Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations strongm on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

DSP Daughterboards (DB32 and DB96) No registering on MGC Card

Status
Not open for further replies.
lexer

lexer

Programmer
Jun 13, 2006
432
VE
Hi

I've CS1000E on a CPPM Co-Resident Card Rls 6.0, I've got two MGC with a DB96 on slot 1 and a DB32 slot 2 (each MGC has DB96 and DB32). I've got a MGC on shelf 0 Loop 0 and the other MGC on shelf 0 Loop 1, I configure the MGC's on Element manager and CLI through port 0 in the cards, When I check the status of the cards in LD 32 They show the following status:

STAT - Get card status 0 0 0
----------------------------
00 = UNIT 00 = UNEQ
01 = UNIT 01 = DSBL (TRK)(IPTN UNREG )
02 = UNIT 02 = DSBL (TRK)(IPTN UNREG )
03 = UNIT 03 = DSBL (TRK)(IPTN UNREG )
04 = UNIT 04 = DSBL (TRK)(IPTN UNREG )
05 = UNIT 05 = DSBL (TRK)(IPTN UNREG )
06 = UNIT 06 = DSBL (TRK)(IPTN UNREG )
07 = UNIT 07 = DSBL (TRK)(IPTN UNREG )
08 = UNIT 08 = DSBL (TRK)(IPTN UNREG )
09 = UNIT 09 = DSBL (TRK)(IPTN UNREG )
10 = UNIT 10 = DSBL (TRK)(IPTN UNREG )
11 = UNIT 11 = DSBL (TRK)(IPTN UNREG )
12 = UNIT 12 = DSBL (TRK)(IPTN UNREG )
13 = UNIT 13 = DSBL (TRK)(IPTN UNREG )
14 = UNIT 14 = DSBL (TRK)(IPTN UNREG )
15 = UNIT 15 = DSBL (TRK)(IPTN UNREG )
16 = UNIT 16 = DSBL (TRK)(IPTN UNREG )
17 = UNIT 17 = DSBL (TRK)(IPTN UNREG )
18 = UNIT 18 = DSBL (TRK)(IPTN UNREG )
19 = UNIT 19 = DSBL (TRK)(IPTN UNREG )
20 = UNIT 20 = DSBL (TRK)(IPTN UNREG )
21 = UNIT 21 = DSBL (TRK)(IPTN UNREG )
22 = UNIT 22 = DSBL (TRK)(IPTN UNREG )
23 = UNIT 23 = DSBL (TRK)(IPTN UNREG )
24 = UNIT 24 = DSBL (TRK)(IPTN UNREG )
25 = UNIT 25 = DSBL (TRK)(IPTN UNREG )
26 = UNIT 26 = DSBL (TRK)(IPTN UNREG )
27 = UNIT 27 = DSBL (TRK)(IPTN UNREG )
28 = UNIT 28 = DSBL (TRK)(IPTN UNREG )
29 = UNIT 29 = DSBL (TRK)(IPTN UNREG )
30 = UNIT 30 = DSBL (TRK)(IPTN UNREG )
31 = UNIT 31 = DSBL (TRK)(IPTN UNREG )

Using CLI on MGC I tried the following commands:

ldb> dbhwshow
DB1 model and revision no: NTDW64AA
DB2 model and revision no: NTDW62AA


ldb> mgcinfoshow
Registration Status: Registered on 192.168.10.34
UpTime: 0 days, 18 hours, 17 minutes, 57 seconds

MGC Hostname: MGC
MGC ELAN IP Address: 192.168.10.231
MGC Subnet Mask: 255.255.255.0
MGC Gateway Address: 192.168.10.1

MGC TLAN IP Address: 192.168.1.231
MGC Subnet Mask: 255.255.254.0
MGC Default GW: 192.168.1.201

Primary CS Hostname: Primary_CS
Primary CS IP Address: 192.168.10.34

DB1 NT code: NTDW64AA
DB1 TLAN IP Address: 0.0.0.0
DB1 TN: 000 0 11

DB2 NT code: NTDW62AA
DB2 TLAN IP Address: 0.0.0.0
DB2 TN: 000 0 0

Media Gateway Information
Superloop Shelf: 000 0
TDS Loop: 124
CONF Loop: 125

Active TLAN port: Port 7 = 2T Bottom face plate connector
TLAN port designator:
TLAN set to auto negotiate.

Active ELAN port: Port 6 = 1E Second from bottom face plate connector
ELAN port designator:
ELAN set to auto negotiate.
ELAN security Disabled

ldb> mgcdbshow 0
card 0 not initializedldb>

the mgcinfoshow command shows the DB1 and DB2 are not getting TLAN IP Addresses and the mgcdbshow 0 command shows that the card hasn't been initialized. How can I force the card to initialize?

