Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

  • Congratulations strongm on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Hicom 300 call from CO to CO not work

Status
Not open for further replies.

WCHPikus

Technical User
Jan 17, 2005
46
Hello!
I have two line DEV = S2COD
One to router (1), second to City (2)..
Call from ext to 1 work, from ext to 2 works..
But from line 1 to line 2 not.
In debug no message (setup) from line 1 in line 2
Any idea?

line 1:
+------------------------ DIGITAL TRUNK (FORMAT=L) -------------------------+
| DEV = S2COD PEN = 1-02-025-1 |
|---------------------------------------------------------------------------|
| COTNO = 111 COPNO = 100 DPLN = 1 |
| ITR = 5 COS = 3 LCOSV = 30 |
| LCOSD = 30 CCT = VOIP ADB DESTNO = 0 |
| PROTVAR = ETSI SEGMENT = 1 TCHARG = N |
| SUPPRESS = 0 DGTPR = CHIMAP = N |
| ISDNCC = ISDNAC = ISDNLC = |
| ISDNIP = ISDNNP = |
| PNPL2C = PNPL1C = PNPLC = |
| PNPL2P = PNPL1P = PNPAC = |
| TRACOUNT = 31 SATCOUNT = MANY NNO = 1 -1 -100 |
| ALARMNO = 2 FIDX = 1 CARRIER = 1 |
| ZONE = EMPTY COTX = 110 FWDX = 5 |
| DOMTYPE = DOMAINNO = TPROFNO = |
| INIGHT = |
| CCHDL = UUSCCX = 16 UUSCCY = 8 |
|---------------------------------------------------------------------------|
| TGRP = 401 SRCHMODE = CIR BCNEG = Y |
| BCGR = 1 INS = Y LWPAR = 0 |
| LWPP = 0 LWLT = 0 LWPS = 0 |
| LWR1 = 0 LWR2 = 0 |
| BCHAN 1 && 30 |
| |
+---------------------------------------------------------------------------+

line 2:

