H in front of the Ext No. when calling over PRI Network

[Matt2010]

Hi,

I recently set up a PRI to PRI network on a couple of CS1K's. When I call across the network ( both ways ) a H is placed in front of the Ext no. on the phone display. I think this is to do with the PRI setup messages. I have similar networks where is doesn't appear and have crossed referenced the programming with no luck.

The systems are in Australia. I have read a couple of answers on the Net but no one gives an exact answer. Any help would be great.

 

[pronome]

Hi,
on which release is the cs1k running and the protocol on the PRI . if you use MCDN you must enable the Plugin 14
"14 BV70355 MPLR09806 MCDN - ORIG DN IN DISPLAY IS PRECEDED WITH A "H" MCDN
" to remove the "H" in front of your Number .

regards
pronome!

 

[bigindian65]

I've yet to see anyone remove the H

Mato' Was'aka

 

[Matt2010]

Guys,

The Release of the CS1K is Release 6. The protocol is MCDN.

Exactly how is that enabled?

My understanding is through PDT but I had an error message when I entered the command in PDT. Not sure off the top of my head what that was.

Do these plugins need to be loaded, or are they part of the depenancy list?

A mentioned I have a couple of PRI MCDN Networks on some Option11C's that don't have this issue.

Thanks

 

[Firebird Scrambler]

From Release 25.15 onwards a number of Product Improvement Patches (PIs) have been built into the software. These are called PLUGINs

To List/Enable/Disable these PLUGINs use the following commands

First login to pdt. NB All commands are in lowercase

1. To list status of all PLUGINs plp (PLP)
2. To list status of individual PLUGINs plp # (PLP #) where # is the PLUGIN number 0 - 14
3. To enable PLUGIN ple # (PLE #) where # is the PLUGIN number 0 - 14
4. To disable PLUGIN pld # (PLD #) where # is the PLUGIN number 0 - 14

LIST OF PLUGINS

PLUGIN # PRS# Patch # Description
0 BV67946 Wrong Special Dial Tone with NT8D17CA CONF/TDS pack.
1 BV63269 MPLR12002 BRI B-Channels not marked MBSY, When D Channel Drops.
2 BV69389 Automatic Wake-up is turned off if INI occurs.
3 BV69237 MPLR11506 Hotline Enhancement for BASF.
4 BV19192 MPLR01862 After dialling a LSC followed by a DSC the user gets overflow tone
5 BV71211 NRGA is not workingwith Tandem Node & Digit Manipulation.
6 BV28124 MPLR02056 BCS set cannot release from call transfer to Attendant.
7 MP05648 DID with DNIS & IDC cannot call PLDN using SCLU.
8 MP05649 Not possible to CFW a set to PLDN using SCLU.
9 BV41730/40697 Wrong display if Att extends call with announcement.
10 BV42928 MPLR07615 CFW calls to NAS is intercepted to Nite Dn.
11 BV62151 MPLR11339 RAN cannot be accessed via route acod over network.
12 BV63726 MPLR08777 Mtce messages flooding TTY, TTY unusable.
13 BV71206 MCT should be output on answer from 500 set.
14 BV70355 MPLR09806 MCDN - Orig Dn in Display is preceded with "H"

Just enable plugin 14 as shown.


All the best

Firebird Scrambler
Meridian Programmer in the UK

http://www.linkedin.com/in/davidbromley

If it's working, then leave it alone!.

 

[Matt2010]

Thanks for your help. I will give it a go.

 

[NoypiToits]

Hi,

First of all, you must check the software Pkg.409 is activated in the system. This is to enable you to do the plugins command..

Villareal