Search results for query: *

Some of this is too much to answer in a couple of short paragraphs or a few bullet points. You are actually going to be able to tell someone in a few lines how they are to partition a p690? Obviously, you have never done anything with LPARs. Not that it is terribly complicated, but you cannot...

www.ibm.com/developer

Hello, The SAN is faster then SSA. Go with SAN.

WWWWWWWWWRRRRRRRRRROOOOOOOOOOOONNNNNNNNNNGGGGGGGGG. every one is wrong about schedtune. If you call IBM evey they will tell you not to touch schedtune. System is getting low on memory and that cause context switch. if you reduce % of memory for file pages your system will run f faster...

www.redbooks.ibm.com then search word 64 and aix.

1) add more memory. 2) update AIX code to latest level. 3) install bos.adt.sample then use vmtune to tune memory.

WWWWWWWWHHHHHHHHHHYYYYYYYYYY?. You do not read do you.? At AIX 4.3.3 the kernel is 32 bit only. It does not matter oracle is 64 bit. The kernel is not. Only at AIX 5.1 kernel is 32 bit or 64 bit.

do search on hacmp and redbook on this forum you will find the answer.

Hello, I want to congratulate you on you doing search in this database. Buy the way avadh and aixat are the same and one. Do this steps for me. 1) lsdev -Cc adapter and post the output. 2) why the adapter is either configure as IBM adapter or Emulex adapter. i need to know this. 3) lscfg -vp...

Solution: Since disk io goes to 100. What kind of FC card you have and check with storage tek. Run filemon command when IO is 100% to findout what file is the most active file. The problem will be in either hardware connection. WHY DID YOUR COMPANY BUY SOLUTION FROM STORAGETEK. THE MAIN...

WRONG ANSWER. ONLY AT AIX 5.1 there is option to use either 32 bit or 64 bit kernel. The 64 bit application environment is for any application (for example Oracle) that could use of 64 bit hardware. This question has been asked before on this forum do the search on it and you will find more...

Hello, All the above updates are WRONG. nmon is not IBM software. If you change the memory model and set memory allocation for paging early then it is allocated early - if that is not changed then. Look at vmstat output - if fre column fall below 120 then paging takes place and page from real...

Hello, lslpp -l bos.rte.libc and lslpp -l bos.rte.libpthread. if this at 4.3.3.75 then update to latest level. It will fix the problem you see.

1) check vmstat output when the job dies. look at fre column. 2) having you done memory tuning.

look at www.redbooks.ibm.com then find book on performance read on.

Hello, one option is to take the file from aix to pc then use 3270 emulation software to upload the file to 390 system. The IBM 3270/5250 pcom software will do the file conversion for you.

If bos.mp file set is installed then from software side nothing has to be done. if the system has bos.up fileset and new cpu is added then bos.mp file set has to be installed and linking has to be done.

Hello, if you have a hardware documentation and it does not give reference to conversion of address then it is strange error.

I take offence when one says IBM!=open system. Because IBM does excellent job of testing hardware. When it failes it gives you error message and you can also findout what slot(more then one slot for memory) of the memory slot has bad memory and same goes for any hardware.

Hello, You have taken a wrong step. The diag function is needed. if there is a problem with hardware then you want to run diag -> advance diag -> problem determination -> on the device and if it comes back with SRN service request number you want to call IBM hardware to comeout and fix...