Can not dial out on PRI

[cpm23]

I have a new PRI that I can not dial out on. Below is what I get when I turn on Dchannel messaging (I Xed out the last four digits). The guy at the CO says I need to send E164, not E163. I have tried putting a DMI in the RLI to change the call type, but it stays the same no matter what I put at the CTYP prompt. Incoming works fine. It is working out of a 5ESS office and is programmed as custom.

DCH 6 OMSG SETUP REF 00000014 CH 1 20 TOD 19:12:24
CALLING #:561721XXXX NUM PLAN: E163/NATIONAL (UNKNOWN)
CALLED #:1305372XXXX NUM PLAN: E163/NATIONAL (UNKNOWN)

DCH 6 IMSG REL COMP REF 00000014 CH 1 20 TOD 19:12:24
CAUSE :INVALID IE CONTENTS

Your help would be appreciated.

 

[M1spezi]

Plese print the Net Data ,SPN´s, RLB and DGT

 

[cpm23]

In my RLB rote 7 is 1st choice, but it not connected yet so calls go out route 6.

ROUT 6

TYPE RDB
CUST 00
DMOD
ROUT 6
DES VERIZON
TKTP DID
M911_ANI NO
M911_TONE NO
NPID_TBL_NUM 0
SAT NO
RCLS EXT
VTRK NO
DTRK YES
BRIP NO
DGTP PRI
ISDN YES
MODE PRA
IFC ESS5
SBN NO
PNI 00002
SRVC NNSF
NCNA YES
NCRD NO
CHTY BCH
ISAR NO
CPUB OFF
DAPC NO
BCOT 0
DSEL VOD
PTYP PRI
AUTO NO
DNIS NO
DCDR NO
ICOG IAO
RANX NO
SRCH RRB
TRMB YES
STEP
ACOD 7006
TCPP NO
PII NO
TARG
CLEN 1
BILN NO
OABS
INST
IDC NO
DCNO 0 *
NDNO 0
DEXT NO
ICIS YES
TIMR ICF 512
OGF 512
EOD 13952
NRD 10112
DDL 70
ODT 4096
RGV 640
FLH 510
GRD 896
SFB 3
NBS 2048
NBL 4096


PAGE 002


IENB 5
VSS 0
VGD 6
DRNG NO
CDR NO
VRAT NO
MUS NO
EQAR NO
FRL 0 0
FRL 1 0
FRL 2 0
FRL 3 0
FRL 4 0
FRL 5 0
FRL 6 0
FRL 7 0
OHQ NO
OHQT 00
TTBL 0
ATAN NO
PLEV 2
MCTS NO
ALRM NO
ART 0
SGRP 0
AACR NO

>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>
MEM AVAIL: (U/P): 2917186 USED U P: 161005 67536 TOT: 3145727
DISK RECS AVAIL: 407
REQ prt
CUST 0
FEAT net
TRAN ac1
TYPE spn

SPN 1305 372

SPN 1305372
FLEN 11
ITOH NO
RLI 5
SDRR NONE
ITEI NONE
>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>

ENTR 1
LTER NO
ROUT 6
TOD 0 ON 1 ON 2 ON 3 ON
4 ON 5 ON 6 ON 7 ON
VNS NO
CNV NO
EXP NO
FRL 3
DMI 16
FCI 0
FSNI 0
SBOC NRR
IDBB DBA
IOHQ NO
OHQ NO
CBQ NO

ISET 0
NALT 5
MFRL 0
OVLL 0
>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>
MEM AVAIL: (U/P): 2917186 USED U P: 161005 67536 TOT: 3145727
DISK RECS AVAIL: 407
REQ prt
CUST 0
FEAT dgt
DMI 16


DMI 16
DEL 0
CTYP UKWN
>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>
CUST 0

TYPE NET_DATA
CUST 00
OPT RTA
AC1 INTL NPA SPN NXX LOC
AC2
FNP YES
ISDN YES
VPNI 0
PNI 2
PINX_DN
MBG 0
BSGC 65535
PFX1 561
PFX2 687
HLOC
LSC
RCNT 5
PSTN NO
TNDM 15
PCMC 15
SATD 1
OCLI NO
DITI NO
TRNX NO
EXTT NO
FTOP FTLY
VNR NO
NIT 8
NAS_ATCL YES
NAS_ACTV NO
FOPT 14
CNTC
NATC
INTC

Thanks

 

[M1spezi]

Hi, change calltyp in DGT 16 from UKWN to INTL.

 

[cpm23]

Unfortunately, no change.

 

[tnphoneman]

Post the Dchannel

Signature===========================================
Artificial Intelligence Is No Match for Natural Stupidity.