Any Ideas?

Thanks!!!
 
Sort by date Sort by votes
I experienced the same thing in Rls 5.5. Did you transferred the Node via Element Manager (I am getting an impression of using some wrong terminology). There is an option of importing Node or something like that.

Furthermore, have you made active Elink changes in LD 117?

Go For It Even If It's Impossible !
 
Upvote 0 Downvote
is the MGC registered to the UCM security domain? The DSPs won't go active until that occurs. You can try this command in LD 117 as a temporary workaround. In 117, type "dis transfers secure". That turns off the requirement for the MGC to be in the security domain before the config file will transfer. The mgc will restart and the DSPs should go idle. The issue is that config file won't transfer until the MGC is in the security domain. Thank you Nortel for complicating things even more.
 
Upvote 0 Downvote
Thanks biv343 and fallenangel1 for your answers, I created the UCM but I haven't register to UCM security domain because The customer has a CS1000 rls 4.5 with SSC and I've got a Lab with new card CPPM Co-Res rls 6.0 in my Office I'm testing all to see that is working then change the rls 4.5 for CPPM Co-Res (In the customer). I've have to try in the customer, Because set up the CS1000E to work with the customer domain. I'm going to try LD 117 "dis transfers secure
 
Upvote 0 Downvote
Thanks biv343 I disable transfers secure and now The DB`s cards registered, Do I have to enable secure and register in UCM secure domain or can I just leave the secure disabled?
 
Upvote 0 Downvote
you had something wrong... in the mgc db printout i cannot see the tlan ip address.. so when you register the mgc the configuration is not transferred properly.. did you do the transfer to the cpu after doing the proper configuration in the node? it seems that the answer is no..
 
Upvote 0 Downvote
The "transfers secure" is disabled now and The DB`s cards registered.
If I want to re-enable "transfers secure", How can I make the DB's cards 32 and 96 to register to the secure domain?, I already Configured the primary security server but I'm not using DNS. Can I use the Commands for adding or removing elements from the UCM security domain (Document Security Management Fundamentals NN43001-604) to force the DB's cards on the MGC to register (to UCM security domain)? Or can The DB's cards on MGC work with transfers secure disable without problem?
 
Upvote 0 Downvote
To get my MGC's to register to security domain I used the
reg ucm s
command in LD117 and used the IP address of the primary security server as no DNS also.
 
Upvote 0 Downvote
When I enter the command reg ucm s in LD 117 I receive the following:

=> reg ucm s

SEC037 Security domain membership has been granted. (Centralized authentication is now

enabled.)

DONE !

DONE !

IP address of the Primary Security Server: 192.168.1.34

User Name (UCM): admin
admin

Password (admin):passw0rd!


These elements are registered with the Call Server

MGC 192.168.10.231

MGC 192.168.10.234

Do you want to allow these 2 elements to request security domain membership using your credentials? (Y/N) [N] y
y

Sending messages to 2 elements authorizing them to request security domain membership.

Waiting for status updates from each of the elements...

.................................................................................

TIM000 17:00 28/7/2010 CPU 0

...

SEC102 Element 192.168.10.234 failed to request membership in the security domain, Reas

on FAILED: Upload Element Properties file failed!.

.

SEC102 Element 192.168.10.231 failed to request membership in the security domain, Reas

on FAILED: Upload Element Properties file failed!.

.The Call Server and 0 attached elements successfully requested security domain membership, but 2 elements failed.

CS is reporting the following messages (DSP are waiting for waiting for mgcdb.xml file):

28/07/2010 15:48:43 LOG0004 tMgcVgwAppStart: DSP DBs are present, waiting for mgcdb.xml from Primary Call Server
28/07/2010 15:48:43 SEC0105 USR=initialization, EVT=global port access state change to off, RESULT=success
28/07/2010 15:48:43 LOG0006 applStart: portAccessInit initialization succeeded
28/07/2010 15:48:43 LOG0006 applStart: securityDomainElemPropValueSet initialization succeeded
28/07/2010 15:48:58 LOG0004 tMgcVgwAppStartRetry: DSP DBs are present, waiting for mgcdb.xml from Primary Call Server
28/07/2010 15:49:13 LOG0004 tMgcVgwAppStartRetry: DSP DBs are present, waiting for mgcdb.xml from Primary Call Server

The MGC 0 0 and the MGC 0 1 are registered but the DB's 32 and 96 not:

