Search results for query: *

update: firstly, the writing on the vcc conns. is so small that i failed to note that they read; 1 & 2, so that was sorted. hooked everything up and hey presto! i have two more usb2 front panel options. they don't care whether i use 1.1 flash drive or 2. tested a driver file transfer (30meg)with...

franklin97355...front panel connectors for usb/firewire/mic/phones are all in one totally sealed piece of sturdy plastic! inaccessible. micker377...sorry, probably confused you with description. i have 8 single connectors for the board marked as above. there is no vcc0 or vcc1...is this...

micker377...this sounds encouraging; i'll settle for 1.1. i appear to have less connectors than usb2 however. this is what the manual says for the board: pin 1; vreg_fp_usbpwro front panel usb power - 2; vreg_fp_usbpwro front panel usb power - 3; usb_fp_po- usb port 0 negative signal...

hi good folks! just posted this one on "cabling" but brike advises that i'd be better here.. i have just been given a nice little case with usb1 on the front panel. however, the m/board i have fitted has only usb2 including the additional m/board connector. any way i can use usb2 to connect the...

thanx bkrike, i shall post as you suggest in harware.

hi cabling geniuses! i admit to zero knowledge on pin-outs (but i can lift heavy weights :). i have just acquired a relatively old case with front usb1.cables for motherboard header. however, the m/board has usb2 only. is there any way that the two are compatible to permit me to use the front...

hi folks! just have time to pop back and say thanks to all contributers. had a lot of stuff to sort through. been playing with 'administrator' permissions etc. made a mess and had to re-normalize my pc (don't ask!) to LINNEY: i had had no success until trying your suggestion on settings; "Hide...

thanx mbusa, i'll drag it to quick launch. danjwalker, i don't think that i have a viral prob, just a corrupt link somewhere. however, i'll run all additional anti-stuff to make sure. thanx for your input. still puzzled as to origin/meaning of error though.

thanx guys for the input, have just measured an 80mm fan and found the "80" to be the frame size..wasn't looking for that (duh!)...jiminks is right on..92 it is thanx again all

hi franklin, no manual. i am really asking what the accepted method of measuring case fans is, before i go buy one (complete with grill) thanks

hi folks! i use notepad frequently in xp and have never had any probs. with it. suddenly, using it through the start menu, i get the following message: "the c:\WINDOWS\system32\csrss.exe application cannot be run in win32 mode" i have googled the prob. but only found a possibility of corruption...

hi folks! i have bought a nice little midi case; second user, knowing that i need to buy and fit a top-mounted case fan. problem is that i do not know the dimensions of the case fan i need!! an 80mm fan is too small; at which point i realised that i don't know how these fans are measured...

...sorted! many thanks Garebo.

hi folks. just a quicky. i have always looked at the SMBUS options in the bios as archaic in modern rigs! but the fact is i know nothing about it and can't find an explanation that means anything to me (duh!) can i assume that it has been superceded by advanced control options and ignore it? or...

...i had already downloaded the redistributable version of the program, saved it to disk and transferred it to the new computer. the problem on execution was the question posed by the upgrade on opening it, ie. it wanted to know where i wanted to put it. i didn't know. however, since we last...

hi bcastner, quick reply! this is the files i downloaded from cnet...what is .msi? i remember downloading a small file to desktop when upgrading from m/soft, but i don't have this is this instance...what can i do about it?

hi folks! i need to put dx9.0c on a new system which i haven't connected to the net. downloaded it from cnet. it is asking me where i want to put it! i am using a usb2 flash drive for the transfer. could s.o. tell me the directory that i need to enter for the upgrade? thanks.

....back again; and read bcastner's possible causes. you can put me down for the mismatched ram. i added a third stick of hynix memory, cl3 (it said on the label) and started getting the errors. i was not immediately suspicious because i was testing an old ti4400 in this old p3 rig as it had...

hi folks! i too have been receiving exactly same errror messages; with the exception of bcp1/bcp3 addresses; just to throw something in, i have no burner mounted; only a cdrom. interesting about the psu; mine is only a cheapy. other info i have gathered thus far suggests possible memory stick...