CLID not displaying on phones - C1000

[babytech2009]

Hello,

I have created a new entry and tried testing with both settings for entry 2 but no avail. Still shows as unavailable.
Per documents and this site I did not see anything that would guide me differently or where to look to see why it is not working.


ENTRY 2
HNTN 703
ESA_HLCL
ESA_INHN NO
ESA_APDN NO>>>>>>>>>Prior to this setting I had this set to yes. _ When I have the users test it still shows as unavailable.
HLCL 336
DIDN YES
DIDN_LEN 0
HLOC
LSC
CLASS_FMT DN


Here is one of the 6 phones it is on.

KEY 00 SCR 8024 2 MARP
CPND
NAME ]
XPLN 27
DISPLAY_FMT FIRST,LAST
01 SCR 7024 D MARP >>>>>> someone said to use 2 instead of D for the entry here as well.


I am hoping I do not need to create a entry for each phone. Any ideas?


Thanks

 

[Firebird Scrambler]

In the UK, we tend to use it only with PRI circuits

The HNTN is the area code and the HLCL is part of the local DID number. The setup might well be different in your country. We also sometimes have to delete the initial "0" in the HNTN number.

REQ: CHG
TYPE: NET

TYPE NET_DATA
CUST 0
OPT
AC2
FNP
CLID YES
SIZE 256 (DEFAULT SETTING)
INTL 44 (UK INTERNATIONAL CODE)
ENTRY 0 )
HNTN 01823 )
HLCL 34 ) FOR KEY DDI No (i.e 01823 34 5500)
DIDN YES )
HLOC )
LSC )
ENTRY 0 SAVED!
ENTRY 1 )
HNTN 01823 )
HLCL 326800 ) FOR ANOTHER No TO BE SENT (i.e 01823 326800)
DIDN NO )
HLOC )
LSC )
ENTRY 1 SAVED!
ENTRY 2 )
HNTN )
HLCL ) FOR HOME LOCATION CODE TO BE SENT ON PRIVATE NETWORKS
DIDN ) WITH KEY No (i.e 123 5500)
HLOC 123 )
LSC )
ENTRY 2 SAVED!
ENTRY 3 )
HNTN )
HLCL ) FOR LOCAL STEERING CODE WITH KEY No (i.e 456 5500)
DIDN )
HLOC )
LSC 456 )
ENTRY 3 SAVED!
ENTRY
ISDN
PNI
PINX_DN
MBG
BSGC
PFX1
PFX2
HLOC
LSC
RCNT
PSTN
TNDM
PCMC
SATD
OCLI
TIDM
DASC
ROPT
DITI
TRNX
EXTT
FTOP
APAD
VNR
NIT
NAS ATCL
NAS ACTV
FOPT
CNDN
CNAT
CNIP

>LD 21

REQ: PRT
TYPE: CLID
CUST 0
SIZE 256
RNGE

INTL 44

ENTRY 0
HNTN 01823
HLCL 34
DIDN YES
HLOC
LSC

ENTRY 1
HNTN 01823
HLCL 326800
DIDN NO
HLOC
LSC

ENTRY 2
HNTN
HLCL
DIDN YES
HLOC 123
LSC

ENTRY 3
HNTN
HLCL
DIDN YES
HLOC
LSC 456

ASSIGNING TO AN ANALOGUE SET
********* ** ** ******** ***

CLID TABLE 0 IS ALLOCATED TO ALL SETS BY DEFAULT

LD 10
REQ CHG
TYPE: 500
TN 4 0 7 0
ECHG YES
ITEM DN 2001 1
MARP
CPND
VMB
ITEM

REQ: PRT
TYPE: 500
TN 4 0 7 0
DATE
PAGE
DES

DES FAX
TN 004 0 07 00
TYPE 500
CDEN 4D
CUST 0
WRLS NO
DN 2001 1 MARP (NOTE CLID TABLE 1 FOLLOWING DN No)
CPND
CPND_LANG ROMAN (NAME IS NOT LOST WHEN CLID TABLE IS CHANGED)
NAME MODEM /FAX
XPLN 27
DISPLAY_FMT FIRST,LAST
AST NO
IAPG 0



Firebird Scrambler
Nortel Meridian 1 / Succession and BCM / Norstar Programmer in the UK
Advance knowledge on BCM support

http://www.linkedin.com/in/davidbromley

 

[babytech2009]

Thank you Firebirdscrambler.

They are wanting to show the whole 10 digit phone number.

 

[babytech2009]

This is what I see when I do a TRAC on the line. when they call to me. it is still not showing the CLID

TN 020 0 07 11
KEY 0 SCR MARP ACTIVE TN 020 0 07 11

ORIG TN 020 0 07 11 KEY 0 SCR MARP CUST 0 DN 8029 TYPE 3904
SIGNALLING ENCRYPTION: INSEC
TERM TN 018 22 TIE RMBR 1 70 OUTGOING TRUNK CALL
TDTN 16 SLOT 24 PTY SLOT 10
DIAL DN 703894733102291
MAIN_PM DIAL AUX_PM NOOUTPULSE
TALKSLOT ORIG 5 TERM 10
EES_DATA:
NONE
QUEU NONE
CALL ID 0 5249

 

[KCFLHRC]

One thing you need to keep in mind, your carrier has to allow you to send the DID # out also.

 

[babytech2009]

we have it going out the local so the caller id now shows but no we are unable to get them to use the long distance code to place ld calls.