Search results for query: *

Hi, I like to re-direct on a incomming a-number on a BC11 system. What I like to do is connect a specific a-numbers to a specific extension or route. If external number 0123456 calls in to the PBX it will be connected to extension 333. But all other external are routed as usual. Can NUTRI be...

It is possible on TLU75 with a patch if the caller id is of the DTMF type. There was a patch named FR 93912 for BC11.

The pinouts for this serial link can be found in Alex. Look in the: "Extra facilities without commands" "Access Agent" "Installation" "Installation Instruction" I hope this helps you. /MDatHome

Thanks for all help ! /MDatHome

Thanks for all the input so far. The only problem is that there is no way to user fiber but there is cupper cables that can be used. /mdathome

Hello, I have a problem. I need to connect 2 MD110 with ISDN. This is on a railroad where the they like to have there own transmission. If I have a TLU76 (30B+D) there is a limit of the cables stated in Alex: - 180 m if using a 75 ohm coax. cable without repeater. - 260 m if using a 120 ohm...

This is my sugestion to you: - Backup should be done automaticly every day. (DUFQI) - Replace HDU every month. (have at least 3 HDUs to switch with) Store the "not in use" HDUs in a safe. - Do a check every day for alarms and history logs and clean them up after solving the problems...

Hello, I have a 1LIM system with 2 magazines and this takes ~70-80W. Note that you can not place the magazine in as it is wider than 19". /MDatHome

The battery is replaced now but the fault remains. Any more ideas ? /MDatHome

Also make sure that you do not have a firewall that stops the traffic. If it fails to logon, do check with IPEXP if the MD110 think it has register the phone. This is an example with a firewall that gives totaly wrong IP: ipexp:dir=all; IP EXTENSION DATA DIR IP ADDRESS RAS PORT CS...

Hello all, I have got a used A1000 RAID rack and it worked for about 2 days then it stoped to work after a power failure. I have connected to the serial line on the back to see whats happening. It starts but ends with some warnings and then nothing happens. Send <BREAK> for shell access or...

Hello all, I have got a used A1000 RAID rack and it worked for about 2 days then it stoped to work after a power failure. I have connected to the serial line on the back to see whats happening. It starts but ends with some warnings and then nothing happens. Send <BREAK> for shell access or...

To lalrl What sort of problem do you have ?

I had the same problem. This patch forces the NIU to use SCSI ;-) PCASI:UNIT=IOH,CI=SCSI,REV=4-R4A,IA=3E0,RA=3F4,BYTE=0; MOVE.B #2,($39,A6); MOVEA.L ($2C,A6),A4; END; !A; PCACS:UNIT=IOH,CI=SCSI; Y; PCCOS:UNIT=IOH,CI=SCSI; Y;

Hello all, Some one told me that there exist a additional program unit for BC11 that allows some sort of groupcalls to multiple members at the same time. Trunk calls was working too. It was possible to get the mobile phone ringing at the same time as a extension inside the PBX. Is there...

Hi all, Is there anyone here that has samples of &quot;Conflict resolution&quot; methods on Oracle 9i advanced replication ? /MDatHome

Hello, njohn343 Yes it is possible to find out the IPEI if it is not shown on the DECT phone. First start a unit trace on CTLP: <STUNI:UNIT=CTLP,LIM=1; <STTSI:TRI=1; Then try to register the dect in MD110 (unsuccessful)... <STTSE:TRI=1; <STRAP:TRI=1; TRACE IND READ RESULT TRACE...

First of all make sure you have the latest firmware files on the ELU32 board and the IP-Phones. If you change the jitterbuffer size you need to restart the ELU32 board to get it work with the new parameters. The ELU32 sends the priority in ToS and the network must be switched (no hubs) to...

Have you tryed to use DISA to access the actual phone and change the FME ?