hassancheg
IS-IT--Management
Hello,
I'm tryng to setup Avaya SBS trunk, to send signaling information (Caller ID and name) in calls through limited PSTN.
I created 2 SBS H.323 trunks on both sides (CM6 PBXs), SBS extension on receiving side, filled public-unknown-numbering table and assigned DID number on receiving PBX to station.
According to Job Aid document, SBS contains next steps:
1) station on PBX A calls SBS extension on PBX B, through SBS H.323 trunk
2) On PBX B, special SBS extension receives call with signaling portion (Caller ID, caller name) and send to PBX A phone number for voice bearer call (from public-unknown table)
3) staion on PBX A receives number for voice bearer, and call this number (via PSTN)
4) call arrives to PBX B via PSTN, and PBX B send call ID via SBS trunk to PBX A
5) PBX A send call ID in bearer call, using DTMF. SO, bearer call and signaling portion can be assigned in same call.
But, when I trying to make SBS call, everything goes fine, except call ID sending on PBX B (terminating node).
Where is point in setup, that i missed?
Here is trace on terminating node (SBS trunk):
on originating node (trace from station)
I'm tryng to setup Avaya SBS trunk, to send signaling information (Caller ID and name) in calls through limited PSTN.
I created 2 SBS H.323 trunks on both sides (CM6 PBXs), SBS extension on receiving side, filled public-unknown-numbering table and assigned DID number on receiving PBX to station.
According to Job Aid document, SBS contains next steps:
1) station on PBX A calls SBS extension on PBX B, through SBS H.323 trunk
2) On PBX B, special SBS extension receives call with signaling portion (Caller ID, caller name) and send to PBX A phone number for voice bearer call (from public-unknown table)
3) staion on PBX A receives number for voice bearer, and call this number (via PSTN)
4) call arrives to PBX B via PSTN, and PBX B send call ID via SBS trunk to PBX A
5) PBX A send call ID in bearer call, using DTMF. SO, bearer call and signaling portion can be assigned in same call.
But, when I trying to make SBS call, everything goes fine, except call ID sending on PBX B (terminating node).
Where is point in setup, that i missed?
Here is trace on terminating node (SBS trunk):
Code:
LIST TRACE
time data
16:24:20 TRACE STARTED 09/26/2017 CM Release String cold-00.1.510.1-21061
16:24:25 Calling party trunk-group 7 member 1 cid 0x3c27
16:24:25 Calling Number & Name 3307 Yaroslav
16:24:25 active trunk-group 7 member 1 cid 0x3c27
16:24:25 dial 5555
16:24:25 term station 5555 cid 0x3c27
on originating node (trace from station)
Code:
LIST TRACE
time data
16:23:59 TRACE STARTED 09/26/2017 CM Release String cold-03.0.124.0-23382
16:24:24 active station 3307 cid 0x2191
16:24:24 G711A ss:off ps:20
rgn:1 [106.125.2.81]:2176
rgn:1 [106.125.22.11]:2080
16:24:28 dial 5555# route:UDP|AAR
16:24:28 term trunk-group 11 cid 0x2191
16:24:28 dial 5555# route:UDP|AAR
16:24:28 route-pattern 99 preference 1 location 1/ALL cid 0x2191
16:24:28 seize trunk-group 11 member 6 cid 0x2191
16:24:28 Setup digits 5555
16:24:28 Calling Number & Name 3307 Yaroslav Pork
16:24:28 Proceed trunk-group 11 member 6 cid 0x2191
16:24:28 active service-link cid 0x2192
16:24:28 dial ################ route:ARS
16:24:28 term trunk-group 1 cid 0x2192
16:24:28 dial ################ route:ARS
16:24:28 route-pattern 3 preference 1 location 1/ALL cid 0x2192
16:24:28 seize trunk-group 1 member 17 cid 0x2192
16:24:28 Setup digits ################
16:24:28 Calling Number & Name %%%%%%%%% NO-CPName
16:24:28 Proceed trunk-group 1 member 17 cid 0x2192
16:24:31 Alert trunk-group 1 member 17 cid 0x2192
16:24:38 active trunk-group 1 member 17 cid 0x2192
16:25:26 idle trunk-group 1 member 17 cid 0x2192