Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations Chriss Miller on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

2650 load balancing DSL's CHAP pppoa 2

Status
Not open for further replies.
tksavoy

tksavoy

IS-IT--Management
Joined
May 1, 2008
Messages
22
Location
US
What's wrong with my config?

DSLrouter#sh run
Building configuration...

Current configuration : 2473 bytes
!
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname DSLrouter
!
boot-start-marker
boot-end-marker
!
enable secret 5 xxxxxxxxxxxxxxxxxxxxxxxxx
!
no aaa new-model
no network-clock-participate slot 1
no network-clock-participate wic 0
ip cef
!
!
!
!
!
!
!
!
!
!
!
interface ATM0/0
no ip address
no atm ilmi-keepalive
dsl operating-mode auto
hold-queue 224 in
pvc 0/35
!
interface FastEthernet0/0
ip address 192.168.xx7.5 255.255.255.0
no ip redirects
no ip proxy-arp
ip nat inside
speed 100
full-duplex
!
interface ATM0/1
no ip address
no atm ilmi-keepalive
dsl operating-mode auto
pvc 0/35
!
interface Dialer0
ip address 207.xxx.xx.xx0 255.255.255.0
ip mtu 1492
ip nat outside
encapsulation ppp
dialer pool 1
ppp authentication chap callin
ppp chap hostname xxxxxxxx
ppp chap password 0 xxxxxxxx
!
interface Dialer1
ip address 207.xxx.xx.xx1 255.255.255.0
ip mtu 1492
ip nat outside
encapsulation ppp
dialer pool 1
ppp authentication chap callin
ppp chap hostname xxxxx
ppp chap password 0 xxxxx
!
interface Dialer2
ip address negotiated
ip mtu 1492
ip nat outside
encapsulation ppp
dialer pool 1
ppp authentication chap callin
ppp chap hostname xxxxx
ppp chap password 0 xxxxx
!
ip default-gateway 192.168.107.3
ip forward-protocol nd
ip route 0.0.0.0 0.0.0.0 Dialer1
ip route 0.0.0.0 0.0.0.0 Dialer2
ip route 0.0.0.0 0.0.0.0 Dialer0
ip route 192.168.xx8.0 255.255.255.0 192.168.xxx.3
ip route 192.168.xx9.0 255.255.255.0 192.168.xxx.3
ip route 192.168.x10.0 255.255.255.0 192.168.xxx.3
ip route 192.168.x11.0 255.255.255.0 192.168.xxx.3
ip route 192.168.x12.0 255.255.255.0 192.168.xxx.3
ip route 192.168.x13.0 255.255.255.0 192.168.xxx.3
!
ip http server
no ip http secure-server
ip nat pool dsl0 207.xxx.xx.xx0 207.xxx.xx.xx0 netmask 255.255.255.0
ip nat pool dsl1 207.xxx.xx.xx1 207.xxx.xx.xx1 netmask 255.255.255.0
ip nat inside source route-map dsl0 pool dsl0 overload
ip nat inside source route-map dsl1 pool dsl1 overload
!
access-list 1 permit 192.168.xxx.0 0.0.0.255
route-map dsl1 permit 10
match ip address 1
match interface dialer0
!
route-map dsl0 permit 10
match ip address 1
match interface dialer1
!
!
control-plane
!
!
line con 0
line aux 0
line vty 0 4
password xxxxxx
login
!
!
end
 
Sort by date Sort by votes
No output to the internet. the interfaces are up, up. but can't get out to the internet. It has 2 wic adsl's. Thanks Tommy
 
Upvote 0 Downvote
no ip nat pool dsl0 207.xxx.xx.xx0 207.xxx.xx.xx0 netmask 255.255.255.0
no ip nat pool dsl1 207.xxx.xx.xx1 207.xxx.xx.xx1 netmask 255.255.255.0
no ip nat inside source route-map dsl0 pool dsl0 overload
no ip nat inside source route-map dsl1 pool dsl1 overload
no route-map dsl1 permit 10
no route-map dsl0 permit 10
int di0
ip tcp adjust-mss 1452
dialer-list 1
no ppp authentication chap callin
ppp authentication pap chap callin
ppp chap hostname xxxxx
ppp chap password xxxxx
ppp pap sent-username xxxx password xxxx