STAT - Get card status 0 0 0
----------------------------
00 = UNIT 00 = UNEQ
01 = UNIT 01 = DSBL (TRK)(IPTN UNREG )
02 = UNIT 02 = DSBL (TRK)(IPTN UNREG )
03 = UNIT 03 = DSBL (TRK)(IPTN UNREG )


If I disable transfers secure on Ld 117 "dis transfers secure" the DB's 32 and 96 in both MGC get registered:

.stat 00 0 0


00 = UNIT 00 = UNEQ

01 = UNIT 01 = IDLE (TRK)(IPTN REG )

02 = UNIT 02 = IDLE (TRK)(IPTN REG )

03 = UNIT 03 = IDLE (TRK)(IPTN REG )


.stat 0 1 0


00 = UNIT 00 = UNEQ

01 = UNIT 01 = IDLE (TRK)(IPTN REG )

02 = UNIT 02 = IDLE (TRK)(IPTN REG )

03 = UNIT 03 = IDLE (TRK)(IPTN REG )

What question can I work with transfers secure disable for MGC cards, Or Do I have to enable transfers secure?
 
Upvote 0 Downvote
When I enter the command reg ucm s in LD 117 I receive the following:


=> reg ucm s

SEC037 Security domain membership has been granted. (Centralized authentication is now

enabled.)

DONE !

DONE !

IP address of the Primary Security Server: 192.168.1.34

User Name (UCM): admin
admin

Password (admin):passw0rd!


These elements are registered with the Call Server

MGC 192.168.10.231

MGC 192.168.10.234

Do you want to allow these 2 elements to request security domain membership using your credentials? (Y/N) [N] y
y

Sending messages to 2 elements authorizing them to request security domain membership.

Waiting for status updates from each of the elements...

.................................................................................

TIM000 17:00 28/7/2010 CPU 0

...

SEC102 Element 192.168.10.234 failed to request membership in the security domain, Reas

on FAILED: Upload Element Properties file failed!.

.

SEC102 Element 192.168.10.231 failed to request membership in the security domain, Reas

on FAILED: Upload Element Properties file failed!.

.The Call Server and 0 attached elements successfully requested security domain membership, but 2 elements failed.

CS is reporting the following messages (DSP are waiting for waiting for mgcdb.xml file):

28/07/2010 15:48:43 LOG0004 tMgcVgwAppStart: DSP DBs are present, waiting for mgcdb.xml from Primary Call Server
28/07/2010 15:48:43 SEC0105 USR=initialization, EVT=global port access state change to off, RESULT=success
28/07/2010 15:48:43 LOG0006 applStart: portAccessInit initialization succeeded
28/07/2010 15:48:43 LOG0006 applStart: securityDomainElemPropValueSet initialization succeeded
28/07/2010 15:48:58 LOG0004 tMgcVgwAppStartRetry: DSP DBs are present, waiting for mgcdb.xml from Primary Call Server
28/07/2010 15:49:13 LOG0004 tMgcVgwAppStartRetry: DSP DBs are present, waiting for mgcdb.xml from Primary Call Server


The MGC 0 0 and the MGC 0 1 are registered but the DB's 32 and 96 not:

STAT - Get card status 0 0 0
----------------------------
00 = UNIT 00 = UNEQ
01 = UNIT 01 = DSBL (TRK)(IPTN UNREG )
02 = UNIT 02 = DSBL (TRK)(IPTN UNREG )
03 = UNIT 03 = DSBL (TRK)(IPTN UNREG )


If I disable transfers secure on Ld 117 "dis transfers secure" the DB's 32 and 96 in both MGC get registered:

.stat 00 0 0


00 = UNIT 00 = UNEQ

01 = UNIT 01 = IDLE (TRK)(IPTN REG )

02 = UNIT 02 = IDLE (TRK)(IPTN REG )

03 = UNIT 03 = IDLE (TRK)(IPTN REG )


.stat 0 1 0


00 = UNIT 00 = UNEQ

01 = UNIT 01 = IDLE (TRK)(IPTN REG )

02 = UNIT 02 = IDLE (TRK)(IPTN REG )

03 = UNIT 03 = IDLE (TRK)(IPTN REG )

Can The PBX works with transfers secure disable for MGC cards, Or Do I have to enable transfers secure?
 
Upvote 0 Downvote
SEC102 Element 192.168.10.234 failed to request membership in the security domain, Reason FAILED: Upload Element Properties file failed!.


SEC102 Element 192.168.10.231 failed to request membership in the security domain, Reason FAILED: Upload Element Properties file failed!.

I think the MGC are not registered.

