How do I get the merlin system's Mac Address?

[borreramos]

I thinking on using that udsip.exe file to set up an static ip address to my merling magix system.
I need to know if this is something I can do and if it is something I can rely on.
Please if you know how to do this please reply.

Thanks in advanced.

Bob Ramos

 

[CarGoSki]

ars restriction

 

[borreramos]

Will this put the system on busy mode CarGoSki?

Let me know

Thanks
Bob

 

[borreramos]

I checked but it is on level 3 (0-6) like the rest of the other ones.

Thanks
Bob

 

[CarGoSki]

print the extension and post.

 

[borreramos]

A EXTENSION INFORMATION


A Extn SS/PP Type
A 321 1/12 4412D+

A CTI Link : No Alarms: ACTIVE
A Pool Access :
A Page Group :
A Primary Coverage :
A Secondary Coverage :
A Coverage Group : 30
A Call Screening : OFF
A Group Coverers : 770
A NS Groups :
A Auxiliary Work Time : NOT ACTIVE
A Group Calling Member: 771
A Group Calling Log In: 771
A Agent ID :
A Pickup Groups :
A Allowed Lists :
A Disallowed Lists : 0 1 2
A Restrictions : UNRESTRICTED
A ESS Sup. Status : NOT ACTIVE
A ESS Restrictions : ESS-2 - NO RESTRICTION
A Auto Callback : OFF
A Call Waiting : OFF
A Abbreviated Ring : ON
A Line Preference : ON
A Shared SA Ring : ON
A Receive Voice Calls : ON
A Coverage Inside : ON
A Forwarding to :
A Delay Forwarding : 0
A Rmt Call Frwd Pool :
A ARS Restriction : 3
A Forced Account Code : Yes
A Microphone Disable : No
A Rotary Enable : No
A Remote Forward Allow: No
A Trunk Transfer Allow: No
A NS Exclusion : No
A Voice Announce Pair : No
A Voice/Data Pair : No
A BIS/HFAI : No
A Language : English
A Authorization Code :
A 2B Data Port : No
A Primary Ring Delay : 2
A Secondary Ring Delay: 2
A Group Cover Delay : 3
A HotLine Extension : No
A Networking and ISDN Display Preference: NUMBER
A Service Observer:
A Service Observing Group:
A EXTENSION INFORMATION


A Extn SS/PP Type
A 321 1/12 4412D+

A Button 34 *21 Blank Status None
A Button 33 *21 Blank Status None
A Button 32 *21 Blank Status None
A Button 31 *21 Blank Status None
A Button 30 *21 Blank Status None
A Button 29 *21 Blank Status None
A Button 28 *21 Blank Status None
A Button 27 *21 Blank Status None
A Button 26 *21 Blank Status None
A Button 25 *21 Blank Status None
A Button 24 *21 Blank Status None
A Button 23 *787 44XX Drop Status None
A Button 22 *21 Blank Status None
A Button 21 *779 HFAI Status None
A Button 20 *21 Blank Status None
A Button 19 *21 Blank Status None
A Button 18 *21 Blank Status None
A Button 17 *21 Blank Status None
A Button 16 *9 Pickup General Status None
A Button 15 *21 Blank Status None
A Button 14 *21 Blank Status None
A Button 13 *21 Blank Status None
A Button 12 *21 Blank Status None
A Button 11 *86 Park Status None
A Button 10 *17 SSA/R 7167/03 -I Status None
A Button 9 *17 SSA/R 7167/02 -I Status None
A Button 8 *17 SSA/R 7167/01 -I Status None
A Button 7 *56 Direct VoiceMail Status Off
A Button 6 *22 Group Call 770 Status None
A Button 5 *21 Blank Status None
A Button 4 Loudspeaker Page
A Button 3 *18 SysAcc-OO Ring Status None
A Shared System Access:
A
A Button 2 *16 SysAcc Voice -I Status None
A Shared System Access:
A
A Button 1 *16 SysAcc Ring -I Status None
A Shared System Access:
A
P3F

 

[borreramos]

I printed anothe rext info that is on the same calling group and that IS able to make outside phone calls and theonly difference between both of them is the "Forced Account Code" the value is "NO" on ext 321 and "YES" on the other ext.

Any Ideas?

Let me know

Thanks
Bob

 

[borreramos]

I wrote that backwards!!!
"Forced Account Code"
Ext 321, VALUE = YES
Ext 322, VALUE = NO (This ext works fine)

 

[CarGoSki]

With forced account code enabled for the extension you are forced to enter an account code before you can dial out. Goto extensions>fAC and delete the extension.

 

[borreramos]

That was IT!!!

Thanks a lot CarGoSki. 321 was the only ext under the Forced Accounts I have no clue how it got there. Is there something that could force them with out you going into the switch and do it manually?


Let me know

Thanks again.

Bob Ramos

 

[borreramos]

Here's another rookie question...
Can I connect to a partner system using winSPM? So far I've tried Magix and also Partner but the modem just keeps dialing and never goes thru.
This is what I sue to dial (External)
9,xxxxxxxxxx,,,,**10
Is this right or wrong?

Thanks
Bob

 

[Dexman]

There is software you can download from Avaya's website for remote connections to Partner ACS processors.

Having said that, establishing a remote connection with a Partner ACS requires the presence of a particular PCMCIA card or (for R7 & R8 processors) an external modem.

Using the PCMCIA method, being able to establish a remote connection to a Partner ACS processor is a crapshoot at best. People have found that a US Robotics "Sportster" or many Lucent modems seem to work the best, but they are not 100%.

That was the reason, starting with the R7 processor, Avaya added a jack that you could use to plug in an external modem.

If it ain't broke, I haven't fixed it yet.

 

[CarGoSki]

You have piled too many different questions into your original thread. You would be best served by starting a new thread.

WinSPM is for Merlin only. Partner has its own software.

 

[borreramos]

Got it. Thanks
Bob