Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

  • Congratulations strongm on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

CIL NIU2

Status
Not open for further replies.

gosad

Technical User
Sep 15, 2008
7
PL
hello

I use md110 bc11 and i try run cil on niu2 rs232.
My ioddp;
<IODDP;
I/O DEVICE DATA
NODE IODEV/SUBFS BPOS/EQU I/O-BUS TYPE/USAGE STATUS AUTH
SYSN - 001-0-50 - - IN SERVICE
SYSN SYSDISK1 001-0-50-0 MASTER TOSHIBA IN SERVICE
SYSSUBFS11
SYSSUBFS21
SYSN SYSTERMINAL 001-0-50-1 - MML - 7
SYSN MML2 001-0-50-2 - MML - 7
SYSN CIL-1 001-0-50-3 - OUT IN SERVICE
SYSN CILNET 001-0-50-4 - NETWORK/OUT IN SERVICE
SYSN MMLETH 001-0-50-4 - NETWORK/MML - 7
SYSN MMLETH2 001-0-50-4 - NETWORK/MML - 7
END

if i enter
CLDFI:FILE=CIL,IODEV=CIL-1,USER=CIL-1;
NOT ACCEPTED
NIU
NOT ALLOWED

I try USER=NONE and cil nertwork connected answer is same always
NOT ACCEPTED
NIU
NOT ALLOWED

If you have any idea what to check on this problem, please write !

Thanks
I'am new on this forum and sory fo my english
 
CLFDI:IODEV=SMDR,FILE=SMDR,USER=CIL1;

i hope this will work
 
CLDFI:IODEV=SMDR,FILE=SMDR,USER=CIL1;
NOT ACCEPTED
USER
NOT IN RANGE

After change of user

CLDFI:IODEV=SMDR,FILE=SMDR,USER=CIL-1;
NOT ACCEPTED
NIU
NOT ALLOWED

CLDFI:IODEV=SMDR,FILE=SMDR,USER=NONE;
NOT ACCEPTED
NIU
NOT ALLOWED

any idea
 
Do you have CIL on SIU active in your system?

You cannot run CIL on SIU and on NIU in one system.
 
please print current status:

CLDFP;
EDEQP;
CLINP;

/Daddy

-----------------------------------------------------
What You See Is What You Get
Never underestimate tha powah of tha google!
 
print result

<CLDFP;
FILE ADMINISTRATION DATA
END

<EDEQP;
NOT ACCEPTED
DEV
NOT INITIATED
<CLINP;
CALL LOGGING DATA
CALL LOGGING MODE: NOT ACTIVATED
MOBILITY LOGGING MODE: NOT ACTIVATED
HEADER FORM DMPSIZ DISCR IN SERVICE LOGABN HRTBT
CIL 2 1 0 YES NO NO
ORIG DIAL TIME
ALL 0 ALL
ALL 199 ALL
ALL 198 ALL
ALL 197 ALL
ALL 196 ALL
ALL 191 ALL
ALL 890 ALL
DIR LIM BPOS EVENT


END

I was have card SIU bad it broken and fing i was remov it on system.
 
Try sconfigurare fully cyl including the door on NIU.
And this re-configuration ...
IOEQI:IODEV=ACAB,EQU=1-0-50-3,USAGE=OUT;
CLDFI:FILE=CAB,USER=NONE,IODEV=ACAB,PRIO=C;
CLOHI:FILE=CAB,FORM=2,DMPSIZ=1,DISCR=0,LOGABN=N0,LOGFAL=0;
CLODI:FILE=CAB;
CLODI:FILE=CAB,DIAL=0;
CLTGI;
 
I have checked way it and I search solution

<IOEQI:IODEV=ACAB,EQU=1-0-50-3,USAGE=OUT;
EXECUTED

<CLDFI:FILE=CAB,USER=NONE,IODEV=ACAB,PRIO=C;
NOT ACCEPTED
NIU
NOT ALLOWED
 
please give the printout of LIDAP;

-----------------------------------------------------
What You See Is What You Get
Never underestimate tha powah of tha google!
 