int di1
ip tcp adjust-mss 1452
dialer-list 1
no ppp authentication chap callin
ppp authentication pap chap callin
ppp chap hostname xxxxx
ppp chap password xxxxx
ppp pap sent-username xxxx password xxxx
ip nat inside source list 1 int di0 overload
ip nat inside source list 1 int di1 overload
int atm0/0.1 point-to-point
pvc 0/35
oam-pvc manage
pppoe-client dial-pool-number 1
int atm 0/1.1 point-to-point
pvc 0/35
oam-pvc manage
pppoe-client dial-pool-number 1
int atm0/0
no pvc 0/35
int atm0/1
no pvc 0/35

Burt
 
Upvote 0 Downvote
Thanks Burt for the post, I noticed you put a ppp pap statement and I am using chap.

Also you used pppoe and my isp uses pppoa.

I am a cisco switch guy, so I appreciate your post and patience. Thanks Tommy
 
Upvote 0 Downvote
My ISP told me that I was using CHAP as well, but it didn't work. Sorry---didn't notice the PPPoA...but I would imagine the main problem was the NAT config.

Burt
 
Upvote 0 Downvote
it won't let me type dialer-list 1
it chokes on the list part
when I do a help it tells me that the only dialer option is dialer-group. Thanks Tommy
 
Upvote 0 Downvote
Pos a sh ver, and we should get a good config worked out. What model router is this anyway?

Burt
 
Upvote 0 Downvote
Router is a 2650. I will post a sh ver. Thanks
 
Upvote 0 Downvote
here is the sh ver

Cisco IOS Software, C2600 Software (C2600-IPBASEK9-M), Version 12.4(19), RELEASE
SOFTWARE (fc1)
Technical Support: Copyright (c) 1986-2008 by Cisco Systems, Inc.
Compiled Fri 29-Feb-08 19:23 by prod_rel_team

ROM: System Bootstrap, Version 12.2(7r) [cmong 7r], RELEASE SOFTWARE (fc1)

DSLrouter uptime is 1 day, 19 hours, 18 minutes
System returned to ROM by power-on
System image file is "flash:c2600-ipbasek9-mz.124-19.bin"


This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.

A summary of U.S. laws governing Cisco cryptographic products may be found at:

If you require further assistance please contact us by sending email to
export@cisco.com.

Cisco 2650XM (MPC860P) processor (revision 1.0) with 62091K/3445K bytes of memor
y.
Processor board ID JAD07100KLG
M860 processor: part number 5, mask 2
1 FastEthernet interface
2 ATM interfaces
32K bytes of NVRAM.
16384K bytes of processor board System flash (Read/Write)

Configuration register is 0x2102
end
 
Upvote 0 Downvote
Looks like you may need to update the IOS. I have one that works, but you'll need another 64MB DRAM...

Burt
 
Upvote 0 Downvote
what version do i need? and what router is yours on? and what is the total dram needed. Thanks Tommy
 
Upvote 0 Downvote
mINE IS A 2620xm, AND i HAVE ADVANCED ENTERPRISE 12.4(10)
You need 128MB of DRAM and I believe more than 32MB of flash (like a 32MB module, giving you 48 with the 16 onboard flash). I tried advanced security IOS and advanced enterprise 12.4(9), but neither worked with my WIC-1ADSL...perhaps someone else can shed some light? If you upgrade the DRAM and flash, I'd be happy to share the IOS...

Burt
 
Upvote 0 Downvote
This is my atm status

DSLrouter#sh atm pvc ppp
VCD / VA Peak Avg/Min Burst VC
ATM Int. Name VPI VCI Type VA St SC Kbps Kbps Cells St
0/0.1 4 0 35 PVC 2 DN UBR 256 UP
0/1.1 4 0 35 PVC 3 DN UBR 640 UP
 
Upvote 0 Downvote
mine is a 2650xm. The virtual-access2 and 3 or down all other interfaces are up. Thanks Tommy
 
Upvote 0 Downvote
Here is the new config

Building configuration...