+------------------------ DIGITAL TRUNK (FORMAT=L) -------------------------+
| DEV = S2COD PEN = 1-02-025-0 |
|---------------------------------------------------------------------------|
| COTNO = 111 COPNO = 100 DPLN = 1 |
| ITR = 5 COS = 3 LCOSV = 26 |
| LCOSD = 26 CCT = W.PRZYCHODZ. DESTNO = 0 |
| PROTVAR = ETSI SEGMENT = 1 TCHARG = N |
| SUPPRESS = 0 DGTPR = CHIMAP = N |
| ISDNCC = 48 ISDNAC = 68 ISDNLC = 451 |
| ISDNIP = 00 ISDNNP = 0 |
| PNPL2C = PNPL1C = PNPLC = |
| PNPL2P = PNPL1P = PNPAC = |
| TRACOUNT = 31 SATCOUNT = MANY NNO = 1 -1 -100 |
| ALARMNO = 2 FIDX = 1 CARRIER = 1 |
| ZONE = EMPTY COTX = 110 FWDX = 5 |
| DOMTYPE = DOMAINNO = TPROFNO = |
| INIGHT = |
| CCHDL = UUSCCX = 16 UUSCCY = 8 |
|---------------------------------------------------------------------------|
| TGRP = 10 SRCHMODE = CIR BCNEG = N |
| BCGR = 1 INS = Y LWPAR = 0 |
| LWPP = 0 LWLT = 0 LWPS = 0 |
| LWR1 = 0 LWR2 = 0 |
| BCHAN 1 && 10 |
| |
+---------------------------------------------------------------------------+
+------------------------ DIGITAL TRUNK (FORMAT=L) -------------------------+
| DEV = S2COD PEN = 1-02-025-0 |
|---------------------------------------------------------------------------|
| COTNO = 111 COPNO = 100 DPLN = 1 |
| ITR = 0 COS = 3 LCOSV = 26 |
| LCOSD = 26 CCT = W.SPECJAL. DESTNO = 0 |
| PROTVAR = ETSI SEGMENT = 1 TCHARG = N |
| SUPPRESS = 0 DGTPR = CHIMAP = N |
| ISDNCC = 48 ISDNAC = 68 ISDNLC = 451 |
| ISDNIP = 00 ISDNNP = 0 |
| PNPL2C = PNPL1C = PNPLC = |
| PNPL2P = PNPL1P = PNPAC = |
| TRACOUNT = 31 SATCOUNT = MANY NNO = 1 -1 -100 |
| ALARMNO = 2 FIDX = 1 CARRIER = 1 |
| ZONE = EMPTY COTX = 110 FWDX = 1 |
| DOMTYPE = DOMAINNO = TPROFNO = |
| INIGHT = |
| CCHDL = UUSCCX = 16 UUSCCY = 8 |
|---------------------------------------------------------------------------|
| TGRP = 12 SRCHMODE = CIR BCNEG = N |
| BCGR = 3 INS = Y LWPAR = 0 |
| LWPP = 0 LWLT = 0 LWPS = 0 |
| LWR1 = 0 LWR2 = 0 |
| BCHAN 26 && 28 |
| |
+---------------------------------------------------------------------------+
+------------------------ DIGITAL TRUNK (FORMAT=L) -------------------------+
| DEV = S2COD PEN = 1-02-025-0 |
|---------------------------------------------------------------------------|
| COTNO = 111 COPNO = 100 DPLN = 1 |
| ITR = 0 COS = 3 LCOSV = 26 |
| LCOSD = 26 CCT = W.PRACOWN. DESTNO = 0 |
| PROTVAR = ETSI SEGMENT = 1 TCHARG = N |
| SUPPRESS = 0 DGTPR = CHIMAP = N |
| ISDNCC = 48 ISDNAC = 68 ISDNLC = 451 |
| ISDNIP = 00 ISDNNP = 0 |
| PNPL2C = PNPL1C = PNPLC = |
| PNPL2P = PNPL1P = PNPAC = |
| TRACOUNT = 31 SATCOUNT = MANY NNO = 1 -1 -100 |
| ALARMNO = 2 FIDX = 1 CARRIER = 1 |
| ZONE = EMPTY COTX = 110 FWDX = 1 |
| DOMTYPE = DOMAINNO = TPROFNO = |
| INIGHT = |
| CCHDL = UUSCCX = 16 UUSCCY = 8 |
|---------------------------------------------------------------------------|
| TGRP = 13 SRCHMODE = CIR BCNEG = N |
| BCGR = 4 INS = Y LWPAR = 0 |
| LWPP = 0 LWLT = 0 LWPS = 0 |
| LWR1 = 0 LWR2 = 0 |
| BCHAN 29 && 30 |
| |
+---------------------------------------------------------------------------+
+------------------------ DIGITAL TRUNK (FORMAT=L) -------------------------+
| DEV = S2COD PEN = 1-02-025-0 |
|---------------------------------------------------------------------------|
| COTNO = 111 COPNO = 100 DPLN = 1 |
| ITR = 5 COS = 3 LCOSV = 26 |
| LCOSD = 26 CCT = W.DYREKTOR. DESTNO = 0 |
| PROTVAR = ETSI SEGMENT = 1 TCHARG = N |
| SUPPRESS = 0 DGTPR = CHIMAP = N |
| ISDNCC = 48 ISDNAC = 68 ISDNLC = 451 |
| ISDNIP = 00 ISDNNP = 0 |
| PNPL2C = PNPL1C = PNPLC = |
| PNPL2P = PNPL1P = PNPAC = |
| TRACOUNT = 31 SATCOUNT = MANY NNO = 1 -1 -100 |
| ALARMNO = 2 FIDX = 1 CARRIER = 1 |
| ZONE = EMPTY COTX = 110 FWDX = 1 |
| DOMTYPE = DOMAINNO = TPROFNO = |
| INIGHT = |
| CCHDL = UUSCCX = 16 UUSCCY = 8 |
|---------------------------------------------------------------------------|
| TGRP = 11 SRCHMODE = CIR BCNEG = N |
| BCGR = 5 INS = Y LWPAR = 0 |
| LWPP = 0 LWLT = 0 LWPS = 0 |
| LWR1 = 0 LWR2 = 0 |
| BCHAN 21 && 25 |
| |
+---------------------------------------------------------------------------+
+------------------------ DIGITAL TRUNK (FORMAT=L) -------------------------+
| DEV = S2COD PEN = 1-02-025-0 |
|---------------------------------------------------------------------------|
| COTNO = 111 COPNO = 100 DPLN = 1 |
| ITR = 5 COS = 3 LCOSV = 26 |
| LCOSD = 26 CCT = W.PRZYCHODZ. DESTNO = 0 |
| PROTVAR = ETSI SEGMENT = 1 TCHARG = N |
| SUPPRESS = 0 DGTPR = CHIMAP = N |
| ISDNCC = 48 ISDNAC = 68 ISDNLC = 451 |
| ISDNIP = 00 ISDNNP = 0 |
| PNPL2C = PNPL1C = PNPLC = |
| PNPL2P = PNPL1P = PNPAC = |
| TRACOUNT = 31 SATCOUNT = MANY NNO = 1 -1 -100 |
| ALARMNO = 2 FIDX = 1 CARRIER = 1 |
| ZONE = EMPTY COTX = 110 FWDX = 5 |
| DOMTYPE = DOMAINNO = TPROFNO = |
| INIGHT = |
| CCHDL = UUSCCX = 16 UUSCCY = 8 |
|---------------------------------------------------------------------------|
| TGRP = 10 SRCHMODE = CIR BCNEG = N |
| BCGR = 6 INS = Y LWPAR = 0 |
| LWPP = 0 LWLT = 0 LWPS = 0 |
| LWR1 = 0 LWR2 = 0 |
| BCHAN 11 && 20 |
| |
+---------------------------------------------------------------------------+

