Call forwarding a DN to a cell phone on a 11C 1

[richi23]

Hi all,

I have a meridian 11C and i'm trying to forward my DN 3311 to my cell phone. When i call from another DN it says "Release and try again" and from an outside line it goes directly to the reception.

I changed CLS to CFXA, CFHA and SFA
and OPT on RDR_DATA and FTR_DATA to CFF
and Net Data - TRNX-YES
EXTT-YES

My TN is as follows:

REQ: prt
TYPE: 2616


TN 3 2
DATE
PAGE
DES

DES 3311
TN 003 0 00 02
TYPE 2616
CDEN 8D
CUST 0
AOM 0
FDN 7000
TGAR 1
LDN NO
NCOS 0
SGRP 0
RNPG 0
SCI 0
SSU 0000
LNRS 16
XLST
CLS CTD FBA WTA LPR MTD FNA HTA TDD HFA
MWA LMPN RMMD SMWD AAD IMD XHD IRD NID OLD VCE DRG1
POD DSX VMD CMSD SLKD CCSD SWD LNA CNDA
CFTD SFA MRD DDV CNID CDCA MSID DAPA BFED RCBD
ICDA CDMD LLCN MCTD CLBD AUTU
GPUD DPUD DNDA CFXA ARHD CLTD ASCD
CPFA CPTA ABDD CFHA FICD NAID BUZZ AGRD MOAD
AHA DDGA NAMA
DRDD EXR0
USRD ULAD RTDD RBDD RBHD PGND OCBD FLXD FTTC DNDY DNO3 MCBN
CPND_LANG ROM
RCO 0
HUNT 7000
LHK 1
PLEV 02
AST
IAPG 0
AACS NO
ITNA NO
DGRP
MLWU_LANG 0
DNDR 0
KEY 00 MCR 3311 1 MARP
CPND
NAME My Name
XPLN 24
DISPLAY_FMT FIRST,LAST
01 MCR 3311 1
CPND
NAME My Name
XPLN 24
DISPLAY_FMT FIRST,LAST
02 ADL 16
03 TRN
04 AO6
05 CFW 12 91514xxxxxxx
06 ADL 16 0
07
08 MWK 7000
09 ADL 16
10 ADL 16
11 ADL 16
12 ADL 16
13 ADL 16 0
14 ADL 16
15
DATE 20 MAR 2008

Please help me figure out what's wrong

Thanks

 

[phonz1]

up your NCOS

 

[richi23]

How do i list all the NCOS on the phone system?

 

[MikeRizz]

LD 86
PRT
Type : ESN

 

[richi23]

I changed my NCOS to 9 but still the same problem

 

[bigindian65]

that will show you the same list everyone else has, to see which is in use there is a place to prt NCOS, I can't remember where - ACE knows.

to see what is on phonesets - ld 81 lst
feat: ncos 1

the do 2,3,4,5 etc...

Mato' Was'aka

 

[pbxn]

to print your ncos
ld 87
prt
0
nctl
cr
cr
cr

 

[richi23]

The majority of our phones are on NCOS 0 because setup to be used with a code to dial out.

only some are on NCOS 4

and modems are on NCOS 6

Is the only way to make the call forward work to change the NCOS?

 

[pronei]

No, you're forwarding long distance which is 11 digits. I am assuming you have a 4 digit ACOD on your trunks, therefore you need at least a total of 15 digits in the CFW key on your phone, up the 12 to 16 and you should be fine.

 

[cscsupport]

The only other thing you could check if that doesnt work is the tgar on your set.

 

[pronei]

TGAR is only a problem if you can't make long distance calls at all.

 

[acewarlock]

Make the phone a NCOS 4 if other phones that have an NCOS 4 can dial that number then you have everything else right.

You only Need the NCOS that can dial LD, CLS CFXA and the CDB (CFF) you didn't need to change the others.


This is something else I saw wrong.
Also on your CLS you have FBA (Forward on BUSY TO ATT), you should only have FBA if you want your calls to go to the ATT if you are on the phone.




This is a Signature and not part of the answer, it appears on every reply.

This is an Analogy so don't take it personally as some have.

Why change the engine if all you need is to change the spark plugs.