The latest survey shows that 3 out of 4 people make up 75% of the population.

The original point and click interface was a Smith & Wesson.

Red meat is not bad for you, it is the green fuzzy meat that is bad.

 

[cpm23]

Dchannel programming:

ADAN DCH 6
CTYP TMDI
CARD 01
PORT 1
DES Verizon
USR PRI
DCHL 1
OTBF 32
PARM RS232 DTE
DRAT 64KC
CLOK EXT
IFC ESS5
SIDE USR
CNEG 1
RLS ID 1
RCAP ND2
MBGA NO
OVLR NO
OVLS NO
T200 3
T203 10
N200 3
N201 260
K 7

Thanks for any help

 

[tnphoneman]

The number 1305 is not international you need the DMI to change the call type to NPA. Why is this built as an SPN? This should be built as a NPA and if you need to break out nxx areas within the area code you can use fcas tables.


Signature===========================================
Artificial Intelligence Is No Match for Natural Stupidity.

The latest survey shows that 3 out of 4 people make up 75% of the population.

The original point and click interface was a Smith & Wesson.

Red meat is not bad for you, it is the green fuzzy meat that is bad.

 

[cpm23]

Thanks, but NPAs don't work either. Same incoming message from the CO. I changed the DMI to INTL in response to an earlier reply from M1spezi in this forum. I've tried NXX as well. I have also tried it without a DMI table. You're right about the FCAS table, but the routing was built already.

 

[tnphoneman]

Print the FTR_DATA in ld 21.

Signature===========================================
Artificial Intelligence Is No Match for Natural Stupidity.

The latest survey shows that 3 out of 4 people make up 75% of the population.

The original point and click interface was a Smith & Wesson.

Red meat is not bad for you, it is the green fuzzy meat that is bad.

 

[cpm23]

This is the FTR_DATA. Thanks.

REQ: prt
TYPE: ftr
TYPE FTR_DATA
CUST 0

TYPE FTR_DATA
CUST 00
TBL
**DAPC**PREFIX TABLE NO: 00 **
UNKN**INTL**NATL**ESPN**LOCL**ELOC**ECDP**
UNKN*
E164* 00 0
PRIV*
E163* 00 0
TELX*
X121*
NATL*

OPT AHD BIND BIXA BLA CFF CFRA
COX CPA CTA DBD DNX DSX
HTU HVD XBL IC1 IDP XLF
IHA ITG FKA LOA LRA MCI
MWUD PVCD REA RNA
RTR RTA ROX SBD SYD
TTAD VOBA CWRD HLPD HRLD
CXOA
DGRP 30
IRNG NO
PKND 1
DNDL NO
SPRE 5199
PREO 0
BPSS NO
SRCD 6666
EEST NO
EESD NO
TTBL 0
MUS NO
ALDN
RECD NO
PORT 0
STCB NO
NSCP NO
MCDC NO
NAUT NO
IDEF NO
MTAR NO
LEND NO
MSCD NO
CPCI NO
CONF_DSP
CNFFIELD NO
CNF_NAME CONF
INTFIELD NO
INT_NAME I
EXTFIELD NO
EXT_NAME E
BSFE NO
ASPCT 010
FXS NO
DFLT_LANG ENG
STS_MSG
MSG01 Please leave message
MSG02 Back to work
MSG03 In a meeting
MSG04 On a conference call
MSG05 At lunch
MSG06 Busy call
MSG07 Out of the office today
MSG08 On a business trip
MSG09 Project deadline today
MSG10 Will reply after
VO_ALO NO
PCA ON
TPDN

 

[Labash]

Can you complete the call by accessing the trunk directly?.... dialing the access code before the number?

 

[cpm23]

No to both questions. I have tried using LD 36 thru the maintenance set and by using the ACOD. The provider is in the process of changing the protocol to DMS100. Hopefully that'll do it. Thanks for your response.

 

[yyrkroon]

set your dmi to delete 1 and insert nothing and ctype = npa. some telco don't want to see the 1 and some do...

 

[cpm23]

Thanks to everyone that replied. The provider had to change the Dchannel protocol to DMS100 to get it to work. I don't know why. I've been able to use ESS5 many times before.

 

[tnphoneman]

That would depend on what type of switch they had at the CO. If it is a DMS then DMS100 is the correct way. However now days NI2 is the preferred method no matter what type of CO is involved.

Signature===========================================
Artificial Intelligence Is No Match for Natural Stupidity.

The latest survey shows that 3 out of 4 people make up 75% of the population.

The original point and click interface was a Smith & Wesson.

Red meat is not bad for you, it is the green fuzzy meat that is bad.