Search results for query: *

What version of the IOS are you using? It could be a bug. I had a switch that could not stop rebooting...... TechTryer <-- (:All we can do is do our Best:) -->

You can do it from a CAT3550, that is creating increments of 8Kbps For the 2950 switch, the only available QOS limiting possible is multiples of 1M from 1M-100M with burst sizes or 4K - 64K 128K-512K is only for gigabit ports. rate limiting is not supported on the CAT3550 but you can do that...

OK thank you mate! I would really appreciate that. Look forward to seeing the configs Cheers TechTryer <-- (:All we can do is do our Best:) -->

Very funny about the english remark.......:( You have to understand that it is my 3rd language, and not 1st. I can see that you are a big cisco fan. I did set it to 5Mbps but i still get around 2.6Mbps If you can help me get this working, i would really appreciate it. My switch is a 2950T-24...

This is exactly what i need to do. Were you able to make it work. I configured exactly as what was stated in the QOS mannual. However, when i tested it with 4Mbps, all it allows is 2.6Mbps. Cisco is full of crap TechTryer <-- (:All we can do is do our Best:) -->

I have a Cisco 2651XM router with a Channelized T1/E1 card for my ISDN PRI. I need to figure out how to accept incoming calls from BRI and assign them to a specific dialer profile. The reason being i would like each site with a BRI to have a specific Dialer Map. Do u guys have any idea how to go...

Greetings Cisco Gurus I am a bit of a newbie to the Cisco world so i wuld greatly appreciate any help you may offer. We recently installed new 2950T-24 switches into our LAN so that we could do VLans. However, we still have some older 2950-24 switches, (Ones without Gigabit Uplinks) used...

When we changed the switches over, we didn't touch the servers, so i am not sure why this would be the problem. It worked fine with the old settings when we were using the old netgear ones. Cheers TechTryer <-- (:All we can do is do our Best:) -->

Thanks mate for your reply, We have set all the ports to 100MB at full duplex. The IOS we arre running is 12.1(13)EA1a which was the version that the switch was shipped with. Will check on the CCO for any caveats. Cheers TechTryer <-- (:All we can do is do our Best:) -->

Thanks for that, i will try that. Is there any documentation on that feature on the cisco webiste? I have searched but have had no luck. Cheers TechTryer <-- (:All we can do is do our Best:) -->

Thanks mate for the help But i have already configured the relay agent. I was wondering if the switch itself could act as a DHCP SERVER Can it? Cheers TechTryer <-- (:All we can do is do our Best:) -->

I have just recently acquired a Cisco Catalyst 3550 series switch for our LAN backbone. From the IOS CLI. i could see that the switch not only acted as a DHCP relay agent but also a DHCP server. Would anybody be kind enough to show me resourses on how to configure this switch as a DHCP server...

Our config is like so: - Cisco 3550 - does interVlan Routing Cisco 2950T-24 - has Vlans assigned to particular ports Now we have two racks (servers inside) that are both on Vlan 2. The two uplink ports have been assigned to VLAN2. Now when we do backups (rack 1 to rack 2), the through put...

I typed in this command u mentioned but the following error kept coming up from the console. unable to sent UDP on port 161? What is that all about? Cheers TechTryer <-- (:All we can do is do our Best:) -->

Hey Andy If you do have a sample config, i wouldn't mind taking a look. Just to give me an idea of how its done. Thanks mate for all this help, its great. Cheers TechTryer <-- (:All we can do is do our Best:) -->

Any suggestions anybody? TechTryer <-- (:All we can do is do our Best:) -->

Any sugestions anybody? TechTryer <-- (:All we can do is do our Best:) -->

Greetings Andy, thanks for your offer, it's much appraciated. I read on the MRTG website about how to setup a router with snmp enabled to have MRTG monitor traffic on each of it's link. However, it uses IP address to define each link. How would u do that on a cisco switch like Catalyst 2950...

Greetings I am a newbbie to snmp but i was told that a graphing utility called MRTG could be used to determine the traffic through any of the cisco switches. I would really appreciate some help or referels to websites that would be able to setup my switches to have SNMP enables and them setup...

Greetings Andy, Thank you for your contribution, much appreciated. However, is that using the two 2950T-24 switch with the two GigaEthernet ports on the switch. So that config on each switches G0/1 port and using a crossover cable? I tried everything with the two switches, stacking the...