Search results for query: *

We have several 403's at our remote sites and an S8700 at our central site, I would like to setup a conference bridge and am not sure which system to do that on. Our IPOffices are using integrated Audix so I don't have VM lite or PRO, and I didn't know about conference center. All I want to be...

Yes, the OLD.IP.RANGE/29 and NEW.IP.RANGE/28 are totally different IP ranges, however they are both from the same provider so they are both configured to use the WAN router serial interface IP address.

One other question, since the new IP range uses the same router IP on the WAN side do I need to make any route changes on my WAN router?

I currently have a public IP range from my ISP of /29, we have run out of addresses so I requested more and they gave me a second range with /28, the new range is configured to use the same router IP as the gateway but I am not 100% what I need to change on my PIX so it will handle that new...

Telemarv - Thanks for the info, I had a feeling it was 6 by something since there were the 6 line ports on the left side, but wasn't sure if software or system version dictated how many of them worked. Phtek - Do you know where I can find a description of the pinouts for the 66 block? Thanks all!

OK, bad example, what about the other keys, like PAGE, PICKUP, TRANSFER, LAST NUMBER, DIAL etc...

Can anyone direct me to a good reference resource to use for programming buttons, I have several M7310 phones that I need to add another line to, and I want to move the INTERCOM and other keys around. Thanks.

I recently purchased a bulk of network and phone equipment at auction from a failed business in the area, included in this was a Nortel NT5B01 phone system. Doing a google search revealed this is a 6x16 KSU system, however I also noticed the same part number also claimed it to be a 6x8 and 4x8...

I am trying to add a 5th phone line to my CICS, I know the line is good as I have punched it down on my old line 4 and get tone, I have added it to the system as LINE025 and programmed it on a phone however when I press the line button I get dead air and then a message stating "NOT IN SERVICE"...

I have a quick question about the basic conferencing bridging - We have several IPO and I would like to setup one as a conference bridge, can we do that if we are using centralized Intuity voicemail? If so can someone point me toward some setup docs, I can't seem to find any. Thanks.

Hi, I have a PIX 515E that I inherited and haven't really touched much since it was running happily, however we are now doing disaster planning and I am looking into a failover unit. I noticed the VPN software was enabled on the PIX and was wondering if someone could point me in the right...

Hi, dumb question - My ISP recently gave us a second range of IP addresses (our current range has a 29 bit mask) with a 28 bit mask, how would I go about adding this range to the outside interface on my PIX so I can create additional translation rules to my internal hosts. Thanks.

Building configuration... : Saved : PIX Version 6.1(1) nameif ethernet0 outside security0 nameif ethernet1 inside security100 hostname Firewall domain-name microsoft.com fixup protocol ftp 21 fixup protocol http 80 fixup protocol h323 1720 fixup protocol rsh 514 fixup protocol rtsp 554 fixup...

I have the route in my L3, I think the nat0 config might be just the thing, where would I find that? Is that the HOSTS/NETWORKS tab in PDM?

Users can ping the internet address of the PIX without a problem, they can't ping the router but that is the same for all the hosts, I know the route is correct on the PIX because I can ping any host on any VLAN from the PIX. I figured it has to be a setting somewhere but can't seem to find it.

I do understand VLANs, I have my L3 doing all the routing between my VLANs now, which works fine since my users are on 3 different VLANs and my servers on a 4th, and I have a route statement on my PIX for the entire 10. class A which summarizes my entire network but still no luck...

We have just moved from a single flat network to a segmented network with multiple vlans, previously everyone on the segment was able to access the internet without needing to configure a proxy server however now it seems that no machines, except those in the same VLAN as my PIX, can access the...

We currently have our Internet access via a 512K PVC on our frame and I need to add additional bandwidth. Instead of using the same frame provider I have gone to a second vendor to add some redundancy, I assume since I have a free slot in my PIX I can add another ethernet interface but I am...

pmesjar - so if I create a management vlan (say vlan99) and I assign a separate vlan address for vlan99 on each of my switches (all in the same subnet of course), but all my switchports are assigned to a different vlan, how can the concept of a management vlan apply unless I have a host in that...

vipergg - I have a L3 switch at my core, connected to multiple L2 switches, I setup VTP on the L3 and the VTP domain has successfully propogated to the L2 switches. I haven't limited any vlans on my trunks between the core and the edge switches, and I can ping the L2 switches when I telnet into...