Hicom 300E transfer call "not possible" again..

[WCHPikus]

Hello!
Transfer call from line to line (different card E1, different line) not works again..
On display "not possible"
Call from one E1 trying to transfer to another E1.


I try all, mayby someone see the problem..
My setup:


+------------------------ DIGITAL TRUNK (FORMAT=L) -------------------------+
| DEV = S2CONN PEN = 1-02-037-1 |
|---------------------------------------------------------------------------|
| COTNO = 5 COPNO = 100 DPLN = 1 |
| ITR = 5 COS = 3 LCOSV = 30 |
| LCOSD = 30 CCT = VOIP ADB NEW DESTNO = 0 |
| PROTVAR = ETSI SEGMENT = 1 TCHARG = N |
| SUPPRESS = 0 DGTPR = CHIMAP = N |
| ISDNCC = ISDNAC = ISDNLC = |
| ISDNIP = ISDNNP = |
| PNPL2C = PNPL1C = PNPLC = |
| PNPL2P = PNPL1P = PNPAC = |
| TRACOUNT = 31 SATCOUNT = MANY NNO = 1 -1 -701 |
| ALARMNO = 2 FIDX = 2 CARRIER = 1 |
| ZONE = EMPTY COTX = 211 FWDX = 5 |
| DOMTYPE = DOMAINNO = TPROFNO = |
| INIGHT = |
| CCHDL = UUSCCX = 16 UUSCCY = 8 |
|---------------------------------------------------------------------------|
| TGRP = 402 SRCHMODE = CIR BCNEG = Y |
| BCGR = 1 INS = Y LWPAR = 0 |
| LWPP = 0 LWLT = 0 LWPS = 0 |
| LWR1 = 0 LWR2 = 0 |
| BCHAN 1 && 26 |
| |
+---------------------------------------------------------------------------+

COT: 5 INFO:
DEVICE: INDEP SOURCE: DB
PARAMETER:
PRIORITY FOR AC WILL BE DETERMINED FROM MESSAGE PRI
RECALL IF USER HANGS UP IN CONSULTATION CALL RCL
TRUNK CALL TRANSFER XFER
TRUNK SIGNALING ANSWER ANS
CHANGEOVER FROM HOLD TO RING TONE CHRT
KNOCKING OVERRIDE POSSIBLE KNOR
CALL EXTEND FOR BUSY, RING OR CALL STATE CEBC
NETWORKWIDE AUTOMATIC CALLBACK ON BUSY CBBN
NETWORKWIDE AUTOMATIC CALLBACK ON FREE CBFN
NETWORKWIDE CALL FORWARDING PERMITTED FWDN
DON'T RELEASE CALL TO BUSY HUNT GROUP BSHT
CALL FORWARDING VIA PUBLIC NETWORK REROUTING FWDR
SEND NO NODE NUMBER TO PARTNER LWNC
CONNECTION TO ROUTE OPTIMIZATION NODE ROPT
INCOMING CIRCUIT FROM SYSTEM WITHOUT LCR NLCR
TSC-SIGNALING FOR NETWORKWIDE FEATURES (MANDATORY) TSCS
INCOMING CDR BY ZONE OR FROM LINE ICZL
TRUNK SENDS CALL CHARGES TO ORIGINATING NODE NUMBER TRSC
USE DEFAULT NODE NUMBER OF LINE DFNN
INCOMING CIRCUIT FROM SYSTEM WITHOUT LCR (DATA) NLRD
INTERWORKING CALLBACK - NO ANSWER AND MAILBOX CALLBACK IWCB
AOC PER CALL (AUTOMATICAL OR ON REQUEST), MAND. CORNET-NQ AOCC
LINE WITH IMPLICIT NUMBERS LINO
TRANSFER BEFORE ANSWER ON DSS1 TRBA
DONT SEND DIV_LEG OPERATIONS, BASED ON DSS1 AND QSIG DSDL
NO CFNR AFTER TRANFER POSSIBLE TO NODES BEHIND NCTP
NO TONE NTON


COP: 100 INFO:
DEVICE: INDEP SOURCE: DB
PARAMETER:
DUALTONE MULTIPLEFREQUENCY DTMF
LINE WITH ANSWERING ANS
SPECIAL MODE SFRM
MAKE/BREAK RATIO FOR DTMF 2 (PULSE=150MS,PAUSE=150MS) DTM2

CO TRUNK ACCESS:
TRUNK ACCESS TA

TOLL ACCESS:
TRUNK ACCESS TA

Another line..