Current configuration : 2154 bytes
!
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname DSLrouter
!
boot-start-marker
boot-end-marker
!
enable secret 5 $1$u1GD$Vvb7Nx39z.8UocLY0lD9d.
!
no aaa new-model
no network-clock-participate slot 1
no network-clock-participate wic 0
ip cef
!
!
!
!
!
!
!
!
!
!
!
interface ATM0/0
no ip address
ip nat outside
no atm ilmi-keepalive
dsl operating-mode auto
hold-queue 224 in
!
interface ATM0/0.1 point-to-point
no ip redirects
pvc 0/35
oam-pvc manage
dialer pool-member 1
protocol ppp dialer
!
!
interface FastEthernet0/0
ip address 192.168.xx7.5 255.255.255.0
no ip redirects
no ip proxy-arp
ip nat inside
speed 100
full-duplex
!
interface ATM0/1
no ip address
ip nat outside
no atm ilmi-keepalive
dsl operating-mode auto
!
interface ATM0/1.1 point-to-point
pvc 0/35
oam-pvc manage
dialer pool-member 1
protocol ppp dialer
!
!
interface Dialer0
ip address 207.xxx.xx.xx0 255.255.255.0
ip mtu 1492
ip nat outside
encapsulation ppp
ip tcp adjust-mss 1452
dialer pool 1
ppp authentication pap callin
ppp chap hostname xxxxxx
ppp chap password 0 xxxxx
ppp pap sent-username xxxxx password 0 xxxx
!
interface Dialer1
ip address 207.xxx.xx.xx1 255.255.255.0
ip mtu 1492
ip nat outside
encapsulation ppp
dialer pool 1
ppp authentication pap callin
ppp chap hostname xxxxx
ppp chap password 0 xxxxx
ppp pap sent-username xxxxxx password 0 xxxxx
!
ip default-gateway 192.168.xx7.3
no ip forward-protocol nd
ip route 0.0.0.0 0.0.0.0 Dialer1
ip route 0.0.0.0 0.0.0.0 Dialer0
ip route 192.168.xx8.0 255.255.255.0 192.168.107.3
ip route 192.168.xx9.0 255.255.255.0 192.168.107.3
ip route 192.168.xx0.0 255.255.255.0 192.168.107.3
ip route 192.168.xx1.0 255.255.255.0 192.168.107.3
ip route 192.168.xx2.0 255.255.255.0 192.168.107.3
ip route 192.168.xx3.0 255.255.255.0 192.168.107.3
!
ip http server
no ip http secure-server
ip nat inside source list 1 interface Dialer0 overload
!
access-list 1 permit 192.168.xx7.0 0.0.0.255
!
control-plane
!
!
line con 0
line aux 0
line vty 0 4
password wgndp
login
!
!
end
 
