How do I default to Specific Trunk group for Outbounds 2

[tiaka]

Scanario:

1 Main switch with 2 EPNS [G3SI V8]at different locations/buildings [with different addreses]

Just ordered a PRI for out bound traffic at 1 Location
Now I need to make sure all the calls made at this location route out the new trunk.

I seup a new COR and changed the Partition Rounte table for PGN2 to match the new COR still not working

Is there any simple sollution to this?

 

[98Converter]

In the new COR did you set the Time of Day Chart to (2)?



Thanks,
98C

We are what we repeatedly do. Excellence, then, is not an act but a habit. ARISTOTLE 384-322 B.C.

 

[DAVIDPAYNE]

Trunk Group selection is done at the Route Pattern.
1sth the call is match in the ars table and then it is ether a route pattern , or Partition group, that goes to a route pattern.

So do a list ARS route chose on a outbound number and see where it think it needs to go.

Also do you have location setup, if you do, make sure you are working in the correct one.

 

[tiaka]

Thanks for the quick response
Let me make sure Im talking about this right.....Im afraid if I make changes to the ars all calls from all EPNS will route out my ne trunk

i just want users that are sitting in the building to default outbound thru this trunk and not affect any other users/at diff locations...I checked a setup done by AVAYA in Location 3 and they are not using TIME of DAY so I was trying to duplicate what they were doing but Im still missing something.

If I change TOD to 2 its routes out another trunk on Main Switch [Different building/address]Were all in the same area code so ARS routing for specific NPA/NX is not a concern



Can one of send me a setp by step? i have the COR not sure about the PART Group what those mean and I have tons of what looks like unused Routing Tables

 

[DAVIDPAYNE]

That is what the location are for, all you need to do is make sure that you are changing the ars location x for the correct location.

 

[tiaka]

Does PGN in this case mean the same as EPNs
I.E

PGN 1 = Location 01Axxxx Site 1
PGN 2 = Location 02Axxxx Site 2
PGN 3 = Location 03Axxxx Site 3



And the numbers below them are CORs

And the numbers to the side are Route Tables


Routing Patterns
Route
Index PGN 1 PGN 2 PGN 3 PGN 4 PGN 5 PGN 6 PGN 7 PGN 8
----- ----- ----- ----- ----- ----- ----- ----- -----
1 4 4 104
2 6 6 106
3 1 3 101

 

[DAVIDPAYNE]

do a list ars ana location x where x is you location numbers.

 

[98Converter]

I don't think 'tiaka' is using true 'Locations'...

According to your screen shot you have (3) Partition Groups assigned. In each Partition Group you have route patterns. 4,6,1 for PGN 1 - 4,6,3 for PGN2 - and 104,106,101 for PGN3. To apply a phone to one of the PGN's you need to set the TOD on the COR form.

You will need to identify each route pattern - determine where the 'new' trunk group is, and then assign your stations to use that PGN. This is done by changing the TOD on the COR form.

FYI: Time of Day, doesn't literally mean time-of-day, its slightly confusing...

Thanks,
98C

We are what we repeatedly do. Excellence, then, is not an act but a habit. ARISTOTLE 384-322 B.C.

 

[tiaka]

Perfect found it

Didnt know if the numbers below PGN 1 PGN 2 PGN 3 were Route Patterns or CORs

Thanks for your help all