Search results for query: *

hi, does anyone know how to connect to tn566 audix MFB? i have a null modem cable but i also need a ED1E434-11 G311 M-M rs232 cable according to the docs but what is this? i can maybe make one if i know the pin outs. any ideas? thanks guys

swapped psu swapped IP406v1 3.0.577 to IP403 3.0.577 1x DT16 exp port 1 1x DT16 exp port 2 1x Ph8 exp port3 all 5.0.577. swapped TDM interconnect cables. swapped expansion unit. all extensions on expansion module are cut off system does not...

hi i have issue with users on 2nd expansion port being cut-off (DT16) i have swapped the DT16 module but problem remains. the system itself does not reboot but seems to be problem with TDM interconnect.i have run monitor and can see the following (below) at the time it occurs, any ideas...

IF I AM WORKING ON 3.1 I WILL USE 3.1 DOCS AND THESE STATE THAT 412 LAN PORTS ARE FULL DUPLEX ALTHOUGH THIS HAS INDEED BEEN CORRECTED IN 3.2 DOCS. INCIDENTALLY 3.2 406V2 LAN PORTS ARE DOCUMENTED AS FULL DUPLEX. PERHAPS THER ARE PLANS FOR 412V2 WITH FULL DUPLEX PORTS??

THANKS SO IS FIXED AT HALF. THEY NEED TO GET THESE DOCS CORRECTED

MINE ALSO BUT DOCUMENTATION (BELOW) ALSO STATES TO THE CONTRARY? IS THIS CONFIGURABLE? "LAN RJ45 socket. These ports form a managed layer 3 Ethernet switch. The ports are full-duplex 10/100Mbps auto-sensing, MDI crossover ports."

CAN ANYONE TELL ME WHETHER THESE PORTS ARE FULL OR HALF DUPLEX AS THE TECH BULLETIN(BELOW) STATES HALF BUT INSTALLATION DOCS STATE FULL DUPLEX 10/100 AUTO SENSING?? "The Fast Ethernet ports on the IP Office are set to half duplex. Avaya mandates that when the IP Office 412 is plugged into a...

what possibilties do you see??

does anyone know if i can route DDI to destination to set hunt group out of service as it does not seem to work when programmed thus:- line group ID 0 ICR eg 123456789 destination *81 where *81 represents the following short code entry code *81 tel number 500(hunt group extension) feature set...

thanks Kargo but the files were originally written to flash mem card from 3.1.65 admin cd when it was installed using TFTP and IPO Manager? also sizbut i cannot see status of memory card as i do not have a card reader although this takes messages for only one hunt group and was emptied two days...

Hi, call in to hunt group route to group voicemail and plays prompt but no message in mailbox. sys mon trace display the following:- LVMailFlashMan::ServiceAppendQueue: SOFTWARE ERROR - Deletion of Message from Flash Management List failed: File 31002 any ideas??

my fault. security settings issue within 3.2 services. thanks anyway disturbedone

yes have you successfully performed 3.2 to 3.2 upgrade before?

cannot seem to do this? have changed working directory to 3.1bin folder but all units failed to upgrade each time i use upgrade wizard. any ideas?

cannot get the above to work. want handset option rather than headset

i am havi g problwms integrating G3Si cm1 with 8411D terminals although this works with callmaster 6 OK does anyone know if 8411D is supported with CM1 as client will not use headset and prefers previous set up as per PC console??

When installing anti-virus software with BCMSVu, set the histdb.mdb file for exclusion from the anti-virus service. You may need to consult your anti-virus documentation for this. Remote users are unable to gain access to historical reports because the database is locked by the anti-virus...

so for i will need conf channel, vm port and data channel? how many of each exist respectively on IP406 Ip412? if you can direct me to appropriate docs i would appreciate it thanks guys

i have existing site 1 with cisco router/ cisco firewall and IP406 and site 2 with same but no IP406. Existing vpn over Public Internet via DSL. apart from the set up of the IP Hardphones themselves at site 2 what would need to be configured on IP406 at site 2? (v2.0) I am hearing from...

what are respective max call recordable channels on v2.0 IP403, 406, 412? As far as I am aware 406= 20 but with 24 data channels I am not sure. Similarly 412 has 100 data channels? Will i need a conference port for each call being recorded and does the call recording affect mailbox operation/...