cot and cos:
DIS-COT:111,;
H500: AMO COT STARTED

COT: 111 INFO:
DEVICE: INDEP SOURCE: DB
PARAMETER:
RECALL IF USER HANGS UP IN CONSULTATION CALL RCL
TRUNK CALL TRANSFER XFER
TRUNK SIGNALING ANSWER ANS
CHANGEOVER FROM HOLD TO RING TONE CHRT
CALL EXTEND FOR BUSY, RING OR CALL STATE CEBC
NETWORKWIDE AUTOMATIC CALLBACK ON BUSY CBBN
NETWORKWIDE AUTOMATIC CALLBACK ON FREE CBFN
NETWORKWIDE CALL FORWARDING PERMITTED FWDN
DON'T RELEASE CALL TO BUSY HUNT GROUP BSHT
CALL FORWARDING VIA PUBLIC NETWORK REROUTING FWDR
SEND NO NODE NUMBER TO PARTNER LWNC
INCOMING CIRCUIT FROM SYSTEM WITHOUT LCR NLCR
TSC-SIGNALING FOR NETWORKWIDE FEATURES (MANDATORY) TSCS
INCOMING CDR BY ZONE OR FROM LINE ICZL
TRUNK SENDS CALL CHARGES TO ORIGINATING NODE NUMBER TRSC
USE DEFAULT NODE NUMBER OF LINE DFNN
INCOMING CIRCUIT FROM SYSTEM WITHOUT LCR (DATA) NLRD
INTERWORKING CALLBACK - NO ANSWER AND MAILBOX CALLBACK IWCB
LINE WITH IMPLICIT NUMBERS LINO
TRANSFER BEFORE ANSWER ON DSS1 TRBA
DONT SEND DIV_LEG OPERATIONS, BASED ON DSS1 AND QSIG DSDL
NO CFNR AFTER TRANFER POSSIBLE TO NODES BEHIND NCTP
NO TONE NTON



