Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations strongm on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Caller ID

Status
Not open for further replies.
DWShetler

DWShetler

MIS
Feb 4, 2002
82
US
I've had some issues with my phone system. In fact some of the modular units have been replaced. Everything is up and running for about 3 weeks no with no problems.

There is one issue I was hoping someone knew how to fix. Before our problems, when outsiders called our DID's, caller ID would pop up before we answered the phone. Now, it says Line xxx to Prime and then caller ID will usually (99% of the time) pop up AFTER you have answered the call. Anyone know the programming to switch it back to the way it was????

 
Sort by date Sort by votes
I am assuming you are working with PRI. Regardless, are your DID's assigned to ring and appear on the sets? Also, check that Caller ID is enabled for that set/DID.
 
Upvote 0 Downvote
What is the line number that it shows going to prime?
 
Upvote 0 Downvote
thats just it, I don't know how to check if caller id is set on each set and I believe I am set up to have DID ring on each set.

the line number that appears is what ever line number is suppose to ring on that phone. IE mine says Line 196 to Prime and my neighbors says Line 150 to Prime
 
Upvote 0 Downvote
Terminals&Sets - Show
Show set: ___ - Enter your extension number.
223:223 - SHow
Line Access - Show
Line Assignment - Show
Show line: ___ - Enter line 196.
L196:unassigned - Press change until it says Ring Only.
Then press your header button until you see
Line Access - Next until you see
Telco Features - Show
Feature assign - SHow
Show line: ___ - Enter 196
L196: 196 - Press Show
Caller ID set: N. - Change to yes.

Do the same for the other ext with the other line number.


MRoberts
 
Upvote 0 Downvote
You might also want to check the Lines->196->Trunk/line data->CLID set:___

JerryReeve
Communications Systems Int'l
com-sys.com
 
Upvote 0 Downvote
that did...thanks guys...one other question when a user has a vm it used to flash a little red light on his phone, now it doesn't. I went in and set it so that the indication was "lamp" but that didnt fix...any other ideas on this one??
 
Upvote 0 Downvote
although when I go into the system on his extension it is telling me its an M7208 with no option to change it
 
Upvote 0 Downvote
you stated your recently changed out some modular units...what did you change to? Did you (or a vendor) change software?
 
Upvote 0 Downvote
a vendor changed it, I would never attempt it. They know more than me and thats why I pay them to come in.

I am higher than 4.1.1 but still using 4.x.x

Yes it does say msg for you, its just he's crying because he wants his red light to blink also
 
Upvote 0 Downvote
Status
Not open for further replies.

Similar threads

Michael OConnor
  • Locked
  • Question
Caller ID Outputting weird characters
Replies
2
Views
99
Michael OConnor
Michael OConnor
accumatt
  • Locked
  • Question
Caller ID Not Working On Outbound Transfer Via Call Pilot 150
Replies
1
Views
125
accumatt
accumatt
Atechguyy
  • Locked
  • Question
NT8B88FA call ID C6 work On Norstar 3x8 dr.5 /5.1????????
Replies
6
Views
161
Atechguyy
Atechguyy
NonTechFolks
  • Locked
  • Question
Caller ID on T7316E
Replies
3
Views
124
curlycord
curlycord
Mark.Brown
  • Locked
  • Question
Have a Norstar NT5B01 and Norstar phones, want caller ID
Replies
2
Views
87
noreth
noreth

Part and Inventory Search

Sponsor

Back
Top