Upvote 0 Downvote
Can you ping Google from the router? Also, post a sh int

Burt
 
Upvote 0 Downvote
no can't ping google from router. Here is sh int

DSLrouter#sh int
ATM0/0 is up, line protocol is up
Hardware is DSLSAR (with Alcatel ADSL Module)
MTU 4470 bytes, sub MTU 4470, BW 256 Kbit, DLY 2000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ATM, loopback not set
Encapsulation(s): AAL5 AAL2, PVC mode
23 maximum active VCs, 256 VCs per VP, 1 current VCCs
VC Auto Creation Disabled.
VC idle disconnect time: 300 seconds
Last input never, output 00:00:00, output hang never
Last clearing of "show interface" counters never
Input queue: 0/224/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: Per VC Queueing
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
34054 packets input, 881636 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
21442 packets output, 563656 bytes, 0 underruns
3 output errors, 0 collisions, 0 interface resets
0 unknown protocol drops
0 output buffer failures, 0 output buffers swapped out
ATM0/0.1 is up, line protocol is up
Hardware is DSLSAR (with Alcatel ADSL Module)
MTU 4470 bytes, BW 256 Kbit, DLY 2000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ATM
28474 packets input, 569480 bytes
10570 packets output, 211400 bytes
5571 OAM cells input, 5572 OAM cells output
AAL5 CRC errors : 0
AAL5 SAR Timeouts : 0
AAL5 Oversized SDUs : 0
Last clearing of "show interface" counters never
FastEthernet0/0 is up, line protocol is up
Hardware is AmdFE, address is 000c.851c.ad60 (bia 000c.851c.ad60)
Internet address is 192.168.xx7.5/24
MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive set (10 sec)
Full-duplex, 100Mb/s, 100BaseTX/FX
ARP type: ARPA, ARP Timeout 04:00:00
Last input 00:00:00, output 00:00:00, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/40 (size/max)
5 minute input rate 9000 bits/sec, 10 packets/sec
5 minute output rate 3000 bits/sec, 3 packets/sec
1829618 packets input, 199670855 bytes
Received 1314142 broadcasts, 0 runts, 0 giants, 0 throttles
1 input errors, 1 CRC, 0 frame, 0 overrun, 0 ignored
0 watchdog
0 input packets with dribble condition detected
530198 packets output, 65874209 bytes, 0 underruns
0 output errors, 0 collisions, 3 interface resets
41908 unknown protocol drops
0 babbles, 0 late collision, 0 deferred
287 lost carrier, 0 no carrier
0 output buffer failures, 0 output buffers swapped out
ATM0/1 is up, line protocol is up
Hardware is DSLSAR (with Alcatel ADSL Module)
MTU 4470 bytes, sub MTU 4470, BW 640 Kbit, DLY 800 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ATM, loopback not set
Encapsulation(s): AAL5 AAL2, PVC mode
23 maximum active VCs, 256 VCs per VP, 1 current VCCs
VC Auto Creation Disabled.
VC idle disconnect time: 300 seconds
Last input never, output 00:00:01, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 3
Queueing strategy: Per VC Queueing
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
4000 packets input, 132921 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
3969 packets output, 116760 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 unknown protocol drops
0 output buffer failures, 0 output buffers swapped out
ATM0/1.1 is up, line protocol is up
Hardware is DSLSAR (with Alcatel ADSL Module)
MTU 4470 bytes, BW 640 Kbit, DLY 800 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ATM
2666 packets input, 58217 bytes
2634 packets output, 52680 bytes
1334 OAM cells input, 1335 OAM cells output
AAL5 CRC errors : 0
AAL5 SAR Timeouts : 0
AAL5 Oversized SDUs : 0
Last clearing of "show interface" counters never
NVI0 is up, line protocol is up
Hardware is NVI
Interface is unnumbered. Using address of NVI0 (0.0.0.0)
MTU 1514 bytes, BW 10000000 Kbit, DLY 0 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation UNKNOWN, loopback not set
Last input never, output never, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
