ALI-IV-PCI

[Vilse]

Hello!

Where can i find inforamtion about ALI-IV-PCI? this card is used in Nice Digital Logger.
In the back side of this card there is three diodes (ACT, DSP and TERM) and i want to know what these diodes means.

I have tried to search the web but can´t find anything.
Please help=)

/DN

 

[nice12345]

https://www.extranice.com/EIS/Pages/searchresults.aspx?k=ali IV&s=All Sites

 

[Vilse]

Thanks for reply but i have been in there an looked at "Nice Hardware Diagnostic Tools Webinar Presenation" but i can not find anything about the card and the diodes.

 

[nice12345]

act -activity
dsp - 1 dsp per 8 channel
term - termination depends whether if card is terminated or not as per high density logger hardware manual

 

[nice12345]

all the info on leds etc and board can be found on this pdf

https://www.extranice.com/EIS/Addit...CI Interface Board (NCBD-0043-50 Rev. A5).pdf

 

[nice12345]

LED Description
Board Active Lights up when board is active
DSP Lights up when DSP has no error
Termination Lights up when termination is activated in the board

 

[Vilse]

Thanks but when i try to follow the link you gave me and logon to extranice i got this error message: "The website declined to show this webpage" =(
I can logon to Extranice if i don´t follow you link, why?

What key word did you use to find the document?

 

[nice12345]

sorry cannot help you there. i searched on ali iv in extranice and found this document easily

 

[Vilse]

Ok, i have tried on two differnt comupters but i got the same eror message when i try to logon=(.

I have three Ali-iv-pci total of 72 channels.

The first board that hanldes channels 1-24 the status is like this: ACT is flashing, DSP and TERM is constant green.

The second board that handles channels 25-48: ACT is flashing, DSP ic constant green and TERM is don´t light up at all.

The third board that handles channels 49-72: none of the three status diodes light up at all.

I have activity on channels 1 and 25.

Is it something wrong with board 2 and three? do you know how i can activate the Termination?

 

[nice12345]

ok how many channel licenses do you have. do you see channel status in monitor/channel monitor if perform?

if its 8.9 have you enabled the channels?

 

[nice12345]

are the cards also connected via h100 or mvip cable if old version of NICE

 

[Vilse]

It is a ALI24 cable, this cable is used for an older verson of NiceLog that use ADIF24 card.
I have both an older version and a "newer" version of nicelog, the older version use ADIF24 card as above and the "newer" version use ALI 4 card.

Maybe i can´t connect ALI24 cable to ALI 4 card?
But i can see there is activity on channel 1 (channel one is board 1) and channel 25 (channel 25 is on board 2) on Nice Application 8.9 that i have installed in my workstation, but the boards diods act different?

I checked the config files i used when i installed "Nice perform Voice Logger SP3", then i saw that i used fonfig files for 48 channels.
I tried to reinstall everything but with config files for 72 channels. Now i can see that the third board is active also.

But i still can see that board one have the "Term" diod lighted upp but the "Term" diode on the other two boards don´t lights up at all.

Can i light up the termination somehow or should it be not lighted?

I use Nice application 8.9 with sp4 on my workstataion.