DIS-COSSU:COS,3,;
H500: AMO COSSU STARTED
+------+----------+---------+---------+---------+----------+
| COS | VOICE | FAX | TTX | VTX | DTE |
+------+----------+---------+---------+---------+----------+
| 3 |> |
| | TA | TA | TA | TA | TA |
| | TNOTCR | TNOTCR | TNOTCR | TNOTCR | TNOTCR |
| | RKOABS | BASIC | BASIC | BASIC | BASIC |
| | CDRINT | | | | MSN |
| | CDRS | | | | CDRINT |
| | CDRC | | | | MULTRA |
| | COSXCD | | | | |
| | VCE | | | | |
| | DATA | | | | |
| | FWDNWK | | | | |
| | REOVR | | | | |
| | FWDBSY | | | | |
| | FWDECA | | | | |
| | FWDFAS | | | | |
| | FWDBAS | | | | |
| | FWDEXT | | | | |
| | | | | | |
+------+----------+---------+---------+---------+----------+

zand


DIS-ZAND:ALLDATA;
H500: AMO ZAND STARTED

GENERAL SYSTEM DATA:
====================

TRANSFER = EXTEND , ALERTN = NO ,
AUTHUP = TA ,
RNGBKTN = YES , TRANSINH = YES , INIGHT = NO ,
NIGHT = TA ,
ITRFWD = NO , HOLDTN = MUSIC ,
ANATESIG = TONE , DSSLT = 10, CODTN = YES ,
CONFSUB = NO , CONANS = YES , DATEDIS = DDMM,
CNTRYCD = F , RCLLT = NO , MELODY = 1,
TRCD = , CPBLOWL = 80 , CPBUPPL = 100,
CUTHRU1A = NO , PREDIA = YES , SIUANN = 2,
CO = NO , COEXN = 0 , CBKNO = 5 ,
SEVDIG = NO , NNO = 1 -1 -1 ,
DISPMODE = MODE1, NODECD = 701 ,
ROUTOPTP = YES , ROUTOPTD = NO , CALLOFF = NO ,
PARARING = YES ,
DSSDEST = NO , ONEPARTY = NO , MSGDELAY = NO ,
COBUSY = NO , EXCOCO = YES , TRDGTPR = NO ,
COANN = NO , HOTDIAL = NO , TRANSTOG = NO ,
NOCFW = NO , HOLDHUNT = NO , POSTDDLY = NO ,
EXBUSYOV = NO , OVRMST = NO , OVRHUNT = NO ,
CONITPRO = YES , RECHUNT = NO , CALLACMP = NO ,
NETTEAM = NO , CFWLOOP = NO ;

AMO-ZAND -111 SYSTEM DATA


Another question
What is diference TIE and CO?
Mayby in tdcsu dev must be S2CONN??
 
Is this a new trunk installation? What type of trunk are you trying to install? ISDN PRI, TDM-based Cornet, Cornet IP?
 
donb01:
TTT?
What is it the parametr?
I did't see in cossu..



New trunk E1, PRI Esti (euro isdn)
 
donb01:
TTT?
What is it the parametr?
I did't see in cossu..



New trunk E1, PRI Etsi (euro isdn)
 
I have only this in cot:

POSSIBLE VALUES : NOCO NO CENTRAL OFFICE ACCESS
TA UNRESTRICTED TOLL ACCESS
COSXCD COS CHANGEOVER BY CODE
DICT DICTATION AUTHORIZATION
CDRC CALL DETAIL RECORDING CENTRAL
AHOT HOTLINE
VCE ACCESS TO SERVICE MODULE (VOICE)
RSVLN RESERVE LINE
RTA RESTRICTED TRUNK ACCESS
RTA1 RESTRICTED TRUNK ACCESS 1
RTA2 RESTRICTED TRUNK ACCESS 2
RTA3 RESTRICTED TRUNK ACCESS 3
RTA4 RESTRICTED TRUNK ACCESS 4
RTA5 RESTRICTED TRUNK ACCESS 5
RTA6 RESTRICTED TRUNK ACCESS 6
NOTIE NO TIE LINE ACCESS
RTIEA RESTRICTED TIE ACCESS
TNOTCR TIE LINE WITH NO TOLL CODE RESTRICTION
TTCR1 TIE ACCESS WITH TOLL CODE RESTRICTION 1
CONTINUE ? (Y/N)

