Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

  • Congratulations SkipVought on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

how to configure ACD# to an external # when called from externally

Status
Not open for further replies.

82736

IS-IT--Management
Jul 21, 2005
7
0
0
US
I have Nortel Meridian Systems Option 61c

I have created an ACD # and foward it to an external number but when someone calls from the outside it goes to the operator.
what am I missing?
 
LD 15, in your RDR block make sure you have CFF in the OPT. It's most likely set for CFO

OLD ROLMEN WORKING ON NORTELS
 
Okay, what are the commands I have gone to ld 15 rdr and on opt I put in cff then what? I'm not sure what to then
 
Have you tested since doing that? Still going to operator?

Mato' Was'aka
 
your acd is maxp 1 ncfw with ac1 in front of it right?
9,xxxxxxx

Mato' Was'aka
 
When you setup the ACD, on the NCFW did you do 9xxxxxxxxx or did you use the Access code to the route you wanted to send the call out on?

I use the Access code and the number and I don't have any problems.




This is a Signature and not part of the answer, it appears on every reply.

This is an Analogy so don't take it personally as some have.

Why change the engine if all you need is to change the spark plugs.


 
this the way I did it

ld 23
new
acd
acdn 1860
maxp 1
ncfw 91866####

then I just took the defaults.

 
take look at these items

EXTT (NO) YES (Prevent) Allow unconditional external Trunk to Trunk transfer.
Enter YES to indicate that a caller can transfer a call made to
one outgoing trunk to another outgoing trunk without restrictions
based on supervision. Trunk to trunk connection features such
as TGAR/TARG and Trunk Barring still apply as appropriate.
Enter NO to indicate that the transfer is allowed only if conditions
regarding supervision are met. This prompt only applies to
situations involving two calls originated by the same caller.
FTOP (FRES)
TBFT FTTB
FTLY
Flexible Trunk to Trunk Connection Option


EXTERNAL XFER
A couple of things to look at in the CDB.
Net Data - TRNX-YES
EXTT-YES

RDR Data - CFF (not CFO)
FTR Data - CFF

Mato' Was'aka
 
Try usin the Access code instead of the 9.

ncfw 91866####
ncfw xxxx1866####





This is a Signature and not part of the answer, it appears on every reply.

This is an Analogy so don't take it personally as some have.

Why change the engine if all you need is to change the spark plugs.


 
that's just it I don't know the access code....the guy that use to work on this left so now i'm forced to take over for now. which I don't mind.

but I'm trying what bigindian65 typed.
 
your know your routes? prt the local one in ld 21 prt rdr
since your using toll-free - out the local route. acod will show on the prt out. Don't know your route? prt your exchange in 90 (nxx) go to 86 prt that rli - there is your local route, back to 21, there is your acod.

Mato' Was'aka
 
It's probally route 0 and you can print it in
LD 21
REQ PRT
TYPE RDB
RDB 0 Enter until is prints and you will see the ACOD.




This is a Signature and not part of the answer, it appears on every reply.

This is an Analogy so don't take it personally as some have.

Why change the engine if all you need is to change the spark plugs.


 
Okay I got the ACOD it is 511
 
question can someone clear this up.. opp cff, maxp 1 acd ncfw to 9 plus... what is the forwarding ncos.. since an acd does not have a ncos or frl, isn't it still the trunk? if i use cff and maxp 1, i set the inbound trunks to ncos x to allow the call... or use a phantom and rcfw it so i have an ncos..

cff/cfo has almost zero effect on a maxp 1 acd in my switch..

the acod works if the fcr is built as an allow.. and tgar/targ is not blocking... if your coming in and then out on the same route you have to targ x... the routes i use for that have no targ (not 0, just blank)..

john poole
bellsouth business
columbia,sc
 
TIE
sigo:
std - trunk ncos
ESN - orig ncos
ETN - tcos/tcm as FRL

Mato' Was'aka
 
i agree with that, but if your using maxp 1, the only ncos is the inbound trunk... one solution is to build a dsc, frl 0 with a dgt that deletes the orig dialed dn and inserts the 7 digit number.. the forward the set to that dsc, make sure the set has cfxa..


there's always a work around

john poole
bellsouth business
columbia,sc
 
Wonder why that doesn't fly JP, I have not ever had a problem w/ maxp1 fwd?? Seems rare someone gets a funky block...

Mato' Was'aka
 
Status
Not open for further replies.

Part and Inventory Search

Sponsor

Back
Top