 

[johnpoole]

re-read ace's post.. the most common block is cfo in the cdb. that looks at the ncos of the inbound trunk for cfxa..


the ncos of the phone has to be high enough to make the call, no higher... if ncos 9 is not defined then it;s default is the same as ncos 0...

if you can call your cell from the phone and the phone has cfxa... leave the phone alone...

is you cdb opt cff? let us know about those two and we can check one other thing,,

that targ on the routes can not match... if your using the same route inbound and outbound... post that rdb

john poole
bellsouth business
columbia,sc

 

[mcgee99]

As someone else said; FBA (CLS) must be chg'd to FBD. Also, is 1514 listed as a valid NPA in LD 90? Should be programmed as an NPA, but can also be programmed as an SPN. Do a PRT on both NPA and SPN, if you do not find it in either of those, add it to your NPA's, then test dial.

 

[johnpoole]

is 1514 listed as a valid NPA in LD 90

tried to cover that with "can you dial the number from the phone?"

that alone takes ncos and npa/nxx out of the picture... six responses since rich answered a question... i usually stay with a problem untill it's working

john poole
bellsouth business
columbia,sc

 

[NastyNed2]

I'm reading this with interest as I have someone who will be recovering at home from radiation treatments and we'll need to forward his office phone to his cell phone.

One thing I noticed in the CLS on the posted TN is CTD, conditionally toll denied. I forget what these 6 settings all do without reading the book (FR1, FR2, CTD, UNR, etc.). Try changing CTD to UNR (unrestricted) and let us know how it works. I was unsuccessful in a previous attempt to allow CFXA to a cell phone.

 

[a12ozbottle]

Print NCTL in ld 87 this will give you the FRL of a given NCOS, then you need to look at the RLI in ld 86 and see what FRL is set at.

 

[richi23]

Sorry guys i was sick for 3 days and couldn't answer the posts.

Yes John the phone can dial the cell number and also LD but with a code.
I've also changed CLS to FBD and UNR

But still the same issue. Calls from outside to my number go to security instead of the cell number.

Thanks

 

[richi23]

DES 3311
TN 003 0 00 02
TYPE 2616
CDEN 8D
CUST 0
AOM 0
FDN 7000
TGAR 1
LDN NO
NCOS 9
SGRP 0
RNPG 0
SCI 0
SSU 0000
LNRS 16
XLST
CLS UNR FBD WTA LPR MTD FNA HTA TDD HFA
MWA LMPN RMMD SMWD AAD IMD XHD IRD NID OLD VCE DRG1
POD DSX VMD CMSD SLKD CCSD SWD LNA CNDA
CFTD SFA MRD DDV CNID CDCA MSID DAPA BFED RCBD
ICDA CDMD LLCN MCTD CLBD AUTU
GPUD DPUD DNDA CFXA ARHD CLTD ASCD
CPFA CPTA ABDD CFHA FICD NAID BUZZ AGRD MOAD
AHA DDGA NAMA
DRDD EXR0
USRD ULAD RTDD RBDD RBHD PGND OCBD FLXD FTTC DNDY DNO3 MCBN
CPND_LANG ROM
RCO 0
HUNT 7000
LHK 1
PLEV 02
AST
IAPG 0
AACS NO
ITNA NO
DGRP
MLWU_LANG 0
DNDR 0
KEY 00 MCR 3311 1 MARP
CPND
NAME My Name
XPLN 24
DISPLAY_FMT FIRST,LAST
01 MCR 3311 1
CPND
NAME My Name
XPLN 24
DISPLAY_FMT FIRST,LAST
02 ADL 16
03 TRN
04 AO6
05 CFW 16 9514xxxxxxx
06 ADL 16 0
07
08 MWK 7000
09 ADL 16
10 ADL 16
11 ADL 16
12 ADL 16
13 ADL 16 0
14 ADL 16
15
DATE 27 MAR 2008

And i've changed cdb opt to cff

Thanks

 

[acewarlock]

Were banging our heads againest the wall here. Just raising the NCOS to a 9 doesn't mean the phone will work, because NCOS 9 may be a FRL 0 and that won't let the call go though.

Goto LD 81 and do
REQ CNT
CUST 0
enter until FEAT
FEAT NCOS
Then ENTER Until it prints and then POST HERE






This is a Signature and not part of the answer, it appears on every reply.

This is an Analogy so don't take it personally as some have.

Why change the engine if all you need is to change the spark plugs.