POSSIBLE VALUES : TTCR2 TIE ACCESS WITH TOLL CODE RESTRICTION 2
TTCR3 TIE ACCESS WITH TOLL CODE RESTRICTION 3
TTCR4 TIE ACCESS WITH TOLL CODE RESTRICTION 4
TTCR5 TIE ACCESS WITH TOLL CODE RESTRICTION 5
TTCR6 TIE ACCESS WITH TOLL CODE RESTRICTION 6
DNDOVR DO NOT DISTURB OVERRIDE
RKOABS REJECT KNOCKING/OVERRIDE, ABSOLUTE
DIDBLK DIRECT-IN-DIAL BLOCKING
PRISTN STATION WITH PRIORITY
CDRATN CALL DETAIL RECORDING AT ATTENDANT
CDRSTN IMMEDIATE CALL DETAIL RECORDING DISPLAY
CDRS CALL DETAIL RECORDING PER STATION
MB MAILBOX
SPKR LOUDSPEAKER AUTHORIZATION
DATA DATA AUTHORIZATION
TRACE AUTOMATIC MALICIOUS CALL TRACING
NOANSA NO ANSWER ADVANCE
HOT HOTLINE
OFHKRC CODE BLUE
TSUID TRUNK SUBSCRIBER IDENTIFICATION
NOCHRG WITHOUT CHARGE
FWDNWK CALL FORWARDING TO NETWORK (I.E. EXTERNAL DEST.)
CONTINUE ? (Y/N)

POSSIBLE VALUES : MTRACE MANUAL CALL TRACE IN ISDN
ATRACE AUTOMATIC CALL TRACE IN ISDN
PRCO CO SUBSCRIBER WITH PRIORITY
PRCO1 CO SUBSCRIBER WITH PRIORITY 1
COIN PUBLIC COIN OPERATED TELEPHONE
RERING RING BACK
AUTOV AUTOMATIC OVERRIDE
RELCON RELEASE CONTROL
LOCC LOCAL CALL
NATC NATIONAL CALL
INATC INTERNATIONAL CALL
LSVC LOCAL SERVICE
NSVC NATIONAL SERVICE
TOLLC TOLL CALL
LOCCNV LOCAL DATA (NON-VOICE) CALL
TOLLOP TOLL OPERATOR
CDRIND INDIVIDUAL CALL DETAIL RECORDING IN CO
TESTEQ TEST EQUIPMENT
REOVR REJECTION OF EMERGENCY OVERRIDE
OVCAT OVERRIDE CATEGORIE
SPECAR SPECIAL-ARRANGEMENT
SUBCAL B IS NOTIFIED OF THE NUMBER OF STATION A
CONTINUE ? (Y/N)

