i have a problem in my system, CS1000E Rls. 5.50J, with CPPM hardware, one is working as Call Server and the other as Signaling Server, on my IP Phones, i have a caller's list key, but when i press the key it says, caller's list is empty, but i just called that phone just to check if it will...
when i'm programming for a new ip telephone, i passed on this prompts erl, when i put the value 1 and enter, it gives me error, it says, you have to enable the ERL, what does this mean, any idea where to enable this....the error was SCH1680, it says enable the ERL.....
please help....
if i unregister in the ucm, i can use, user name admin1, then the admin1 password, once it register in the ucm, i have to use the admin, and the admin password...
going back to mgc command line, when i used the user name, pdt2, then the pdt2 password, i was able to login, but when i used the...
i try to go to mgc command line but it's asking me a user name
on user name, i enter admin2, then put my admin2 password, but say's
invalid
what should i enter on user name...
please help....
i have just activated a link between CS1000E Rls. 6.0 and Cisco Router 3825. Call Server and Signaling Server are link via sip trunks.
Created steering codes for Nortel side and created routing points on the NRS side, also created gateway endpoints, domain....
i find this E164 international...
i just upgraded one system from CS1000M chasis Rls. 4.50W to
CS1000E Rls. 7.50Q, everything was working fine, but i have few
questions.
when i try to register in the security domain via ld 117, it gives this error,
SEC102 Element 137.135.128.10 failed to request membership in the security...
how do i assigned prefix on nrs if i have the following scenario from provider....
my vendor assigned for me 02 65352xx and 02 65353xx as my did range
for my rdb programming, my acod is 76....
please help....
jertson
after making changes in the element manager, it says that you have to restart application, after doing so, my d-channel is est now, but still i don't receive a call coming from my provider...
when i check the status of my elan, it does not have an ip,
and says down disable...
the scenario is...
i have a Cs1000E CoRes rls. 6.0 and planning to connect to cisco router via sip, my sip license has 9 ports.
i created a virtual route, created a virtual members, created a virtual loop, virtual zone, and configure nrs.
there is no pri card, my question do i have to configure a d-channel for...
i just upgraded the system from CS1000S rls 4.5 to CS1000E rls 7.50Q everything is working fine, except for name display issue. for ip phone 1120 and 1140 no problem, for ip phone 2002 phase 1 and 2002 phase 2, there was a problem, on some phones name will display, for some it won't display. for...
my system is CS1000M, i have just upgraded from release 4.0 CPPII to 7.50Q CPPIV and installed a signaling server with a new hardware NTDW54 for large system. i make this signaling server as a primary server.
there was another card delivered on site, with the same hardware NTDW54, my question...
i just upgraded the system to CS1000E Rls. 7.50Q from old software OPT 11C system Rls. 22.46, my question is when they are dialing the
system speedcall list, the dialtone appears to be longer like less than 3 seconds, compare to their old software which appear to be shorter like 2 seconds only...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.