Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

  • Congratulations strongm on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Search results for query: *

  1. jjohnston20

    Mitel SX-200 hold recording

    I have a mitel SX-200. right now when we put someone on hold its just silent. I would like to use the built in voicemail to recording a simple message that will repeat so the caller knows the phone is still connected. something simple like Please hold is just fine with me. How do I go about...
  2. jjohnston20

    Mitel SX-200 Putty locked

    I was using Putty to work with my Mitel SX-200 when all the sudden it seemed like the window froze. no key commands would do anything. I tried CTRL-Q to try and bring it back but nothing. Tried CTRL-W like on the SX-2000 but nothing. Enter 10 times with no luck. I closed putty and...
  3. jjohnston20

    Mitel SX-2000 dial tone but can't dial

    ON the ONS card that this phone runs on, I see one of the 16 lights on the front stays light, it never shuts off.
  4. jjohnston20

    Mitel SX-2000 dial tone but can't dial

    It appears to be just this one phone...
  5. jjohnston20

    Mitel SX-2000 dial tone but can't dial

    oh gosh, we just replaced the ONS card... should I try a power cycle of the cabinet?
  6. jjohnston20

    Mitel SX-2000 dial tone but can't dial

    I have a room phone that when I pick it up I hear dial tone. When I start dialing, I hear the beeps from the keys, but the dial tone never goes away, and I can't call any extension or outside. any ideas? I tried a couple different room phones.
  7. jjohnston20

    Mitel SX-200 SMDR port?

    I got it! I used a SMDR program and just did test calls from a room and I got stuff to port into the program, but not my call accounting device, so I think my device is just toast. I found it on a shelf covered in dust... lol that explains why.
  8. jjohnston20

    Mitel SX-200 SMDR port?

    So it looks like nothing is outputting. I hooked up a generic SMDR program and connected to the SX-200 via serial cable, I then made a test call from a room, and no data. I have it set to 1200 8 N 1 is that correct, or should it be 9600?
  9. jjohnston20

    Mitel SX-200 SMDR port?

    In form 34 I have the following EXT NUM = Printer Port PRINTOUT = SMDR PRINTOUT TYPE = Auto Print GUARANTEED - No CDE Data Print is set to a 3 digit extension number. I just want to figure out a way to test and make sure its Sending data out that port. because I hooked it up to that port last...
  10. jjohnston20

    Mitel SX-200 SMDR port?

    Thanks! is there a way to test it, like force the SX-200 to output something? also mine is set to the printer output. would I use a standard serial cable (9pin to 25pin adapter) or would it need to be a null modem?
  11. jjohnston20

    Mitel SX-200 SMDR port?

    How can I find out which port is set as SMDR on my SX-200? I'm trying to connect Call accounting back. someone disconnected it a while back I guess.
  12. jjohnston20

    Mitel SX-200 Room Status change on PMS

    Ok, so my maid in room code is #1 My Clean Occupied "Entry-Code" as shown in PMS is 1 So my code I dial from the room should be #11 I think I get it now. Thanks!! We have been dialing that, but for some reason the room status doesn't change for us... anything Else I need to check?
  13. jjohnston20

    Mitel SX-200 Room Status change on PMS

    No, I'm very new to this. I did more digging over teh weekend on this site, and found the "Maid In Room" you just mentioned. my PMS system is set to *21 for clean occupied. So now that I know the maid in room code, do I dial the maid in room code, followed by the full PMS code? For example...
  14. jjohnston20

    Mitel SX-200 Room Status change on PMS

    I did notice also the below 27 (Room Status Audit) is disabled 33 (Room Status) is disabled 34 (Auto Room Status...) is disabled
  15. jjohnston20

    Mitel SX-200 Room Status change on PMS

    I have a mitel SX-200. I have this hooked up to my Opera PMS system and when guests check in and out the phone system is updated accordingly. I know there is a way to allow housekeepers dial a number in the room to change a room status from dirty to clean etc. But its not working. I did...
  16. jjohnston20

    Convert line from Key System to single line

    Thanks!! that did it. I was going backwards. I was going into that group assignment, and trying to delete the list from there, not from the extensions listed there. lol
  17. jjohnston20

    Convert line from Key System to single line

    Sorry, its a Mitel SX-2000
  18. jjohnston20

    Convert line from Key System to single line

    Thanks! where do I go to delete them?
  19. jjohnston20

    Convert line from Key System to single line

    I have a phone that I want to add to an ACD group. I can't because its set as a Key System type. I went into Multi line set group assignment, but when I change Group type from Key System, to Single Line I get the following message. Cannot Change from group to single line or threshold alert...
  20. jjohnston20

    Auto Dial Phone SX-2000

    We have two phones that have no buttons on them. They were set to dial the operator automatically when picked up. Now they just give a dial tone. Where do I go to set them up again to auto dial the operator when picked up?

Part and Inventory Search

Back
Top