POSSIBLE VALUES : SUBDB B IS NOTIFIED OF THE DEFAULT NUMBER OF STATION B
SUBMSN B IS NOTIFIED OF THE MSN
FWDBSY CALL FORWARDING TO FWD DESTINATION IF BUSY
MSN MULTIPLE SUBSCRIBER NUMBER(SEND CALLED PARTY NO)
TRANSG INDIR. ACCESS TO PRIV. NETWORK VIA PUBLIC NETW.
NOARNO AUT. RECALL MUST BE DEACT. FOR SUBSC. LINE CIR.
NOPTCD CHANGE NIGHT OPT. OF AN AC GROUP BY DIAL. A CODE
MULTRA MULTI-TRANS (CALL. STATION SEIZED SEVERAL TIMES)
DSSKEY KEY FUNCTIONS VIA DSS KEYS
MANOV MANUAL OVERRIDE
CDRINT CALL DETAIL RECORDING OF INTERNAL CALLS
REVCHA SUBSCRIBER WITH REVERSE CHARGING
LOCCPV LOCAL DATA IN PRIVAT NETWORK
TOLLPV TOLL CALL IN PRIVAT NETWORK
INATCP INTERNATIONAL CALL IN PRIVAT NETWORK
ANSYN ANNOUNCEMENTS WITH SYNCHRONOUS START OF TEXT
FWDECA CALLFORWARDING EXTERNAL CALL
FWDFAS CALLFORWARDING PROGRAM FOR ANOTHER SUBSCRIBER
FWDBAS CALLFORWARDING PROGRAM BY ANOTHER SUBSCRIBER
FWDDIR AKT/DEACT U QUERY OF CALLFORWARD INCOMING
KIESIG KEYPAD IE SIGNALING POSSIBLE
ANITC ISSUING A BILL FOR A LONG-DISTANCE TOLL CALL
CONTINUE ? (Y/N)

POSSIBLE VALUES : ANIPS ISSUING A BILL FOR SAME SERVCES REQ. PAYMENT
ANICT MALICIOUS CALL TRACING
ANISS INFO ABOUT REACHING SOME SPECIAL SERVICES
CFSWF SWITCH-OVER CALLFORWARD FIX TO CALLF. VARIABLE
RECOIG RELEASE CONTROL IGNOR
SUBEPP THE CONSULTING PARTY IS RESPONSIBLE FOR CHARGE
DPSTN DIAL PULSE SIGNALLING
CCBS COMPLETION OF CALLS TO BUSY SUBSCRIBER
COLR CONNECTED LINE IDENTIFICATION RESTRICTION
CW CALL WAITING
MFPIAC MFRP INTRAZONE AUTOMATIC CALL ACCESS CODE 2
MFPAIC MFRP AUTOMATIC INTERNATIONAL CALL
MFPSTC MFRP SEMIAUTOMATIC TOLL CALL ACCESS CODE ABC
MFPSIC MFRP SEMIAUTOMATIC INTERNATIONAL CALL
FWDEXT EXTENDED CALL FORWARDING
SCRSPC SUBSCRIBER WITH SPECIAL CHARGING
MTEQ MAINTENANCE EQUIPEMENT
PUPHON PUBLIC PHONE
SCRNCA SUBSCRIBER WITH NO CHARGE PARTY A
SCRNCB SUBSCRIBER WITH NO CHARGE PARTY B
FWDBAR CALL FORWARDING BARRING
GRPCAL GROUP CALL
CONTINUE ? (Y/N)

POSSIBLE VALUES : HGICLD HUNTING GROUP NUMBER IN CALL PARTY NUMBER
AOBTR AUTOMATIC EMERGENCY OVERWRIDE ON A BUSY TRUNK
TP TERMINAL PORTABILITY
MCIDM MALICIOUS CALL IDENTIFICATION - MANUAL
MCIDA MALICIOUS CALL IDENTIFICATION - AUTO
UUS1IM USE OF USER - USER SIGNALING 1 IMPLICIT
UUS3 USE OF USER - USER SIGNALING 3
BDCP BLOCKING OF DIRECTED CALL PICKUP
CTLS CONTROLLED TRUNK AND LINE SELECTION
SUTVA STATION USER TRANSFERE BEFORE ANSWER
 
I was referring to COS. Here is what's set up for my trunks. I have ISDN PRI coming in and CorNet between sites.