0 packets output, 0 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 unknown protocol drops
0 output buffer failures, 0 output buffers swapped out
Virtual-Access1 is up, line protocol is up
Hardware is Virtual Access interface
MTU 1500 bytes, BW 100000 Kbit, DLY 100000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation PPP, LCP Closed
Base PPPoATM vaccess
Vaccess status 0x44, loopback not set
DTR is pulsed for 5 seconds on reset
Last input never, output never, output hang never
Last clearing of "show interface" counters 22:38:29
Input queue: 0/4096/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/40 (size/max)
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
0 packets output, 0 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 unknown protocol drops
0 output buffer failures, 0 output buffers swapped out
0 carrier transitions
Virtual-Access2 is up, line protocol is down
Hardware is Virtual Access interface
MTU 1500 bytes, BW 256 Kbit, DLY 20000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation PPP, LCP Listen
PPPoATM vaccess, cloned from Dialer0
Vaccess status 0x44
Bound to ATM0/0.1 VCD: 4, VPI: 0, VCI: 35, loopback not set
Keepalive set (10 sec)
Last input never, output never, output hang never
Last clearing of "show interface" counters 15:15:18
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/40 (size/max)
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
10573 packets output, 126876 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 unknown protocol drops
0 output buffer failures, 0 output buffers swapped out
0 carrier transitions
Virtual-Access3 is up, line protocol is down
Hardware is Virtual Access interface
MTU 1500 bytes, BW 640 Kbit, DLY 20000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation PPP, LCP REQsent
PPPoATM vaccess, cloned from Dialer0
Vaccess status 0x44
Bound to ATM0/1.1 VCD: 4, VPI: 0, VCI: 35, loopback not set
Keepalive set (10 sec)
DTR is pulsed for 5 seconds on reset
Last input never, output never, output hang never
Last clearing of "show interface" counters 03:57:28
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/40 (size/max)
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
2636 packets output, 31632 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 unknown protocol drops
0 output buffer failures, 0 output buffers swapped out
0 carrier transitions
Dialer0 is up, line protocol is up (spoofing)
Hardware is Unknown
Internet address is 207.xxx.xx.xx0/24
MTU 1500 bytes, BW 56 Kbit, DLY 20000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation PPP, loopback not set
Keepalive set (10 sec)
DTR is pulsed for 1 seconds on reset
Last input never, output never, output hang never
Last clearing of "show interface" counters 1d00h
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: weighted fair
Output queue: 0/1000/64/0 (size/max total/threshold/drops)
Conversations 0/0/16 (active/max active/max total)
Reserved Conversations 0/0 (allocated/max allocated)
Available Bandwidth 42 kilobits/sec
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
0 packets input, 0 bytes
0 packets output, 0 bytes
Dialer1 is up (spoofing), line protocol is up (spoofing)
Hardware is Unknown
Internet address is 207.xxx.xx.xx1/24
MTU 1500 bytes, BW 56 Kbit, DLY 20000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation PPP, loopback not set
Keepalive set (10 sec)
DTR is pulsed for 1 seconds on reset
Last input never, output never, output hang never
Last clearing of "show interface" counters 1d23h
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: weighted fair
Output queue: 0/1000/64/0 (size/max total/threshold/drops)
Conversations 0/0/16 (active/max active/max total)
Reserved Conversations 0/0 (allocated/max allocated)
Available Bandwidth 42 kilobits/sec
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
0 packets input, 0 bytes
0 packets output, 0 bytes
 
