Search results for query: *

Are you sure that the CLI is present and un-restricted? It could be that CLIR has been configured i.e. restricted. Best to do a signal trace and confirm your thoughts.

Thanks John, but my issue really is with the DMS end. I can change the numbering plan and number type by using CTYP in DMI. However the kit tandems in the M1 with ISGF (IN) and goes (OUT) to the DMS with ESGF. The number type from the kit is "UNKNOWN" which the DMS rejects. I can modify it in...

Can anyone help me with connectivity, from a Nortel option 11 PBX to a DMS100 using Qsig (ESGF)? ideally I`d like a DMS guru as I can configure the M1 for different number plan and types but I need the DMS to accept number plan/ type of "Unknown". The DMS service provider doesn`t know the tables...

Hi Q6, Do you know what software level you are at on the MD?? Some of the features are becoming available as an "open standard" ISO/ECMA however I don`t think Transfer has made it yet. Therefore I expect that the Q sig transfer request will go as UUI over Q sig.It looks as if...

Hi, I`m afraid this info is not "freely" available, what you need is BTNR 188 or the NICC equivalent (probably in pdf now) I think it`s section 4 which gives you info on the "string identifiers". and later on for the clear cause codes. There are some useful sites re. DPNSS...

Has anyone experience of programming Qsig features on BC10 MD110 using GFT rather than UUI? (the connection is a Nortel Meridian switch.) One problem seems to be that the MD110 sends a "cmninform" message which the Meridian switch doesn`t understand and returns an IE of "not...

I need to do the same with Nortel (option 11), also name display only works in one direction! Call back request fails with incompatible destination from MD? MD is BC10 so using ISO and GFP, Nortel using ISIG. How can I test CCNR and CCBS on a loopback route on MD?? Can you use Cust 1 and...

Thanks for this, so that makes the Meridian not able to do it or the MD110.I`m told the Realitis does?? time will tell. Thanks again, yes I`ll stick for the time being with DPNSS.

Does name display work over DPNSS network? it works o.k. "on switch" but doesn`t get displayed at far end. Net services are set o.k. Is any special settings needed for Key phones?? DBC213?

Thanks for your info ( we do actually use the ntbk51aa) already on the Option 11 for the NTBK50 PRI card (Qsig). I tried today to configure but the LD17 prompt states tmdi d-channels available 0, in use 0. Guess I`ll have to get back to Nortel to switch them on. Thanks again.

What else do I need to connect an ISDN telephone to the ELU 26 for BRI? Will any NTE do ? or Ericsson specific? Has anyone go the configs? Thanks.

Can anyone help me concerning T1 PRI on an Option 11? We ordered some T1 cards from Nortel and received a NTRB21 (1.5Mb)TMDI card, a NTAK20 (clock controller) and a NTBK51AA daughterboard. The documentation (553-3011-310) seems confusing , what I need to know is whether I now have enough cards...

LCNT (loop number) is another good command, helps you asess what may be wrong. How many clock controllers have you set up? and/or what switch are you talking about?

#31# doesn`t clear the light, I had another code which was cancel ringback, but that didn`t work either. Does anyone know a command to printout what codes do what (cept codes??)

Why does the led on a digital telephone continue to flash after ring back has been set and used? How can the flashing be cleared other than removing and entering "key " command again?

Hi, never played with this T1 stuff,what TL block are you using and hardware? There is a INDDAT statement, d12 set to 0 gives extended superframe and b8zs. Any good???

Route data below, Thanks, JD. <RODDP:DEST=327; EXTERNAL DESTINATION DATA DEST DRN ROU CHO CUST ADC TRC SRT NUMACK PRE 327 70 15000000000250 0 1 0 END <ROCAP:ROU=70; ROUTE...

I`m trying to get full CLI to go across the DPNSS network, i.e own site code and extension number. I have set EXNOPR to be equal to the site code but then only this gets delivered and not the extension number, if I remove it I only get the extension number. Any ideas??? I need it for call...

Sometimes you can`t do changes, you need to out and start again.

Does your question relate to DPNSS (IDA) trunks and calling number or calling name??? I`ve spent a lot of time trying to get &quot;calling name&quot; across a DPNSS link and don`t think it is possible, only on switch or via a isdn/qsig link. If it`s caling number you want it should be straight...