Hi, It is CS1000M, Cabinet release 5.0.
I have a user having to extensions (SCR) keys on M3904 Telset.
Key 0 SCR 453
Key 1 SCR 543
Now user requested that from Ext 453 he may be able to dial long distances calls along with mobile calls.
From Ext 543 he may be able to dial only local calls, no...
Hi, i have a Nortel ICB working with IP = 188.19.xx.xx, now the data network guys has change all network IPs due to some changes in data center. I have to change the ICB LAN IP so that user may access ICB through there PC`s. How can i change LAN IP of ICB??
Thanks
Hi i have a CS1000E,HA release 5.0 working at a site, MGC card(4-1) of same system is given problem and due to this i have to replace MGC with daughter board also. Mean i have arrange another MGC with daughter board..Can somebody guide What will be the correct procedure to change MGS??
1- I...
Could somebody point a URL or document where i can find difference/advantages and comparison of Avaya LSP solution and Avaya Standalone Solution...I mean comparison of avaya PBX with LSP and standalone option..
Thanks
Hi i have some routers 28xx series...i have few extensions connected with FXS port..these routers are connected with a avaya PBX using E1..The analog extension connected at FXS use avaya PBX PSTN lines for dial out...Can wee restrict some dialing digits on these analog extension connected to FXS...
Hi I have implement a TFD timer (LD 16, TFD=600) on out outgoing root (PRI)....TFD timer is working OK and call gets disconnected at the specified time..However there is no warning tone heard before call disconnect..User are requesting that they should heard a warning tone before call disconnect...
Hi i have a CISCO router tied with a Panasonic pbx through FXS/FXO port. This cisco router is the tied with an Alcatel PBX using E1 connectivity.
Now i wants to remove the Panasonic PBX. Can some body help what hardware/software/firmware required at CISCO router so that i may able to use some IP...
Hi, It is BCM 400, System version 4.0.2.03 with update patches.It is a Call center. I am trying to use silent monitoring feature..
I am following the document for silent monitoring as follows
(all config. has been made according to document)
From two line display set (T7316 skill set)FEATURE...
Any more help regarding "what is the correct format of writing IP/subnet etc/netmask file??...assuming i have IP=198.168.x.x with subnet mask=255.255.255.0 "
thanks
Hi Pal, thanks for replying, Can you or somebody else please help how that happen? i mean there should be something which needs to be check if there is a time difference between both CMS server and CMS supervisor.
Regards
Hi, thanks for replying..Our avaya vendor technician came and resolved the isseue after editing etc/host file...
Can you guys help in understand what is the correct format of writing IP/subnet etc/netmask file??...assuming i have IP=198.168.x.x with subnet mask=255.255.255.0
Hi all..CMS server is showing the time different from the time which shows after supervisor login, how can i resolve the time difference between CMS server and CMS supervisor??
Thanks
Hi, I am struggling with a customer’s CMS link ,it has been set up properly but after turning CMS on, the link does not come up. Given below is the capture of /cms/pbx/acd1/spierr,
14:10:32 [00] TCP OPERATIONAL
14:10:32 [00] PBX WSA
14:10:32 [00] SESS DATAX
14:10:32 [00] PBX RTCS
14:12:32...
Hi, I took a cs1000e from a site. it is of release 5.0 with HA. Its both CPPM has been programmed as SIDE=0 and i am continuously getting error of that on maintenance terminal. How can i assign any one of these CPPM as SIDE=1 without any downtime and without any data loss. Or what will be the...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.