Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

  • Congratulations strongm on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Hi Folks, I have an EXTN card whic

Status
Not open for further replies.

Steve5512

Technical User
Jul 10, 2020
36
RO
Hi Folks,
I have an EXTN card which after I installed it in an Spare slot and activated all ports and installed and activate all channels with all EXTN numbers, I don`t have any dialing tone on any of these EXTN ports. Bellow I will detail everything I did in settings :
lslt 0422 c
0422 SPARE
rslt 0422 extn
lslt 0422 c

ieq 042201
EC 042201 INSTALLED
ieq 042202
EC 042202 INSTALLED
ieq 042203
EC 042203 INSTALLED
ieq 042204
EC 042204 INSTALLED
ieq 042205
EC 042205 INSTALLED
ieq 042206
EC 042206 INSTALLED
ieq 042207
EC 042207 INSTALLED
ieq 042208
EC 042208 INSTALLED
ieq 042209
EC 042209 INSTALLED
ieq 042210
EC 042210 INSTALLED
ieq 042211
EC 042211 INSTALLED
ieq 042212
EC 042212 INSTALLED
ieq 042213
EC 042213 INSTALLED
ieq 042214
EC 042214 INSTALLED
ieq 042215
EC 042215 INSTALLED
ieq 042216
EC 042216 INSTALLED


nex 5820
nex 5880
nex 5808
nex 5067
nex 5055
nex 5075
nex 5003
nex 5066
nex 5053
nex 5002
nex 5004
nex 5010
nex 5801
nex 5807
nex 5803
nex 5802
nex 5804
nex 5805

nch 5808 042216
nch 5067 042201
nch 5055 042202
nch 5075 042203
nch 5003 042204
nch 5066 042205
nch 5053 042206
nch 5002 042207
nch 5004 042208
nch 5010 042209
nch 5801 042210
nch 5807 042211
nch 5803 042212
nch 5802 042213
nch 5804 042214
nch 5805 042215
nch 5808 042216

scs 5067 30
stac 5067 30
scs 5055 30
stac 5055 30
scs 5075 30
stac 5075 30
scs 5003 30
stac 5003 30
scs 5066 30
stac 5066 30
scs 5053 30
stac 5053 30
scs 5002 30
stac 5002 30
scs 5004 30
stac 5004 30
scs 5010 30
stac 5010 30
scs 5801 30
stac 5801 30
scs 5807 30
stac 5807 30
scs 5803 30
stac 5803 30
scs 5802 30
stac 5802 30
scs 5804 30
stac 5804 30
scs 5805 30
stac 5805 30
scs 5808 30
stac 5808 30

lch 0422
EC042201 EN5067 MF4 TEST
EC042202 EN5055 MF4 TEST
EC042203 EN5075 MF4 TEST
EC042204 EN5003 MF4 TEST
EC042205 EN5066 MF4 TEST
EC042206 EN5053 MF4 TEST
EC042207 EN5002 MF4 TEST
EC042208 EN5004 MF4 TEST
EC042209 EN5010 MF4 TEST
EC042210 EN5801 MF4 TEST
EC042211 EN5807 MF4 TEST
EC042212 EN5803 MF4 TEST
EC042213 EN5802 MF4 TEST
EC042214 EN5804 MF4 TEST
EC042215 EN5805 MF4 TEST
EC042216 EN5808 MF4 TEST

Can anybody give me an idea of what I missed, or did wrong in my settings ?

Stefan
 
When give AEQ the answer is it`s already activated.
 
Can you swap cards with a known working one ?

I suspect a cable at the backplane
 
I already did it but result was the same, soI suspect the backplane card or the shelf bus more than anything else.
Unfortunately for me I dodn`t have direct access to any spare parts supplier, that`s why I resume myself just trying to guess the cause of all these than tofind a real remedy.
 
What parts do you need - I know of an old iSDX coming out soon which may help - let me know
 
Mine is an DX-150E which doesn`t match at all with iSDX. I have an old iSDX/L inhere in standby just in case of spmething, so I already had this experience, believe me.
I need any of the following as spare parts :
P1 Control B backplane 1HBC50072
P1 Control A backplane 1HBC50071
P2 Telephony backplane 1HBC50016
P1 Telephony backplane 1HBC50010
EXTN interface card 1HAB50083AAK
EXTN filter card 1HAU50448
Ribbon cables for IMC card - both for data and addresses connectors, EXTN card too.
Any of these would be very useful for me in my work here.
 
It will take a while and not sure if the L that I know of has any/all of these but will let you know
 
More than sure you will not find any of these cards on iSDX/L, because as I already told you, I have one inhere on my site and nothing match with the DX-150E which is a Dual Processor type.
 
Hi Steve5512

A DX-150E has 1 shelf and 14 slots, from your previous posts it looks like to have a "HiPath DX" which is the module/stack based system.

Looking at the cabinet map in your previous post, slot 0422 seems to have been missed out which is slightly suspicious. Possibly never worked from day one. Have a look at the P2 Telephony backplane 1HBC50016 where the pins connect to the analogue extension card. Check to see if any of the pins are bent and the card is seating correctly.

Wiring and Filter -
Filter should be a 1HAM 50049 AAG (Analogue terminal filter card) which is different to a DX-150E analogue filter!
Cable should be 871/1/10228 to MDF, or 1HAU 50448 *** to Extension (2-wire) patch pan
Use the cable and filter from slot 0421 to test with.

Also, the extension card should be set to single slot working and your programming looks OK.
 
Thanks buddy for your advice, but I already did everything you said earlier, beside all these my system is :
Siemens Real;itis HiPath DX-150E Dual procesor with 28 slots on each of the 4 shelves I have inhere.
For the moment I abandoned the search because I couldn`t find any spare parts for the P2 Telephony backplane 1HBC50016 and the only place I found it the price was to high and didn`t worth it. What I would be more imnterested in would be an entire extension shelf equiped with only 3cards, 2 shelf interface for CPU-A and CPU-B and an CEC card, with all the ribbon cables installed on the back of the backplane card, in case I would like to install any other cards in the spare slots. The only important thing would be to be a match to my existing PBX system, nothing else. If you can help me with these just let me a price and we can talk further about all these things in private, first by email and after on Whatsapp if you want it too.
 
Not sure how we IM each other on this forum but if you some how post and get an email to me, I will replay back with my contact details.
 
cristeasta yahoo com
You can contact me directly there if you want to help me find an entire extension shelf equiped with only 3cards, 2 shelf interface for CPU-A and CPU-B and an CEC card, with all the ribbon cables installed on the back of the backplane card, in case I would like to install any other cards in the spare slots.
The only thing I need is to be a perfect match to my actual PBX :
Siemens Realitis HiPath DX-150E Dual Processor with 28 slots
In present I have 4 Shelf installed inhere and I think the best solution would be to install another extension Shelf.
 
Status
Not open for further replies.

Part and Inventory Search

Sponsor

Back
Top