Search results for query: *

Guys, I did the CatOS to IOS conversion using the Cisco doc and it all went fine. I would advise using a Flash Card or PCMCIA card to load the new image rather than TFTP or FTP. Also make sure you change where to boot your image from i.e. bootvar. Regards Paul Paul Kilcoyne B eng. CCNA

Well you'd put an IP address on a Port if you wanted to have a layer 3 connection to another Switch or Router. Regards Paul Paul Kilcoyne B eng. CCNA

Vipergg, thanks for the input. I found out that I should have been looking at disk0: instead of slot0: Weird as all documentation mentions slot0: cheers Paul Paul Kilcoyne B eng. CCNA

Hi, got another issue, I've a 64Mb PCMCIA flash card and copied an IOS image onto it via my PC. I then placed it into the slot0 of my 6509 Sup II but when I do a "dir slot0:" or sh slot0:" I get an error. I've tried formatting the Card using the "format slot0:" command but it fails when I reach...

Hi, can anyone advise the advantage of going from CatOS to Native IOS on a 6509 Sup II? Also is there a dependable procedure? Is it risky? Is there a back out procedure if it goes wrong? Any tips are most appreciated. Regards Paul Paul Kilcoyne B eng. CCNA

Cisco 4507R is a very good L3 Switch. Paul Kilcoyne B eng. CCNA

Hi, I have a 4400se Switch and various other 3coms Switches I'm auditing. I need to find where on each Switch certain Servers are connecting i.e. on what port/ interface they are connected. I can easily do this with a cisco using; sh ip arp xx.xx.xx.xx where xx.xx.xx.xx is the IP address of...

Hi, I'm doing up network diagrams. I'm using the connector buttom on the standard toolbar to represent cables connecting devices. Once I've added the connector I double click on it to add some text. But the test is always horizontal, I'd like it to be "in line" with the connector. I remember...

DW, that seems to make sense. I'll give it a go and let you know how it works. Thanks Paul Paul Kilcoyne B eng. CCNA

Does anyone know how I can have users in different vlans on the same switch assigned to different subnets via Ciscos dhcp Server configuration? I assume I'd have 2 dhcp pools, one for each subnet but how do I get them to link to a certain vlan??? Please help!!!! Paul Paul Kilcoyne B eng. CCNA

Guys, I'm configuring up a 3560 switch with two Vlans. I'd like to use the DHCP feature on the Switch so as to assign an ip address to a user depending on the vlan their connected into. Is this possible? I've got DHCP working in a flat lan using the "ip dhcp pool" command but it assigns the...

Guys, we're having issues on our Network. I did a sniff of the LAN and captured 256Mb worth of data. I can see alot of TCP frame retransmissions. Is there a way to set up a filter so that all that is displayed are the retransmitted TCP frames? Any help is greatly appreciated. Thanks Paul...

Andy, thanks for that it clears alot up in my mind. Anyway what I did was; 1. delete disk0: "old IOS image" 2. copied the new ios to disk0: copy ftp disk0: "new IOS image" etc. All seemed to go well. 2. Once complete could see from a sh disk0: the new IOS was present. 3. configure...

Guys, you've helped me out before so here goes again; I want to upgrade my IOS on a 6513, the device has two supervisors ( sup720 ), each having one flash card. Whats the best way to do this ? Can anyone give me step by step directions ( with commands ) also I'd like to have the old IOS stored...

Hi Guys, I'm from Ireland and trying to understand how ADSL works here. It seems it uses ATM and PPPoE, can someone explain how they inter-relate or point me in the right direction? Thanks Paul Paul Kilcoyne B eng. CCNA

Thanks for eveyone's help...its all working again :-) Paul Kilcoyne B eng. CCNA

jneiberger, what is SmartNET? It sounds important. Thanks Paul Paul Kilcoyne B eng. CCNA

Phew....... O.K. got her up by typing; Rommon>boot bootflash: s72033-jk9sv-mz.122-17d.SXB6.bin then when I got into enable mode went into conf t; config>boot config bootflash:s72033-jk9sv-mz.122-17d.SXB6.bin so now its up on one Supervisor, do I have to do the same with the other...

Bukweet, I tried that and here's what happened; rommon 2 > dir bootflash: File size Checksum File name 43549768 bytes (0x2988448) 0x57be7762 s72033-jk9sv-mz.122-17d.SXB6.bin rommon 3 > boot s72033-jk9sv-mz.122-17d.SXB6.bin Loading image, please wait ... Invalid...

Guys, I'm in a bit of a panic. Was trying to erase the config on my 6513 by typing; erase startup config but now the Switch is in ROMMON mode and I dont know how to get it back...!!! Please help........ Thanks Paul Paul Kilcoyne B eng. CCNA