Search results for query: *

Got it... I think I found some Cisco H323 stuff. In ADAN, is see: IFC NI2 ISDN_MCNT 300 Can you provide some insight into these valuse?

I would recommend that you navigate to the Cisco Unified Serviceability page (top right) and look at the SNMP dropdown.

Hello and thank you in advance for your help!! To be fully transparent, all the Cisco voice gateway implementations I've worked on have been MGCP with PRI NI-2 circuits and maybe a few DMS-100 PRI's. I just discovered that we need to migrate our two PRI's terminating on a Nortel Option 81 in...

I found a Cisco article that states Cisco MGCP does not support NFAS. I need to configure the gateway as H323.... have you any guides or scripts on how to do this? (configure a Cisco ISR 2921 as H323 voice gateway?

Thanks KCFLHRC! This doc is very helpful. The only question is now if Cisco will support this NFAS PRI group in an MGCP gateway as this is what we have. The doc mentions: "int_number - A value assigned by the service provider and used to uniquely identify the PRI. The values possible...

I found a CSR that has the following: USOC PRAS3 - PRI Interface 23 B + 1 Backup D (M-M) - D Channel Sharing There is no mention to NFAS and I remember previously working with a Tester and him explaining that these PRI's were not in NFAS. Each of the PRI's show to have their own DCH. Thank you,

... I am assuming that IFC NI-2 means that it is ISND Protocol NI-2 - (just making sure) ... and do you anticipate any impact if i move the Back up to Cisco?

Thanks for the reply! I have the Cisco as ISDN NI-2 which the ADAN lists for both. It prints out that these are set to Clock EXT and User side. I don't know how to see what setting tells me how many digits are being sent to us, though. How can i find this out? Looks like Loop 34 and 50 are...

Hello, We are migrating two ATT (Legacy Pac Bell) PRI's that are currently connected to an Option 81 PBX over to a Cisco ISR 2921 voice gateway using MGCP. The layer 2 and layer 3 come up when they connect to the Cisco gateway card, and Multiple Frames Established is shown in the CLI, but no...

Hello, We are migrating two ATT (Legacy Pac Bell) PRI's that are currently connected to an Option 81 PBX over to a Cisco ISR 2921 voice gateway using MGCP. The layer 2 and layer 3 come up when they connect to the Cisco gateway card, and Multiple Frames Established is shown in the CLI, but no...

Thank you! I think you're onto something... I connected the Cisco to the Option 81's CSU/DSU shelf using an ISDN cross-over cable (as you are suggesting) but I did not use a straight through cable. I'm going to try a straight through and let you know.

Hi all, We are migrating to another telco Carrier. The new Carrier hands-off an NI-2 PRI off a Cisco ISR 2911 with VWIC3-1MFT-T1/E1 cards. We currently have dual PRIs from ATT off a DS3 cabinet - non-NFAS so each PRI has its own DCH. We tried to connect the new PRI hand-off from the Cisco...

Hi all, A simple one - how can a user check call log/call history on their Optipoint set? They've used the check button and navigated through but there were no call logs ???? Thank you!

Thank you!! DIS-ACTDA sure displayed some weird stuff. I REG'd the ACTDA and cleared the issue. Just wondering how that could have happened = is the user capable of typing in a digit sequence to corrupt the ACTDA?

Hi all, There is a digital HiPath 4000 station that forwards directly to voice mail. Line is blinking on the phone. I check ZIEL for forwarding actions such as CFDND and there were none. I actually deleted the DND from the REGEN. Can anyone provide some input? Thank you

Hi all, After a Unix re-install, Telnet is not working. Can you please provide steps on how to enable Telnet on the HiPath 4K V5 Unix/Assistant? Thank you!!

Thank you for the feedback! It was the Controller Card and a power cycle of the shelf corrected the problem.

Hi again! The Configuration Manager app is stuck. In other words, it will not fully load (screenshot attached). HiPathh 4000 V5. Please provide some guidance on how to correct this. Thank...

Hi everyone, How can I run a report to list all phones on a HiPath 4000 V5 system. I need to see all active digital phones, active analog phones, inactive digital phones, inactive analog phones. Thank you!

Yes, they worked fine. As a reference, how do you perform the LOOP test in LD 30? And thank you for your input! A power cycle of the IPE shelf cleared the issue.