Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

  • Congratulations strongm on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

drivers softwre i formated my server nice

Status
Not open for further replies.

wladimiravila

IS-IT--Management
Apr 30, 2010
3
CO
hi good day
I formated my server i need driver from my server nice, pci card, software, my OS is winXP

regards1
 
hi i dont know mi version
my board card number is NICE SYSTEM LTDA ALI IV

i could should is 7.5, the operative system is xp

regards!
 
Hi

When you install the logger sw there is a message. Please wait until all boards are detected.
There is a popup for each card.
Connect to windows uppdate -> Not at this time
Yes Install automaticly
This software is not .... Install anyway -> Yes
 
Hi to all!

Sorry to wladimiravila for putting my question inside his/her thread but I think they are nearly the same.

Can someone please explain in detailed steps which is the procedure to install a new system from the very begining? (format the existing one). How to have curent licenses stored in order to activate the system after the installation. My system is Nice call focus 3

Thank You in advance!
 
I have also the recovery kit (CD 1 - 4).
May someone tell the steps needed for a successful installation?

Thank you in advance!
 
There should be software that came with the logger. In there is a config file, probably on the 'Enhanced SW' disk. On it should be a folder with all numbers. Inside there should be a summary.doc. If you can get the contents of that, we should be able to tell you what you have.
 
Thanks VPITech!

I browsed all the four CD, part of recovery kit.
They are labeled as NiceCall Focus 3 Image CD WinXP 1-4.
Inside each of them were three files; two identic at each CD: ghost, ghstwalk and NCH3LS.gho, NCF3L001.ghs up to NCF3L003.ghs at each CD.

May I have some further feedback?

Thank You
 
Hi VPITech,
Yes I found another box, except the one for recovery, which contains the follwing CD:

1. NiceCall Focus3 NiceLog Logger
2. NiceCall Focus3 Nice Applications
3. NiceCall Focus3 SW Core Components
4. NiceCall Focus3 SNMP Alarming
5. NiceCall Focus3 SQL Auto Setup
6. NiceCall Focus3 User's Documentation CD V8.9
 
There it is. On the Call Focus 3 Documentation CD, there will be a PDF on how to restore your system from total catastrophic failure. I had to rebuild my system about 6 times before I got it right. If I know it to be correct, you'll have a manual that doesn't make a whole lot of sense in places, but it's the place to start. A little patience and some note-taking, and you'll get yourself back up.

Typical install is:
XP Restore Disks -> SQL -> Logger Software -> CLS. There are hotfixes and other things to be mindful of.

Good luck with it.
 
Hi,

I've just installed Nice Digital Logger 9.6.02.22 and HotFix ETAI3 01.00.05. The problem is that the Ntlogger can't start because the ETAI driver can't initialize

"FATAL: ETAI3_DspBoot: DriverStatus fail <Sta, 0> 3 0 12/1/2010 3:31:32 PM
FATAL: BootEtai3DspsAndCheckCrc: failed in ETAI3_DspBoot <DspFileName, BoardId, DspNumber> D:\NTLogger\Logger\Firmware\etai3.DSP 0 3 12/1/2010 3:31:32 PM
FATAL: ETAI3_DspWriteSyncCommand: DriverStatus fail <Sta, 0> 4 0 12/1/2010 3:31:34 PM
FATAL: BootEtai3DspsAndCheckCrc: failed in ETAI3_ReadCrc 0 0 12/1/2010 3:31:34 PM
FATAL: BootEtai3DspsAndCheckCrc: Failure in DSP Boot, <BoardId, DspNumber> 0 3 12/1/2010 3:31:34 PM
FATAL: ETAI3_InitClockMaster: Etai3 clock master failed to initialize <Status, 0> 53 0 12/1/2010 3:31:34 PM "

From Device manager the driver seems to be ok. I can provide more logs if it's necesary

Where can I find a driver ?

Thank you

 
shutdown the logger and reseat the etai card.check the summary.doc file in d:\ntlogger\logger\config folder to make sure what is in system matches what hardware is in recorder.

Try reseat of card/h100 cable first and check cable terminations etc and then power up to see if this resolves your issue.
 
hi celtic123

reseat the etai card
done this, move it to another PCI slot ( same result) and move it back
summary doc.
ETAI3
=====
Number Of EATI3 Boards = 1
Instant callback = NO
Board 0
.....

reseat of card/h100 - done it, no effect

is there any order of installing Logger software and hot fix ? ex.
1. dotnetfx 2. Etai3 HF 3. Logger setup
the etai3 card driver is included in logger setup ?

another detail. The Syststr tester shows tha thecard is ok but every time I reset the server the card driver is not initialized

thank you for your help,
iulian
 
hi 9.06.02 is an old service pack. i would load latest which includes this hf its service pack 5 can be downloaded from extranice.

etai driver is installed as part of logger setup.

If you could send us the log from d:\ntlogger\logger\log latest one post a reboot?
 
the log is quite long I don't know if it's ok to post it here ( may be an e-mail ?). I've looked on extranice site but found nothing related to Etai3.
Meanwhile I found that the Etai card has the same IRQ with Adif4 card, I will try to fix it, but I'm not sure that this is the problem.
 
Status
Not open for further replies.

Part and Inventory Search

Sponsor

Back
Top