Hello.
Customer asked me to share phone book between their two sites and each one has a cluster.
How can I do that?
I tried to share Telephone Directory between two elements from each site.
I received an error message saying that the element is already on other cluster.
Is there a way to...
Today the system is working with a voicemail mailbox receiving and forwarding messages to an e-mail.
When people call the mailbox they need to listen an announce before leaving a message and I need to know if record-a-call is capable to do that like voicemail and if I can do that with only 2...
Thank you, sarond.
Can I set call recording to do the same thing as the embedded vm?
I need to set a mailbox number to receive calls and after the beep people leave messages and then those messages are sent to an e-mail.
Can I do that with call recording with 2 vm licenses?
Thanks for your help.
MXe III
MCD 6.0 SP2
Do you know if there is a time or size limit for the messages received in a mailbox?
I set an embedded voicemail system on a customer system and when we tested how much time a message reach we got a limit of 5min.
Can I set the time limit of the mailbox messages?
I...
Well, if you were right I would not have been able to set a cluster and I did (system 5.0).
I appreciate your politeness.
So the question remains: Do anyone else knows if there is a known issue with IP Networking between system versions 6.0 and 4.2?
It could be a problem with customer firewal...
Hello, gentlemen.
I am trying to set the communication between those different systems versions.
I am receiving "out of service" status from system 6.0 SP3.
I did the same between systems with versions 4.2 SP2 and 4.2 and it worked.
Do you know if there is a known issue to put an IP network...
Ok.
I don't have the access to the Singapore system because it is not part of our support.
But I need to give them info about the cluster so they can set the ip trunk there.
kwbmitel,
So the infos I sent here about the possible configuration are correct?
If they fill the Cluster Elements...
Hi, Dan.
This is the first time I configured a cluster.
I followed the manual.
I don't know what is the best way to make the communication between a cluster and a 3300.
Is there a best practice?
I understand what you say. If we have only two elements in a cluster, there is no need to...
Hello, gentlemen.
I made a cluster with two MXe III. The MCD is 5.0 SP2 PR2. The cluster is working fine.
I need to do an IP trunk between this cluster and a 3300 ICP at Singapore.
I think I need to programm in the Singapore Network Elements form both infos from the clustered MXe's and...
I didn't make it work with your infos, dan.
It worked in the DMZ when we use the 3300 IP address in the ICP-side stream field and the public IP in the set-side stream field.
Anyway we needed to put the MBG to work with redundant internet links through NAT but how to do it when we already...
Thanks again for your help, danramirez.
The DMZ mode is not setting automatically the streamming addresses.
I will try following your tips here.
Best regards. I'll post back with the results.
Rogerio.
I'm writing here again the addresses because moderator edited the post that I asked but he suppressed all numbers not just the numbers in the middle.
MBG used 192.168.26.207 IP address with gateway 192.168.26.254 (firewall DMZ port).
ICP used 192.168.25.204 IP address with gateway...
The default WAN connection is the 187.X.X.3
The secondary is a bakcup WAN and it is used only when the default is down.
We have only the weekends to test the MBG because the impact on customer operations. So when we go again test the MBG, we're going to remove the 2nd WAN connection.
Thanks...
Thank you, Daniel.
We will compare your firewall configuration with ours.
Do you have the configuration of the MBG to send me?
Thanks again for your help.
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.