CDR Output 1

[carldest]

I have an Option 11 that I have "front ended" with another switch. I have a trunk route that is two T1's connecting the two switches. The option 11 has analog trunks in another route that all outbound traffic is routed on. When a station on the 11 dials an extension in the other switch it is routed over the T1 route.

I have CDR set the exact same on both routes. I get CDR output on the CTY port for any call on the T1 route but no output on the local analog trunk route.

Any ideas?

Thanks in advance

 

[tamoukh]

can you send what you did on LD 15 & LD 16?

 

[carldest]

Here is cdr part of cdb

CDR_DATA
CDR YES
IMPH NO
OMPH NO
AXID NO
TRCR NO
CDPR NO
ECDR YES
BDI NO
PORT 2
BCAP NO
CHLN 0
FCAF NO

TYPE RDB
CUST 00
DMOD
ROUT 9
DES
TKTP COT
NPID_TBL_NUM 0
PRIV NO
SAT NO
RCLS EXT
VTRK NO
NODE
DTRK NO
PTYP ACO
AUTO YES
ICOG IAO
RANX NO
SRCH LIN
TRMB YES
STEP
ACOD 7109
CPP NO
TARG 10
CLEN 1
BILN NO
OABS
TIMR ICF 512
OGF 640
EOD 1920
DSI 34944
NRD 10112
DDL 70
OOD 1
ODT 4096
RGV 640
FLH 510
GRD 896
SFB 3
CRD 512
TFD 0
LEXT 100
SST 3 0
NEDC ETH
FEDC ETH
CPDC NO
SPCT IMM
HOLD 02 02 40
SEIZ 02 02
RGFL 02 02
RVSD 08 31
ILLR 02 02
DRNG YES
NDRI 00
CDR YES
INC YES
LAST NO
QREC NO
OAL YES
AIA NO
OAN YES
OPD NO
CDRX NO



PAGE 002

SCH2017

NATL YES
MUS YES
MRT 23
MR NO
MANO NO
EQAR NO
FRL 0 0
FRL 1 0
FRL 2 0
FRL 3 0
FRL 4 0
FRL 5 0
FRL 6 0
FRL 7 0
TTBL 0
ATAN NO
OHTD NO
PLEV 2
MCTS NO
ALRM NO
ART 0
SGRP 0
AACR NO

TYPE RDB
CUST 00
DMOD
ROUT 23
DES
TKTP MUS
NPID_TBL_NUM 0
VTRK NO
NODE
ICOG OGT
SRCH LIN
STEP
BDCT NO
ACOD 7123
TARG
CLEN 1
OABS
TIMR ICF 512
OGF 512
EOD 13952
DSI 34944
NRD 10112
DDL 70
ODT 4096
RGV 640
GRD 896
SFB 3
SST 5 0
NEDC ETH
FEDC ORG
HOLD 02 02 40
SEIZ 02 02
RGFL 02 02
CDR NO
MUS NO
TTBL 0
OHTD NO


PAGE 003

ALRM NO
SGRP 0
AACR NO

TYPE RDB
CUST 00
DMOD
ROUT 49
DES CORAL
TKTP TIE
NPID_TBL_NUM 0
ESN NO
CNVT YES
DDMI 0
ATDN 0
SAT NO
RCLS INT
VTRK NO
NODE
DTRK YES
BRIP NO
DGTP DTI
DSEL VCE
PTYP DTT
AUTO NO
DNIS NO
ICOG IAO
SRCH LIN
TRMB YES
STEP
ACOD 7149
TARG 01
CLEN 1
BILN NO
OABS
INST
IDC NO
DCNO 0 *
NDNO 0
DEXT NO
ANTK
SIGO STD
STYP SDAT
TIMR ICF 512
OGF 512
EOD 3968
DSI 34944
NRD 10112
DDL 70
ODT 4096
RGV 640
GRD 896
SFB 3
TFD 0
SST 5 0
NEDC ETH
FEDC ETH
CPDC NO
DLTN NO
HOLD 02 02 40
SEIZ 02 02
SVFL 02 02
DRNG NO


PAGE 004

CDR YES
INC YES
LAST NO
QREC NO
OAL YES
AIA NO
OAN YES
OPD NO
CDRX NO
NATL YES
MUS YES
MRT 23
RACD NO
MANO NO
EQAR NO
FRL 0 0
FRL 1 0
FRL 2 0
FRL 3 0
FRL 4 0
FRL 5 0
FRL 6 0
FRL 7 0
AUTH NO
TTBL 0
ATAN NO
OHTD NO
PLEV 2
ALRM NO
ART 0
SGRP 0
AACR NO


I have been working on Nortels since Rls 1 (my certification was from March of 1983) but not a lot in the last 8 years. I didn't know if they added some kind of CDR controls in other LD's? I even reloaded the switch! I get CDR fine from RDB 49 but not RDB 9.

 

[informidicate]

Make sure that the programming on the COT trunks does not have SUPN YES, people mistakely think that on a COT trunk
that the SUPN (supervision) prompt is for disconnect
supervision when it is actually for answer supervision.
If you have SUPN YES then the pbx is waiting for the CO to
send back an acknowledgement that the call was answered.
Then the pbx will output a CDR record for that call when
it terminates. Hotels sometimes have their trunks provisioned that way so that their call accounting system
doesn't send a call record to the PMS system on a call
that was made but no one answered the call thus charging the guest for an incompleted call.

 

[carldest]

That was it. Thanks for the tip.