Pls Print

LD 117
stat ucmsec system



Meridian, Callpilot, CCM (Symposium) from Germany
 
Upvote 0 Downvote
Thanks M1spezi, I enter "stat ucmsec system" in LD 117 and The MGC cards are not registered (Although The MGC´s display show the the cards as registered):

>ld 117

=> stat ucmsec system
MGC 192.168.10.231 UNREGISTERED
MGC 192.168.10.234 UNREGISTERED



What can I try to make them to register?

I dont know why The MGC's are reporting this message:

DSP are waiting for waiting for mgcdb.xml file


Can I disable secure transfers (disable sFTP in LD 117)?

I read that the secure transfers is for MGC Upgrade (Manual NN43001-604)

 
Upvote 0 Downvote
First!!!!!

Install the latest deplist to your callserver.

2.

After => reg ucm s you will have a " : " behind the Tlan Ip Adress of your Sec Domain. Type here the ELAN IP ADRESS of your UCM Secutity Server.

=> reg ucm s



IP address of the Primary Security Server: 192.168.1.34:







Meridian, Callpilot, CCM (Symposium) from Germany
 
Upvote 0 Downvote
Sorry should have specified it was the ELAN IP Address of the Primary Security Server

LD 117
reg ucm s
Then was asked to enter ELAN IP Address of Primary Security Server
Then my PWD2 Login.

Then, in my case, all 4 MGC&VTRKs then registered.
 
Upvote 0 Downvote
Could you please tell me the deplist names for the Callserver, I was searching in Nortel and there are several pep's for CS1000E rls 6.0.

Thanks!!!
 
Upvote 0 Downvote
Have you tried clearing the MGC cards and then re-entering the IP information.
Clear the IP, boot the card and then re-enter the IP info.
 
Upvote 0 Downvote
Yes, I already tried clearing the MGC cards
 
Upvote 0 Downvote
Reseat MGC card and watch it boot.
When "DSP are waiting for mgcdb.xml file" appears type <CTRL> OAM
AT > type mgcsetup and re-enter IP info.
When it asks to reboot say yes and it should sync up and register.
 
Upvote 0 Downvote
Finally I could make MGC's cards to join the UCM security Domain, I did the following:

*From port 0 on the MGC I entered the command: joinSecDomain, then I was asked to enter the ELAN CallServer Ip Address.
*Second in the UCM --> IPSec: I added manually the MGC then Syncronize and Activate (force).


Now I see that the MGC channels as IDLE.

From MGC CLI:

ldb> mgcinfoshow
Registration Status: Registered on 192.168.10.34
UpTime: 0 days, 00 hours, 16 minutes, 28 seconds

MGC Hostname: MGC01
MGC ELAN IP Address: 192.168.10.234
MGC Subnet Mask: 255.255.255.0
MGC Gateway Address: 192.168.10.1

MGC TLAN IP Address: 192.168.1.234
MGC Subnet Mask: 255.255.255.0
MGC Default GW: 192.168.1.201

Primary CS Hostname: co-res-cppm
Primary CS IP Address: 192.168.10.34

DB1 NT code: NTDW64AA
DB1 TLAN IP Address: 192.168.1.222
DB1 TN: 000 1 11

DB2 NT code: NTDW62AA
DB2 TLAN IP Address: 192.168.1.223
DB2 TN: 000 1 0

Media Gateway Information
Superloop Shelf: 000 1
TDS Loop: 126
CONF Loop: 127

Active TLAN port: Port 7 = 2T Bottom face plate connector
TLAN port designator: 2T
TLAN set to auto negotiate.

Active ELAN port: Port 6 = 1E Second from bottom face plate connector
ELAN port designator: 1E
ELAN set to auto negotiate.
ELAN security Enabled, level is Optimized Security

From LD 117:

>ld 117


=> stat ucm s

MGC 192.168.10.231 REGISTERED
MGC 192.168.10.234 REGISTERED


Thanks for your answers!!!
 
Upvote 0 Downvote
Status
Not open for further replies.

Similar threads

jpanzer
  • Locked
  • Question
Difference between NTAK11 and NT1P70AA cabinets - no TTY output
Replies
2
Views
173
jpanzer
jpanzer
CentralJIM
  • Locked
  • Question
no caller ID on PRI external call
Replies
5
Views
225
CentralJIM
CentralJIM
HollTel
  • Locked
  • Question
TTY not working on a CS1K Rls. 7.0
Replies
2
Views
242
HollTel
HollTel
BSmith01
  • Locked
  • Question
Nortel MerMail EC Rls 12 issue with Utility Card NT6P42AA
Replies
4
Views
149
BSmith01
BSmith01
Trason
  • Question
e911 on rls 7 where to start
Replies
2
Views
244
bignose21
bignose21

Part and Inventory Search

Sponsor

Back
Top