Upvote 0 Downvote
Virtual-Access1 is up, line protocol is up
Hardware is Virtual Access interface
MTU 1500 bytes, BW 100000 Kbit, DLY 100000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation PPP, LCP Closed

This is an indication of a bad username/password. Do a debug ppp negot and debug ppp authen and then do a shut/no shut on di0 and di1, and post the results...

Burt
 
Upvote 0 Downvote
here are the results. Thanks

DSLrouter(config)#int dialer0
DSLrouter(config-if)#no shut
DSLrouter(config-if)#
*Mar 3 02:16:49.324: %LINK-3-UPDOWN: Interface Virtual-Access2, changed state t
o up
*Mar 3 02:16:49.324: %LINK-3-UPDOWN: Interface Virtual-Access3, changed state t
o up
*Mar 3 02:16:49.328: Vi2 PPP: Using dialer call direction
*Mar 3 02:16:49.328: Vi2 PPP: Treating connection as a callout
*Mar 3 02:16:49.328: Vi2 PPP: Session handle[FB000010] Session id[10]
*Mar 3 02:16:49.328: Vi2 PPP: Phase is ESTABLISHING, Active Open
*Mar 3 02:16:49.328: Vi2 PPP: Authorization required
*Mar 3 02:16:49.328: Vi2 PPP: No remote authentication for call-out
*Mar 3 02:16:49.328: Vi2 LCP: O CONFREQ [Closed] id 12 len 10
*Mar 3 02:16:49.328: Vi2 LCP: MagicNumber 0x174F2140 (0x0506174F2140)
*Mar 3 02:16:49.328: Vi3 PPP: Using dialer call direction
*Mar 3 02:16:49.328: Vi3 PPP: Treating connection as a callout
*Mar 3 02:16:49.328: Vi3 PPP: Session handle[DE000011] Session id[11]
*Mar 3 02:16:49.328: Vi3 PPP: Phase is ESTABLISHING, Active Open
*Mar 3 02:16:49.332: Vi3 PPP: Authorization required
*Mar 3 02:16:49.332: Vi3 PPP: No remote authentication for call-out
*Mar 3 02:16:49.332: Vi3 LCP: O CONFREQ [Closed] id 8 len 10
*Mar 3 02:16:49.332: Vi3 LCP: MagicNumber 0x174F2145 (0x0506174F2145)
*Mar 3 02:16:51.315: Vi2 LCP: Timeout: State REQsent
*Mar 3 02:16:51.315: Vi2 LCP: O CONFREQ [REQsent] id 13 len 10
*Mar 3 02:16:51.315: Vi2 LCP: MagicNumber 0x174F2140 (0x0506174F2140)
*Mar 3 02:16:51.315: Vi3 LCP: Timeout: State REQsent
*Mar 3 02:16:51.315: Vi3 LCP: O CONFREQ [REQsent] id 9 len 10
*Mar 3 02:16:51.315: Vi3 LCP: MagicNumber 0x174F2145 (0x0506174F2145)
*Mar 3 02:16:51.319: %LINK-3-UPDOWN: Interface Dialer0, changed state to up
*Mar 3 02:16:53.331: Vi2 LCP: Timeout: State REQsent
*Mar 3 02:16:53.331: Vi2 LCP: O CONFREQ [REQsent] id 14 len 10
*Mar 3 02:16:53.331: Vi2 LCP: MagicNumber 0x174F2140 (0x0506174F2140)
*Mar 3 02:16:53.331: Vi3 LCP: Timeout: State REQsent
*Mar 3 02:16:53.331: Vi3 LCP: O CONFREQ [REQsent] id 10 len 10
*Mar 3 02:16:53.331: Vi3 LCP: MagicNumber 0x174F2145 (0x0506174F2145)
*Mar 3 02:16:55.346: Vi2 LCP: Timeout: State REQsent
*Mar 3 02:16:55.346: Vi2 LCP: O CONFREQ [REQsent] id 15 len 10
*Mar 3 02:16:55.346: Vi2 LCP: MagicNumber 0x174F2140 (0x0506174F2140)
*Mar 3 02:16:55.346: Vi3 LCP: Timeout: State REQsent
*Mar 3 02:16:55.346: Vi3 LCP: O CONFREQ [REQsent] id 11 len 10
*Mar 3 02:16:55.346: Vi3 LCP: MagicNumber 0x174F2145 (0x0506174F2145)
*Mar 3 02:16:57.365: Vi2 LCP: Timeout: State REQsent
*Mar 3 02:16:57.365: Vi2 LCP: O CONFREQ [REQsent] id 16 len 10
*Mar 3 02:16:57.365: Vi2 LCP: MagicNumber 0x174F2140 (0x0506174F2140)
*Mar 3 02:16:57.365: Vi3 LCP: Timeout: State REQsent
*Mar 3 02:16:57.365: Vi3 LCP: O CONFREQ [REQsent] id 12 len 10
*Mar 3 02:16:57.365: Vi3 LCP: MagicNumber 0x174F2145 (0x0506174F2145)
*Mar 3 02:16:59.381: Vi2 LCP: Timeout: State REQsent
*Mar 3 02:16:59.381: Vi2 LCP: O CONFREQ [REQsent] id 17 len 10
*Mar 3 02:16:59.381: Vi2 LCP: MagicNumber 0x174F2140 (0x0506174F2140)
