Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations Mike Lewis on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Added new analog set - can't dial out?

Status
Not open for further replies.
bad69cat

bad69cat

IS-IT--Management
May 28, 2010
280
US
SO I added another analog set to my remote OPT 11, by copying another set from the port next to the one I wanted. It looked like everything went OK and it built the set. When I went down and patched the set over I can't dial out? I get a fast busy as soon as I dial the last digit? Same as I do on any unused ports...? I looked at the programming on the set I copied from (which is working) and compared it to the new one. Looks identical except DN. I double checked that I am on the right TN and I am? I did a status on the port and it is idle. I haven't had to build and analog port in awhile, but I don't know hat I am missing? Ideas? Gotta be simple...?
 
Sort by date Sort by votes
First of all, is your system licensed to allow another 500 type phone?. I'm guessing it is as you wouldn't normally be allowed to program it in without an error code. What TN did you use?. Have to checked that it's wired from the TN port correctly?.

Failing that, you could just have a faulty port and I would swap out the card with another FALC one to check.

Firebird Scrambler

Nortel & Avaya Meridian 1 / Succession & BCM / Norstar Programmer

Website = linkedin
 
Upvote 0 Downvote
Hmmm it looks like I have 4 analog phones left that I can ad.... so I don't think I'm out of license's. I used TN 8 5 and the set on 8 4 is working. Ill try and bump it down to a different port. It doesn't make any sense that I can't dial the 4th digit though? even if it's a bad port it should try to dial? It seems like there is a software type issue somehow....? I am using an existing DN because I am converting a digital set to analog so they can have a cordless phone..... seemed like a no brainer. Ill drag my laptop and tools all down with me this time.... pain!
 
Upvote 0 Downvote
buddy - yes. No problems. That's what baffles me? I wonder if I reset that line card...? wonder if somehow it's hosed up? Ill bet it hasn't had a phone changed or added in 15 years....
 
Upvote 0 Downvote
That TN should be on the red/blue pair, starts at 0, remember?
 
Upvote 0 Downvote
yep. I went down today and got it going on a different card. There is something wrong with that line card. Only the first 5 ports seem to be working? Weird huh? I'll have to take another card down there the next time I go and swap it. See if that fixes it. I've never run into that issue before..... luckily it had 2 analog cards in it!
 
Upvote 0 Downvote
do the opt 11 and opt 81 share the same line cards?
 
Upvote 0 Downvote
Status
Not open for further replies.

Similar threads

Mokpokpo Agbovon
  • Locked
  • Question
Analog Phone Programming
Replies
4
Views
245
Firebird Scrambler
Firebird Scrambler
lastation4
  • Locked
  • Question
Digital Set will not ring IP set 2
Replies
14
Views
350
bignose21
bignose21
lastation4
  • Locked
  • Question
Can't get T1 DCH to establish
Replies
6
Views
235
lastation4
lastation4
bltodd
  • Locked
  • Question
ERR008 Digital and Analog Calls in Hang up after initial connection. Calls to outside hangup Fax too
Replies
0
Views
113
bltodd
bltodd
Rosesam
  • Locked
  • Question
CS1000 Wireless set options
Replies
4
Views
172
Firebird Scrambler
Firebird Scrambler

Part and Inventory Search

Sponsor

Back
Top