9
ROUT 9
DES PRI
TKTP TIE
NPID_TBL_NUM 0
ESN NO
RPA NO
CNVT NO
SAT NO
RCLS EXT
VTRK NO
DTRK YES
BRIP NO
DGTP PRI2
ISDN YES
MODE PRA
IFC EURO
CNTY ETSI
SBN NO
PNI 00000
NCNA NO
NCRD NO
CTYP INTL
INAC NO
ISAR NO
CPFXS YES
SDID NO
DAPC NO
INTC NO
DSEL VOD
PTYP DTT
AUTO NO
DNIS NO
DCDR NO
ICOG IAO
SRCH LIN
TRMB YES
STEP
ACOD 9
TCPP NO
TARG 01
BILN NO
OABS
INST
IDC YES
DCNO 0
NDNO 0 *
DEXT NO
DNAM NO
SIGO STD
MFC NO
ICIS YES
OGIS YES
TIMR ICF 512
OGF 512
EOD 13952
NRD 10112
DDL 70
ODT 4096
RGV 640
GTO 896


PAGE 002

GTI 896
SFB 3
NBS 2048
NBL 4096

IENB 5
TFD 0
VSS 0
VGD 6
DTD NO
SCDT NO
2 DT NO
DRNG YES
NDRI 00
CDR NO
NATL YES Qrec--yes
SSL
CFWR NO
IDOP NO
VRAT NO
MUS NO
PANS YES
FRL 0 0
FRL 1 1
FRL 2 2
FRL 3 3
FRL 4 4
FRL 5 0
FRL 6 0
FRL 7 0
OHQ NO
OHQT 00
CBQ NO
AUTH NO
TTBL 0
ATAN NO
PLEV 2
OPR NO
ALRM NO
ART 0
PECL NO
DCTI 0
TIDY 9 9
SGRP 0
AACR NO


I made a test IDC table "0" for one number

DCNO 0

SDID NO
IDGT CDGT
799947500 47500

 

[dlesap]

Are you connected to PSTN with that PRI?

Why is it configured as TIE trunk? Might be DID
Why is it configured as EURO ETSI? Might be EURO + country specify

If connected to another PBX, check if both protocols are the same. If connected to Nortel, check PNI value.

Also give DCH configuration...

 

[JAAGB]

I tried with DID and TIE..because my excesting system was working with TIE.Please see the below DID with RDB and DCH



TYPE RDB
CUST 00
DMOD
ROUT 9
DES PRI
TKTP DID
NPID_TBL_NUM 0
SAT NO
RCLS EXT
VTRK NO
DTRK YES
BRIP NO
DGTP PRI2
ISDN YES
MODE PRA
IFC EURO
CNTY ETSI
SBN NO
PNI 00000
NCNA NO
NCRD NO
ISAR NO
CPFXS YES
SDID NO
DAPC NO
INTC NO
DSEL VOD
PTYP DCO
AUTO NO
DNIS NO
DCDR NO
ICOG IAO
RANX NO
SRCH LIN
TRMB YES
STEP
ACOD 9
TCPP NO
TARG 01
BILN NO
OABS
INST
IDC NO
DCNO 0 *
NDNO 0
DEXT NO
MFC NO
ICIS YES
OGIS YES
TIMR ICF 512
OGF 512
EOD 13952
NRD 10112
DDL 70
ODT 4096
RGV 640
FLH 510
GTO 896
GTI 896
SFB 3
NBS 2048
NBL 4096



PAGE 002

IENB 5
VSS 0
VGD 6
DTD NO
SCDT NO
2 DT NO
DDO NO
DRNG NO
CDR NO
NATL YES
SSL
CFWR NO
IDOP NO
VRAT NO
MUS NO
MR NO
PANS YES
EQAR NO
FRL 0 0
FRL 1 0
FRL 2 0
FRL 3 0
FRL 4 0
FRL 5 0
FRL 6 0
FRL 7 0
OHQ NO
OHQT 00
TTBL 0
ATAN NO
PLEV 2
OPR NO
PRDL NO
EOS NO
DNSZ 0
RCAL NO
MCTS NO
ALRM NO
BTT 30
ACKW NO
ART 0
PECL NO
DCTI 0
TIDY 529 9
SGRP 0
AACR NO


Trunks


DES PRI
TN 001 01
TYPE DID
CDEN SD
CUST 0
TRK PRI2
PDCA 1
PCML A
NCOS 0
RTMB 9 1
B-CHANNEL SIGNALING
NITE
AST NO
IAPG 0
CLS UNR DIP WTA LPR APN THFD
P10 VNL
TKID
DTCR NO
DATE 28 MAY 2006


DCH

ENL NO
ADAN DCH 11
CTYP MSDL
CARD 01
PORT 1
DES PRI
USR PRI
DCHL 1
OTBF 32
PARM RS422 DTE
DRAT 64KC
CLOK EXT
IFC EURO
CNTY ETSI
PINX_CUST 0
ISDN_MCNT 300
CLID OPT1
PROG NCHG
CO_TYPE STD
SIDE USR
CNEG 2
RLS ID **
RCAP COLP
MBGA NO
OVLR NO
OVLS NO
T310 120
INC_T306 0
OUT_T306 30
T200 3
T203 10
N200 3
N201 260
K 7

REQ

 

[JAAGB]

This PRI was connected to the telco(provider) not ant other PABX

 

[3Sixty]

What way is the system set up at present?

If it is setup as above you need to set the IDC to yes and set the DCNO and NDNO to 1. Then in LD 49 you would need to create a new IDC (1 in the case above) In LD 49 you would create the Incoming digit (DDI form network) and the number or extension you want to send too.

Marshall

http://www.nortelsupport.net

 

[dlesap]

1- IDC Table 0 can be used as well as IDC 1. It doesn't matter but IDC prompt in RDB must be turn to YES.
IDC YES
DCNO 0 *
NDNO 0

2- RDB must be DID cause connected to provider.
TKTP DID

 

[JAAGB]

The Link was working fine with the BCM...we tested with the BCM incoming and out going was working fine..pls tell me where could be the problem??

 

[captain99]

If you are receiving 9 digits from the main exchange then you must set the ldn in ld 15 to have a number containg the same number of digits eg

ldno 888888888