Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

  • Congratulations Mike Lewis on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Search results for query: *

  1. Dave Corey

    Option 61c Call forwarding to external number over IPFlex (SIP)

    Well I changed the opt of CFO to CFF and then it worked. Thanks again for your help
  2. Dave Corey

    Option 61c Call forwarding to external number over IPFlex (SIP)

    This is what I have TYPE RDR_DATA CUST 00 OPT CFO CFRD PVCD CWRD FNAD FDN FNAT FDN FNAL FDN CFTA YES CCFWDN CFN0 4 CFN1 3 CFN2 4 DFN0 4 DFN1 3 DFN2 4 DNDH NO MDID YES NDID YES MWFB YES TRCL 0 CRT0 00 00 00 00 CRT1 00 00 00 00 CRT2 00 00 00 00 CRT3 00 00 00 00 DAY0 DAY1 DAY2...
  3. Dave Corey

    Option 61c Call forwarding to external number over IPFlex (SIP)

    Hello, We recently changed our phone service from (2) T1s to AT&Ts IPFlex solution. I haven't had too many problems with the new service but I have one now. We never had the option enabled on our switch to call forward to an external number due to our previous management as they did not want...
  4. Dave Corey

    Octel 250 - RAID 1 disk failure - need to replace failed drive

    Well, I have successfully replaced the drive. I searched regarding modem connections and found that you needed a wyse50 emulation so I found a version of ZOC7 which had a wyse 60 emulation. I dialed into the modem and followed the procedures that you mentioned above. All went very smooth...
  5. Dave Corey

    Octel 250 - RAID 1 disk failure - need to replace failed drive

    Okay, since Im not entirely familiar with these procedures, when you say about connecting to the modem (which is installed and connected to the system) are you talking about literally dialing up with a laptop and connected to it? If so, I would assume you are using hyperterm to do this. What are...
  6. Dave Corey

    Octel 250 - RAID 1 disk failure - need to replace failed drive

    I have the system back up and running for the moment. I went into the Diagnostics Interactively menu and turned off any system checks for errors so the system did not stop booting due to the disk failure. I still have no way of getting to any of the menus they describe in the manual as far as...
  7. Dave Corey

    Octel 250 - RAID 1 disk failure - need to replace failed drive

    Okay, so now I have a problem. I followed the manual to get into menu 20 offline since none of the options appeared when the system was up and running. I did a shutdown with dump and upon reboot when the system asked for BOOT, I hit control d then U and it said invalid command. My only choices...
  8. Dave Corey

    Octel 250 - RAID 1 disk failure - need to replace failed drive

    Thank you for the info. This will help a lot! I downloaded the service manual and saw how to get into the Menu 20 utilities when booting up. In reading thru the steps that you provided in regards to inserting and removing drives (i.e. steps 2 and 5), do I have to use the de-install drive...
  9. Dave Corey

    Octel 250 - RAID 1 disk failure - need to replace failed drive

    Hello, I am looking for some information / guidance on replacing a failed hard drive. Our Octel 250 unit has 4 drives, 2 for system and 2 for mailboxes. One of the system drives has failed, 01, and I am in need of replacing it. Under the option 12, it says I have 4 disks installed with 3...

Part and Inventory Search

Back
Top