<lidap;

EIC=01-3688
SEQUENCE ID=3

PORT LICENCES

LICENCE TAG FAL ALLOWED USED
ACD-AGENT FAL104525 10 0
ANALOGUE-EXTENSION FAL104451 480 349
ANALOGUE-EXTENSION-CLIP FAL1046191 0 0
ANCD-V24-INTERFACE FAL104526 2 0
APP-LINK-INTERFACE FAL104536 0 0
BASE-STATION-DECT FAL104520 0 0
CAS-EXTENSION FAL104455 0 0
CCM-ETH-INTERFACE FAL104531 0 0
CCM-V24-INTERFACE FAL104530 1 0
CIL-HDU-INTERFACE FAL104710 0 0
CORDLESS-EXTENSION FAL104454 0 0
CTT-EXTENSION FAL104457 0 0
DIGITAL-EXTENSION FAL104452 472 449
DTMF-RECEIVER-MOB-EXT FAL1043610 0 0
DUPLICATED-CS FAL104491 0 0
EM-ETH-INTERFACE FAL104538 0 0
EM-V24-INTERFACE FAL104537 2 0
EXTERNAL-LINE-APNSS FAL104467 0 0
EXTERNAL-LINE-CAS-ANA FAL104461 218 28
EXTERNAL-LINE-CAS-DIG FAL104462 0 0
EXTERNAL-LINE-CCSS7 FAL104705 0 0
EXTERNAL-LINE-DASS FAL104463 0 0
EXTERNAL-LINE-DPNSS FAL104465 0 0
EXTERNAL-LINE-H323 FAL1042179 0 0
EXTERNAL-LINE-H323-SERV FAL1043611 0 0
EXTERNAL-LINE-ISDN-NET FAL104507 30 0
EXTERNAL-LINE-ISDN-USR FAL104464 210 90
EXTERNAL-LINE-QSIG FAL104466 0 0
FIXED-REMOTE-EXTENSION FAL1040524 0 0
FREESEATING FAL1040050 0 0
GENERIC-EXT-SMS FAL104708 0 0
GROUP-SWITCH-LINK FAL104492 9 7
IP-EXTENSION FAL104706 0 0
IS-ETH-INTERFACE FAL104533 0 0
IS-V24-INTERFACE FAL104532 1 0
ISDN-TERMINAL-INTERFACE FAL104453 0 0
LINE-INTERFACE-MODULE FAL1040049 5 3
MOBILE-EXTENSION FAL1040525 0 0
OM-ETH-INTERFACE FAL104540 3 2
OM-V24-INTERFACE FAL104539 4 1
OPERATOR-EXTENSION FAL104456 4 3
PAGING-LOOP FAL104518 8 0
PAGING-PARALLEL FAL104519 8 0
PAGING-SERIAL FAL104517 8 0
PERSONAL-NUMBER-USER FAL104472 0 0
RADIO-EXTENSION FAL1040285 0 0
REPEAT-IND-DIV-USER FAL104471 0 0
RVA-EXTERNAL FAL104487 12 0
RVA-INTERNAL FAL104486 12 0
SMDR-ETH-INTERFACE FAL104489 0 0
SMDR-V24-INTERFACE FAL104488 5 0
VCU-FAX-III-PORT FAL104512 12 0
VM-ETH-INTERFACE FAL104535 0 0
VM-V24-INTERFACE FAL104534 3 0
VOICE-MAILBOX FAL104470 0 0
VOICE-PORT FAL104547 0 0
VOICE-SYSTEM FAL104546 0 0
VOIP-ETH-INTERFACE FAL104707 0 0

SYSTEM LICENCES

LICENCE TAG FAL ALLOWED
A-NUMBER-DISPLAY-ATS FAL1041997 NO
ANCD-FEATURE FAL104545 YES
DISA-NUMBER FAL104484 YES
DUPLICATED-GS FAL104524 NO
HOSPITALITY-APPLICATION FAL104709 NO
NET-SERVICES FAL104506 YES
ORIGINAL-A-NUMBER FAL1040278 NO
QSIG-CALL-OFFER FAL1041985 NO
ROUTING-SERVER-CLIENT FAL1046193 NO
ROUTING-SERVER-SERVER FAL1046192 NO
TRAFFIC-MEASUREMENT FAL104485 YES
END
 
I restarted the program without results .
 
did you tried to delete all related call logging definations? Like:
CLTGE;
CLODE:FILE=CIL;
CLOHE:FILE=CIL;
CLDFE:FILE=CIL,USER=XXX;
IOEQE:IODEV=XXXX; and
IOEQI:IODEV=ACAB,EQU=1-0-50-3,USAGE=OUT;
CLDFI:FILE=CAB,USER=NONE,IODEV=ACAB,PRIO=C;
CLOHI:FILE=CAB,FORM=2,DMPSIZ=1,DISCR=0,LOGABN=N0,LOGFAL=0;
CLODI:FILE=CAB;
CLODI:FILE=CAB,DIAL=0;
CLTGI;
 
Thanks for assistance it work ok .
Formerly i wasn't erase all call criteria.
 
Status
Not open for further replies.

Part and Inventory Search

Sponsor

Back
Top