Search results for query: *

Congrats!! ---------------------- Cisco Forum | News http://www.ciscohq.com

Rather than reinvent the wheel :) Some basic ACL info http://www.ciscohq.com/FAQs/Cisco-FAQs/Basic-How-to-Cisco-Access-Lists-ACLs-.html ---------------------- Cisco Forum | News http://www.ciscohq.com

Sounds like HSRP may be what you are looking for. ---------------------- Cisco Forum | News http://www.ciscohq.com

I would discourage the use of telnet for this purpose, telnet traffic is sent in clear text. The prefered method is SSH. ---------------------- Cisco Forum | News http://www.ciscohq.com

Hi, for future reference I believe the 1721 is not at EOL and is listed as a suggest replacement for the 1720. ---------------------- Cisco Forum | News http://www.ciscohq.com

As the previous poster stated. If you can show your current configs, general network layout and a current sh ip route we can maybe offer some insight. Thanks ---------------------- Cisco Forum | News http://www.ciscohq.com

Have you tried to enable logging and viewing logged messages? Syslog would also fit the bill, setup a syslog server. I think Kiwi has a free one. ---------------------- Cisco Forum | News http://www.ciscohq.com

I wonder if this could be a 12.4 IOS bug? marcmongeau are you running the same IOS version? ---------------------- Cisco Forum | News http://www.ciscohq.com

I've also used "non-Cisco brand name" memory before and have never had a issue with it. I think I have even RMA'd a router before with non brand memory and didn't have a issue, but of course your mileage may vary. ---------------------- Cisco Forum | News http://www.ciscohq.com

Martin is correct, a default route ip route 0.0.0.0 0.0.0.0 ser0 should be added. ---------------------- Cisco Forum | News http://www.ciscohq.com

Hi, If you have had a T1 down for just 1 day I would say you are fortunate. I have had T's down for more than a day before. I can't really give you to much advice on Lucent equipment, I would recommend switching over to all Cisco equipment if money is no issue. Using Cisco, you have a couple...

Check Kiwi Cat tools out, it sounds like what you are looking for. http://www.kiwisyslog.com/cattools2.htm ---------------------- http://www.ciscohq.com

Hi, Some more information is needed to answer your question. Can you post a general network layout and current configs? ---------------------- http://www.ciscohq.com

Hi jss817 You have 3 options. 1- Check and see if your current IOS version has a security advisory. Cisco will offer you a free upgrade. I don't know what version that they will give you but it is worth a look. 2- Check EBay. I believe you can find a legal version there. 3- Puchase from...

Don't forget to copy run start!!! :) Cisco's website is a great resource but can be tough to navigate through the 11 million webpages. Forums are a great source of information in my opinion. Good luck! ---------------------- http://www.ciscohq.com

A little read about default gateway's and statics, might help you out. http://www.ciscohq.com/FAQs/Cisco-FAQs/Cisco-IP-Default---Gateway.html

As for ideal equipment, it is hard to give you an answer without more information as to what your network is and what you will be doing with it. For balancing 2 T1's...... http://www.ciscohq.com/FAQs/Cisco-FAQs/Cisco---How-to-T1-Load-Balancing-DS1s-.html ----------------------...

Good point Nicole, I'm not sure if pigsback was trying to hotswap these cards or not. ---------------------- http://www.ciscohq.com

A couple options 1) An IOS version conflict. Maybe another IOS version/feature set? Worth a try. 2) Your card is bad? Have you seen this yet? http://www.cisco.com/en/US/products/hw/routers/ps274/products_tech_note09186a00800b6e0f.shtml ---------------------- http://www.ciscohq.com

As jpm121 stated it is a possible routing issue among other possiblites. If you have some config's can you post them? ---------------------- http://www.ciscohq.com