CMMap message in monitor

[Spekkert]

Hey Guys,

I did a new install. everything works but I get a continious message in my monitor which i dont know what it means:

103383845mS CMMap: a=12.24 b=0.0 B1
103383845mS CMMap: a=12.25 b=0.0 B1
103384324mS CMMap: a=12.19 b=0.0 B0
103384324mS CMMap: a=12.20 b=0.0 B0
103384324mS CMMap: a=12.21 b=0.0 B0
103384325mS CMMap: a=12.22 b=0.0 B0
103384325mS CMMap: a=12.23 b=0.0 B0
103384325mS CMMap: a=12.24 b=0.0 B0
103384325mS CMMap: a=12.25 b=0.0 B0
103384804mS CMMap: a=12.19 b=0.0 B1
103384804mS CMMap: a=12.20 b=0.0 B1
103384804mS CMMap: a=12.21 b=0.0 B1
103384804mS CMMap: a=12.22 b=0.0 B1
103384804mS CMMap: a=12.23 b=0.0 B1
103384804mS CMMap: a=12.24 b=0.0 B1
103384805mS CMMap: a=12.25 b=0.0 B1
103385284mS CMMap: a=12.19 b=0.0 B0

Does anybody have an idea?

Gr

 

[intrigrant]

B0 = busy tone off
B1 = busy tone on
a= & b= hardware address depending on the system
for a ip406v2 12 = exp.mod 3

 

[Spekkert]

It's a 406v2 indeed, software 4.2.20.
Epx 3 is Phone 30.

Is this a problem?

 

[intrigrant]

Could be a cabling problem or the PSU is rubbish.
Start with swapping the blue cable and the PSU if it does not help then swap the unit.
If it still does not help then the cabling to the extensions give problems ( earth wire? )

 

[drhex2000]

Would like to rehash the issue
IP500 4.2 showing continous
CMMap: a=4.24 b=0.0 B0
Power cycling doesn't do anything, calling in/out is broken.
Can anybody point me to a legend/pinpoint the problem component?
Thanks,
Florian

 

[amriddle01]

Did you do any of intigrants suggestions? Are you using the correct cable for the expansion module?

ACS - IP Office Implement

"What the Crocodile Hat....was that?

 

[drhex2000]

Sorry, should have added that - there is no expansion module on this box:

21327489mS CMMap: a=4.24 b=0.0 B1
21327739mS CMMap: a=4.24 b=0.0 B0
21327846mS PRN: +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
21327846mS PRN: + loader: 1.3
21327846mS PRN: + cpu: id 2 board d0 pld 17 type c10 options 2
21327846mS PRN: + fpga: id 1 issue 1 build 817
21327846mS PRN: +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
21327846mS PRN: ++++++++++++++++++++ LIST OF MODULES ++++++++++++++++++++
21327846mS PRN: +------------------------------------------------------------
21327847mS PRN: + Slot 1: Base DIGSTA8 Board=0x12 PLD=0x06
21327847mS PRN: + Mezzanine BRI8 Board=0x01 PLD=0x08
21327847mS PRN: +------------------------------------------------------------
21327847mS PRN: + Slot 2: Base PHONE8 Board=0x03 PLD=0x03
21327847mS PRN: + Mezzanine BRI8 Board=0x01 PLD=0x08
21327847mS PRN: +------------------------------------------------------------
21327847mS PRN: + Slot 3: Base PHONE8 Board=0x03 PLD=0x03
21327848mS PRN: + Mezzanine ATM4 Board=0x03 PLD=0x07
21327848mS PRN: +------------------------------------------------------------
21327848mS PRN: + Slot 4: Base PHONE8 Board=0x03 PLD=0x03
21327848mS PRN: + Mezzanine NONE
21327848mS PRN: +------------------------------------------------------------
21327848mS PRN: +++++++++++++++++ END OF LIST OF MODULES +++++++++++++++
21327989mS CMMap: a=4.24 b=0.0 B1
21328239mS CMMap: a=4.24 b=0.0 B0

Must be one of the internal cards - suspect the ATM, as outside world is gone.

Florian

 

[drhex2000]

And to make me look really bad: This is 5.0(8). And no, I did not upgrade, was delivered like this into my 4.2 environment.