Search results for query: *

Thanks minue, I try to taking out "igmp join-group 236.10.10.1" and voila I got 100% data...with no loss but why this effected to my data....it just join group of IGMP ...and I just want to receive from this grop only. could you explain to me about this?..thanks regards, vincent

I do test using cisco 2621 router ios: c2600-is-mz.121-27b.bin, 256M memory. CPU utilisation is about 4% I just sending this data only and no other data goes to the router should I do any QoS? I do sending multicast data (text data) for about 70 entry per second, bandwidth needed is about...

Hi.. I got an application broadcasting data by using IP Multicast. by using this configuration below everything work well data_source---switch---IP encapsulator----DVB_Decoder---DVB_encoder---client but by using this configuration below by adding router in between there was data loss...

Thanks Vipergg, I'll try to stack them first, will let u know the result. thanks tor the doc. best regards, cincent

Hi, I Have Cisco 2811 with HWIC-4SW attached in slot 2, It is running well now, I can do Vlans on each port and also do vlans routing on that module, but When I attached the second HWIC-4ESW module on slot 3 it doesn't work, I can configure all the things and I ARP table is also there but I...

its connected to catalys 2970 gigabit switch and some of them connected directly to 7606 gigabit interface (WS-X6148A-GE-TX). already check all speed/duplex setting are match. already try to use cat6 also but the ignored error counter is still increasing maybe amdavad is correct this is cisco...

Dears, I have anomaly detector module and anomaly guard module installed on my 7606 Cisco router, but My detector guard always fail to run ssh command to guard to create dynamic filter anyone can help me to check wheteher any miss cofiguration on the detector/guard module? please advice...

Dears, Thanks for the information, I already got the JDM from local vendor here and I can do manage my switch again, but unfourtunately I can not reboot the switch at that time. Now I can access to the console and also telnet again after I do reboot the switch on the maintenance period. Thanks...

dear rainman I use RJ45 interface using CAT5e Cable (is about 2 meters only) my hardware version is 2.11 as showm below: and I have no problem with my dS3 interface. ################ Cisco 7206VXR (NPE-G2) processor (revision A) with 917504K/65536K bytes of memory. Processor board ID 35231514...

Hi Jeroel, I've try those console setting, but still can not connect to the console, can I access to BS425-48T by using JDM via SNMP? what version of JDM can manage BS425-48T? I will try to use SNMP to access my switch. looking for someoene who has access to download JDM :) Best Regards, Vincent

Hi, I'm using Cisco7206VXR NPE-G2 System image file is "disk2:c7200p-spservicesk9-mz.124-11.T.bin" i found input error on all gigagit port below is show interface gigabit result just after i do clear counter: 5 minute input rate 3968000 bits/sec, 1551 packets/sec 5 minute output rate...

Hi, I got Nortel Baystack 425-48T, I cannot access to the switch via telnet and also via Console, but all the traffic is still working fine, has anyone experience the same problem? I need to reset the switch but I'm afraid this is the firmware issue and will not boot perfectly. anyone can...

dear all, I have problem with console C100. when im connected via serial port n hyperterm, i can see msg from bootloader. but i cant type anything in console. anyone can help me? thanks.

how to set the board to factory default? i didnt see any jumper in this board? when i connect via serial, i didnt see any msg. anyone can help? thanks.

I have this module too, but i need the jumper setting for this modul (J8, J9, J13). Does anyone have documentation for this module?

Dear all, Any one have jumper setting for module 5625 10/100M Base-tx Enet Switch for system 5000?

Help with my passport 2430, its allways restarting. How to solve this? It is Sun, 5/23/2004, 11:01:52 (AM) PP2430 Diagnostics: TARGET pp2430ram: Rev 1.18 Created Fri Dec 8 08:49:04 EST 2000 Memory config: 16MB It is Sun, 5/23/2004, 11:02:05 (AM) Testing CPU Board...

Help..... i have catalyst 4006 sith WS-X4013 module. how to break the password????? i dont have WS-X4232-L3 mdule. need some help... urgent. thanks.