DIS-COSSU:COS,;
H500: AMO COSSU STARTED
+------+-----------------+---------------+-----------------+
| COS | VOICE | FAX | DTE |
+------+-----------------+---------------+-----------------+
| 1 |>ANALOG |
| | TA | NOCO | NOCO |
| | TNOTCR | NOTIE | NOTIE |
| | MB | | |
| | FWDECA | | |
| | CCBS | | |
| 5 |>OPTISETS |
| | TA | NOCO | NOCO |
| | TNOTCR | NOTIE | NOTIE |
| | MB | | |
| | CFNR | | |
| | TTT | | |
| | CFB | | |
| | FWDECA | | |
| | FWDEXT | | |
| | CCBS | | |
| 10 |>TRUNKS |
| | TA | NOCO | NOCO |
| | TNOTCR | NOTIE | NOTIE |
| | MB | | |
| | TTT | | |
| | CTLS | | |
| 11 |>ANALOG HOTLN |
| | TA | NOCO | NOCO |
| | TNOTCR | NOTIE | NOTIE |
| | MB | | |
| | HOT | | |
| | FWDECA | | |
| | CCBS | | |
+------+-----------------+---------------+-----------------+
 
Cos offcourse..

I do not have this option in my Hicom 300E...
available options upper my post..
Could You develop this shortcut TTT??

Regards
 
You listed your COS above like this:

DIS-COSSU:COS,3,;
H500: AMO COSSU STARTED
+------+----------+---------+---------+---------+----------+
| COS | VOICE | FAX | TTX | VTX | DTE |
+------+----------+---------+---------+---------+----------+
| 3 |> |
| | TA | TA | TA | TA | TA |
| | TNOTCR | TNOTCR | TNOTCR | TNOTCR | TNOTCR |
| | RKOABS | BASIC | BASIC | BASIC | BASIC |
| | CDRINT | | | | MSN |
| | CDRS | | | | CDRINT |
| | CDRC | | | | MULTRA |
| | COSXCD | | | | |
| | VCE | | | | |
| | DATA | | | | |
| | FWDNWK | | | | |
| | REOVR | | | | |
| | FWDBSY | | | | |
| | FWDECA | | | | |
| | FWDFAS | | | | |
| | FWDBAS | | | | |
| | FWDEXT | | | | |
| | | | | | |
+------+----------+---------+---------+---------+----------+

So if this is the right COS you would do something like this:

CHA-COSSU:COS,3

and when it asks you for the AVCE parameter (Add Voice) enter: TTT and finish with a ; semicolon.

Do not make any entries for anything that looks like DVCE, DFAX, or DDTE because that actually deletes parameters out of the COS.


 
I wrote, i do not have TTT option...
cha-cossu
TYPE = cos
COS = 3
AVCE = ttt
M34: VALUE NOT WITHIN ADMISSIBLE RANGE

No TTT parametr in cossu AMO.
 
WCHPikus has the European version of the Hicom 300, which used different AMOs from the USA Hicom 300. Remember that the USA version of the Hicom 300 was completely re-engineered in Boca Raton, Florida shortly after Siemens AG bought into the ROLM/IBM joint venture in 1989/1990.

The European Hicom 300 used AMOs which are very similar but not a perfect match with HiPath 4000 V1. So even though those AMO names sound familiar, the Euro-Hicom 300 AMO/parameter issues should be handled by European Hicom 300 technicians!

This "Siemens Hicom" forum is used worldwide for seeking answers to problems with IBM 9751, ROLM CBX 9000, ROLM CBX 8000, PhoneMail, Xpressions, Euro Hicom 300E, USA Hicom 300E & 300H, HiPath 4000 V1-V6, Realitis/HiPath DX, Siemens 9200, and MANY more systems/apps/servers. It would be helpful if each new post can identify the type of system involved - to avoid confusion.
 
Sorry. I saw that he had said Hicom 300, which I have the USA version of, and was giving the "HiPath 4000" command set, which led me to believe he had a european switch, but I did not know that the 4000 command syntax was not the same as the Hicom 300 European command syntax - so many things have matched over time that it was easy enough to assume. Same as the HiPath 3000 and my Hicom 150. The 150 is a 3.0 /Hv1.0, which I was told is what the 3000 was when it first came out, so I have always used those references there too.

So, either way, whatever their version of TTT is does not look like it is in his COS.... :)
 
Status
Not open for further replies.

Part and Inventory Search

Sponsor

Back
Top