Add Local Toll prefixes and new area code. 1

[Brutus82]

I’m a converted NEC 2000IPS on-site tech that’s now working on a Nortel 61C so go easy! hehe

My problem is we have to add new Local Toll prefixes 207, 380, 466, 521, 567, 650, 788 to area code “234” and also add a completely new area code “567”.

When I first started here I called Verizon to add local prefixes 521, and 650 to area code “234”. It took the tech a long time to figure out how to do this because he said we had everything setup in “fcas” feature instead of the typical way that it’s done.

For instance when I try to look at our main local area code of “330” in LD 90 I get the following:

REQ prt
CUST 0
FEAT net
TRAN ac1
TYPE 1330

ESN061
TYPE



Here’s what we currently have in LD 87

prt
CUST 0
FEAT fcas
FCI 1
NPA 330

ALOW 209 214 218 224 232 236 244 265 266
268 280 284 290 292 293 305 309 312 313 316 320 323 324 327 353 359 361 363 371 408 409 412 413 415 417 418 430 433 437 438 445 450 451 452 453 454 455 456 458 470 471 477 478 479 481 484 488 489 490 491 492 493 494 495 497 498 499 508 514 516 526 546 566 575 579 580 588 605 639 649 685 704 705 709 737 754 756 767 768 775 791 806 809 818 826 828 830 832 833 834 837 838 844 854 879 880 891 902 904 915 918 919 933 936 949 955 956 966 970 985

NPA 234
ALOW 521 650


REQ prt
CUST 0
FEAT fcas
FCI 2
NPA 330

DENY 209 214 218 224 232 236 244 265 266 268 280 284 290 292 293 305 309 312 313 316 320 323 324 327 353 359 361 363 371 408 409 412 413 415 417 418 430 433 437 438 445 450 451 452 453 454 455 456 458 470 471 477 478 479 481 484 488 489 490 491 492 493 494 495 497 498 499 508 514 516 526 546 566 575 579 580 588 605 639 649 685 704 705 709 737 754 756 767 768 775 791 806 809 818 826 828 830 832 833 834 837 838 844 854 879 880 891 902 904 915 918 919 933 936 949 955 956 966 970 985

Any help in getting these additional changes done is GREATLY appreciated.

Thank You!

 

[johnpoole]

prt
0
net
ac1
npa
1330

type is npa not 1330.. try that and post back.. i would out the fcas unless your paying extra for some nxx's.. other choice is adding the new number to the allow table..

for the new npa. ld 90.. prt (from above) any clean npa, not the rli..l then same commands starting with new, add the rlb and that one is done

john poole
bellsouth business
columbia,sc

 

[johnpoole]

if you can do the nec, this one is a dream.. i do both and perfer the routing on this one..

john poole
bellsouth business
columbia,sc

 

[Brutus82]

Thanks johnpoole this is what I get:

CUST 0
FEAT net
TRAN ac1
TYPE npa

NPA 1330

NPA 1330
RLI 20
DENY 5551212

DENY 976

SDRR DENY CODES = 2
ITEI NONE




REQ prt
CUST 0
FEAT net
TRAN ac1
TYPE npa

NPA 1567

ESN071

NPA 330

NPA 330
RLI 6
DENY 976

SDRR DENY CODES = 1
ITEI NONE




REQ prt
CUST 0
FEAT net
TRAN ac1
TYPE npa

NPA 1234

NPA 1234
RLI 20
DENY 5551212

DENY 976

SDRR DENY CODES = 2
ITEI NONE




REQ prt
CUST 0
FEAT net
TRAN ac1
TYPE npa

NPA 234

NPA 234
RLI 20
DENY 976

SDRR DENY CODES = 1
ITEI NONE

 

[Brutus82]

Ok I was able to add the new LD area code "567" and it works perfect however, I'm still confused with the way "fcas" works.

We basically have two area codes that are both local and local toll, 330 and now 234. In fci 1 for area code 330 (Main) they allow all local prefixes. In fci 2 area for code 330 (Main) they deny all local prefixes. When you place a call our switch correctly knows when you need to add a 1 before the phone number.

I tried to do the same with area code 234, allowing local prefixes in fci 1 and denying local toll prefixes in fci 2. What happens is you can't dial any local prefixes and the local toll prefixes go through without asking for the 1.

Here's what I have:

LD 87

FCI 1

NPA 330
ALOW 209 214 218 224 232 236 244 265 266 268
280 284 290 292 293 305 309 312 313 316
320 323 324 327 353 359 361 363 371 408
409 412 413 415 417 418 430 433 437 438
445 450 451 452 453 454 455 456 458 470
471 477 478 479 481 484 488 489 490 491
492 493 494 495 497 498 499 508 514 516
526 546 566 575 579 580 588 605 639 649
685 704 705 709 737 754 756 767 768 775
791 806 809 818 826 828 830 832 833 834
837 838 844 854 879 880 891 902 904 915
918 919 933 936 949 955 956 966 970 985


NPA 234
ALOW 521 650


FCI 2

NPA 330
DENY 209 214 218 224 232 236 244 265 266 268
280 284 290 292 293 305 309 312 313 316
320 323 324 327 353 359 361 363 371 408
409 412 413 415 417 418 430 433 437 438
445 450 451 452 453 454 455 456 458 470
471 477 478 479 481 484 488 489 490 491
492 493 494 495 497 498 499 508 514 516
526 546 566 575 579 580 588 605 639 649
685 704 705 709 737 754 756 767 768 775
791 806 809 818 826 828 830 832 833 834
837 838 844 854 879 880 891 902 904 915
918 919 933 936 949 955 956 966 970 985


NPA 234
DENY 521 650




LD 90

FEAT net
TRAN ac1
TYPE npa

NPA 1330

NPA 1330
RLI 20
DENY 5551212

DENY 976

SDRR DENY CODES = 2
ITEI NONE




FEAT net
TRAN ac1
TYPE npa

NPA 330

NPA 330
RLI 6
DENY 976

SDRR DENY CODES = 1
ITEI NONE




FEAT net
TRAN ac1
TYPE npa

NPA 1234

NPA 1234
RLI 20
DENY 5551212

DENY 976

SDRR DENY CODES = 2
ITEI NONE




FEAT net
TRAN ac1
TYPE npa

NPA 234

NPA 234
RLI 20
DENY 976

SDRR DENY CODES = 1
ITEI NONE

 

[Reusser]

looks like you need to have 234 go to RLI 6 like 330 does


NPA 234
RLI 20 <-- change to RLI 6
DENY 976

NPA 330
RLI 6
DENY 976

The one piece of the puzzle you are missing is the RLI
LD 86
Req: prt
Cust:
Feat: RLB
RLI: <-- enter 6 and then print again and enter 20. RLI will have multiple entries with FCI assignments. There will also be DMI assignment which will insert or delete digits.