+------------------------ DIGITAL TRUNK (FORMAT=L) -------------------------+
| DEV = S2COD PEN = 1-02-025-0 |
|---------------------------------------------------------------------------|
| COTNO = 111 COPNO = 100 DPLN = 1 |
| ITR = 0 COS = 3 LCOSV = 26 |
| LCOSD = 26 CCT = W.PRACOWN. DESTNO = 0 |
| PROTVAR = ETSI SEGMENT = 1 TCHARG = N |
| SUPPRESS = 0 DGTPR = CHIMAP = N |
| ISDNCC = 48 ISDNAC = 68 ISDNLC = 451 |
| ISDNIP = 00 ISDNNP = 0 |
| PNPL2C = PNPL1C = PNPLC = |
| PNPL2P = PNPL1P = PNPAC = |
| TRACOUNT = 31 SATCOUNT = MANY NNO = 1 -1 -100 |
| ALARMNO = 2 FIDX = 1 CARRIER = 1 |
| ZONE = EMPTY COTX = 110 FWDX = 1 |
| DOMTYPE = DOMAINNO = TPROFNO = |
| INIGHT = |
| CCHDL = UUSCCX = 16 UUSCCY = 8 |
|---------------------------------------------------------------------------|
| TGRP = 13 SRCHMODE = CIR BCNEG = N |
| BCGR = 4 INS = Y LWPAR = 0 |
| LWPP = 0 LWLT = 0 LWPS = 0 |
| LWR1 = 0 LWR2 = 0 |
| BCHAN 29 && 30 |
| |
+---------------------------------------------------------------------------+
COT: 111 INFO:
DEVICE: INDEP SOURCE: DB
PARAMETER:
RECALL IF USER HANGS UP IN CONSULTATION CALL RCL
TRUNK CALL TRANSFER XFER
TRUNK SIGNALING ANSWER ANS
CHANGEOVER FROM HOLD TO RING TONE CHRT
CALL EXTEND FOR BUSY, RING OR CALL STATE CEBC
NETWORKWIDE AUTOMATIC CALLBACK ON BUSY CBBN
NETWORKWIDE AUTOMATIC CALLBACK ON FREE CBFN
NETWORKWIDE CALL FORWARDING PERMITTED FWDN
DON'T RELEASE CALL TO BUSY HUNT GROUP BSHT
CALL FORWARDING VIA PUBLIC NETWORK REROUTING FWDR
SEND NO NODE NUMBER TO PARTNER LWNC
INCOMING CIRCUIT FROM SYSTEM WITHOUT LCR NLCR
TSC-SIGNALING FOR NETWORKWIDE FEATURES (MANDATORY) TSCS
INCOMING CDR BY ZONE OR FROM LINE ICZL
TRUNK SENDS CALL CHARGES TO ORIGINATING NODE NUMBER TRSC
USE DEFAULT NODE NUMBER OF LINE DFNN
INCOMING CIRCUIT FROM SYSTEM WITHOUT LCR (DATA) NLRD
INTERWORKING CALLBACK - NO ANSWER AND MAILBOX CALLBACK IWCB
LINE WITH IMPLICIT NUMBERS LINO
TRANSFER BEFORE ANSWER ON DSS1 TRBA
DONT SEND DIV_LEG OPERATIONS, BASED ON DSS1 AND QSIG DSDL
NO CFNR AFTER TRANFER POSSIBLE TO NODES BEHIND NCTP
NO TONE NTON



COP: 100 INFO:
DEVICE: INDEP SOURCE: DB
PARAMETER:
DUALTONE MULTIPLEFREQUENCY DTMF
LINE WITH ANSWERING ANS
SPECIAL MODE SFRM
MAKE/BREAK RATIO FOR DTMF 2 (PULSE=150MS,PAUSE=150MS) DTM2

CO TRUNK ACCESS:
TRUNK ACCESS TA

TOLL ACCESS:
TRUNK ACCESS TA

Any idea?

 

[WCHPikus]

Sorry, offcourse Hicom Europe version..

 

[donb01]

If it WAS working (for more than just a few minutes) and now it doesn't again, unless you changed anything in the config, I would try to deactivate and re-seat both of the boards during a time of little to no traffic and then activate them again. If it then works again, or works temporarily again, you will have some idea it may be closer to a hardware problem than a configuration problem.

 

[WCHPikus]

Hi!
No, i had this problem some time ago,but do not remember how to solve this
I created new trunk (my card was broken, but only one port), so i have to create new trunk on the new one.
The same config, but not work..
Mayby some with DNNO or trafic between trunks, cot, cop...do not know..

 

[donb01]

Make sure when you connected the wires to the new port that you punched them down with the correct polarity - I've been known to have that issue. If you duplicated what you already have working on the new port, activated the new port, and made sure you included the new port in the same trunk group the old one was in I can't see why it doesn't work.