Search results for query: *

Hello, Is there someone willing that could walk me through configuring a BRI phone using a TN 556D circuit pack. The terminal that will be used is a 8510T. This will be my first attempt to get this working. I have no problems with programming the phone itself. I'm having problems on the PBX...

Ed, Thats what i currently have on 2 stations and it works great. The recorder is located is the same building. We are going to install a new centralized recorder that will cover our police, fire house etc. Which are in seperate buildings. The problem with using a handset patch is that there...

Looks like i was premature in saying everything is working OK. Here is my set-up. Please bare with me while i try to describe what im trying to accomplish. I am in the process of installing a digital voice recorder to record emergency phone calls at our fire house. (I.E. 911) This ext shows...

Thanks for all the input. I was able to park, retrieve a parked call with no problem. The only thing that changed for me was that when you retrieved the parked call that is a ABRDG-APPR you dial the FAC then the ABRDG-APPR ext. regardless on what digital set you park it on. But when i made it a...

Hello, I have a customer that wants to be able to "Call Park" one of there personal C.O. lines that appear on there digital sets Can this be done? I know theirs no problem if it was an ABRDG-APPR. But haven't been successful with a personal CO config. I have a G3SI running release...

Hello, I will be upgrading my LD trunk to a PRI. Is this a fairly easy process in regards to my pbx provisioning? I have a G3SI running Multivantage 1.1.3 I know i need to replace my DS1 pack with a TN464. I also need to do the following: "Cha ds1 xxxxx" as the old circuit AMI/SF...

Due to the design ( it was never built to two site up at once) i not able to call my other location. I have a a/b box that i switch between my other site. I did check my route pattern. It is provisioned like you mentioned. I'm at a loss here. I hate to have the tanberg vendor show up to find...

I agree. However it doesn't meet DOD spec's

I failed to mention the encrption device sits between the ascend and the tanberg. This device is currently bypassed to eliminate it from the equation. Regards, Greg

I need to be able to encrpt my video and data before it goes out onto the PSTN.

Mike, Are you talking about the segment between the ascend and the tanberg? Thats not a BRI connection. It uses the RS-449 connection (I could be wrong on the RS protocol) off the ascend and then connect's to a a matching set of eastern researh video line drivers. Which in turn connect to the...

Mike, I'm running Multivantage 1.1.3 Regards, Greg

Hello, I recently had a VTC system installed by a contractor. We are having difficulty terminating and initiating video calls. I have a G3si running Rls 1.1.3. The configuration is as follows: A PRI from the pbx to a Ascend imux 3000 provisioned for 6 channels the balance are OOS. From the...

hello, When provisioning a ISDN PRI, Can someone tell me what the A,B,C represent in the DS1 protcal field? 5ESS, AT&T custom etc. Thanks, Greg

The number in question is 1-888-728-3455. The routing table is set up to route these numbers correctly. I can complete other 888 calls that route out the same trunk with no problems. It just a couple that will not terminate. I know this numbers are in-service as i can complete these calls via...

Mike, I recording is as follows: " Your call did not go through, Please try you call again, 052T" Greg

Hello, I have a Definity G3SI that was just upgraded from R8.2 R11.1.3 Since that up grade i am experiencing call rejection o a hand full of 800 numbers. Here is the event the PBX kicked back: denial event 1164: ISDN call reject D2=CV D1=0xcc D2=0x310310 Any help would be greatly...

I need to replace a old drop and insert CSU with a new 120A4 ICSU. The circuit involved is a DS1/PRI on my definity. We are running release 11.1.3! I'm sure this doesn't matter, but the DS1 pack is a TN 464F Can anyone out there tell me the proper sequence (include commands) to disable a...

We had a Avaya tech show up today. They determined that the DPDM was faulty. Because we are running R3.3, Avaya will not support the trouble. Does anyone out there know where i can get a new or used MPDM? I have a PBX and voice mail upgrade in the works, But i didn't want to rush because of an...

Ok i found where to busy out the VM side. I busied and release per you directions and had no luck. The MPDM act's like it's tring to pass data. When i release the link it lights up and looks normal. But of course this doesn't last only 20 sec. or so. I guess i'll need to break out my credit...