*Mar 3 02:16:59.381: Vi3 LCP: Timeout: State REQsent
*Mar 3 02:16:59.381: Vi3 LCP: O CONFREQ [REQsent] id 13 len 10
*Mar 3 02:16:59.381: Vi3 LCP: MagicNumber 0x174F2145 (0x0506174F2145)
*Mar 3 02:17:01.396: Vi2 LCP: Timeout: State REQsent
*Mar 3 02:17:01.396: Vi2 LCP: O CONFREQ [REQsent] id 18 len 10
*Mar 3 02:17:01.396: Vi2 LCP: MagicNumber 0x174F2140 (0x0506174F2140)
*Mar 3 02:17:01.396: Vi3 LCP: Timeout: State REQsent
*Mar 3 02:17:01.396: Vi3 LCP: O CONFREQ [REQsent] id 14 len 10
*Mar 3 02:17:01.396: Vi3 LCP: MagicNumber 0x174F2145 (0x0506174F2145)
*Mar 3 02:17:03.411: Vi2 LCP: Timeout: State REQsent
*Mar 3 02:17:03.411: Vi2 LCP: O CONFREQ [REQsent] id 19 len 10
*Mar 3 02:17:03.411: Vi2 LCP: MagicNumber 0x174F2140 (0x0506174F2140)
*Mar 3 02:17:03.411: Vi3 LCP: Timeout: State REQsent
*Mar 3 02:17:03.411: Vi3 LCP: O CONFREQ [REQsent] id 15 len 10
*Mar 3 02:17:03.411: Vi3 LCP: MagicNumber 0x174F2145 (0x0506174F2145)
*Mar 3 02:17:05.426: Vi2 LCP: Timeout: State REQsent
*Mar 3 02:17:05.426: Vi2 LCP: O CONFREQ [REQsent] id 20 len 10
*Mar 3 02:17:05.426: Vi2 LCP: MagicNumber 0x174F2140 (0x0506174F2140)
*Mar 3 02:17:05.426: Vi3 LCP: Timeout: State REQsent
*Mar 3 02:17:05.426: Vi3 LCP: O CONFREQ [REQsent] id 16 len 10
*Mar 3 02:17:05.426: Vi3 LCP: MagicNumber 0x174F2145 (0x0506174F2145)sh
*Mar 3 02:17:07.442: Vi2 LCP: Timeout: State REQsent
*Mar 3 02:17:07.442: Vi2 LCP: O CONFREQ [REQsent] id 21 len 10
*Mar 3 02:17:07.442: Vi2 LCP: MagicNumber 0x174F2140 (0x0506174F2140)
*Mar 3 02:17:07.442: Vi3 LCP: Timeout: State REQsent
*Mar 3 02:17:07.442: Vi3 LCP: O CONFREQ [REQsent] id 17 len 10
*Mar 3 02:17:07.442: Vi3 LCP: MagicNumber 0x174F2145 (0x0506174F2145)
DSLrouter(config-if)#
*Mar 3 02:17:09.461: Vi2 LCP: Timeout: State REQsent
*Mar 3 02:17:09.461: Vi2 LCP: State is Listen
*Mar 3 02:17:09.461: Vi3 LCP: Timeout: State REQsent
*Mar 3 02:17:09.461: Vi3 LCP: State is Listen
*Mar 3 02:17:09.597: Di0 DDR: dialer shutdown complete
*Mar 3 02:17:09.617: %LINK-5-CHANGED: Interface Virtual-Access2, changed state
to administratively down
*Mar 3 02:17:09.621: %LINK-5-CHANGED: Interface Virtual-Access3, changed state
to administratively down
*Mar 3 02:17:09.621: Vi2 PPP: Sending Acct Event[Down] id[20]
*Mar 3 02:17:09.621: Vi2 LCP: State is Closed
*Mar 3 02:17:09.621: Vi2 PPP: Phase is DOWN
*Mar 3 02:17:09.625: Vi3 PPP: Sending Acct Event[Down] id[21]
*Mar 3 02:17:09.625: Vi3 LCP: State is Closed
*Mar 3 02:17:09.625: Vi3 PPP: Phase is DOWN
*Mar 3 02:17:11.601: %LINK-5-CHANGED: Interface Dialer0, changed state to admin
istratively downexit
DSLrouter(config)#int dialer1
DSLrouter(config-if)#no sh
DSLrouter(config-if)#
*Mar 3 02:17:36.225: %LINK-3-UPDOWN: Interface Dialer1, changed state to up
 
Upvote 0 Downvote
Status
Not open for further replies.

Similar threads

efuenteso
  • Locked
  • Question Question
Etherchannel Load-Balancing issue
Replies
1
Views
241
burtsbees
burtsbees
Scubaguy3
  • Locked
  • Question Question
Load Balance two Internet links on two routers
Replies
1
Views
294
imbadatthis
imbadatthis
cflcrosland
  • Locked
  • Question Question
Load Balancing, CEF, VPN, Route-Maps
Replies
0
Views
153
cflcrosland
cflcrosland
billyj1900
  • Locked
  • Question Question
load balancing
Replies
9
Views
372
dgrizzard
dgrizzard
skk391
  • Locked
  • Question Question
Load Balancing .. using 3 ATM cards... Is it possible?
Replies
0
Views
135
skk391
skk391

Part and Inventory Search

Sponsor

Back
Top