Hello team,
Wondering if you can help to disable feature 85 on a BCM450, we need to avoid people to use it in the phone system.
I have found a section called IP TERMINAL FEATURES nad i have removed the feature 85 but thinking if this only works for IP sets.
Thanks or all your help
Hello team,
I am wondering if you can help with this issue. I have 2 PRIs with Qsig in my nortel PBX rls 5. and i want to activate TRMB to avoid to use 2 channels.I have set it up but is not working any idea, Your help is really appreciated
Thanks :)
Route Conf:
TYPE RDB
CUST 00
ROUT 50...
that's Correct the card number is NT5D12AHE5.
I need to set it up with QSIG so i guess the option i have to set in the route and the DCH is ISGF right?
and the last question is if i have to provide the clock what i need to do? i think i have to set it as NET instead USR right?
Thank you very...
I found the DNUM 3 is available :)
But now i need to set the DIP Switches for the DDP2 card: NTZC72AA. and I am wondering if you have the documentation to set them. yoru help is really appreciate :)
Thanks in advance.
Hi all,
I need to set a new DDP2 card with 2 new DCHs in a Nortel OPC81. But i have a question and i really appreciate your help on this:
- How can i know the DNUMs available to set in my DDP2 card?, my understanding is that i need to check the TTY ports and the DNUMs already assigned to my...
Thanks for your quick response KFCLHRC.
I am thinking to make a backup on the flash card before perform the sysload my steps are:
1- backup data on FlashCard
2- pull out the flash card
3- run the sys on both CPus
4- once everything is up, insert the flash card again
Thanks for your...
Hello team,
I need to apply a SYSLOAD on a Nortel OPC81 CP PIV. But i need to confirm if i have to push the RESET buttons at the same time for 3 seconds and then release them or push both INI buttons at the same time for 3 seconds an then release them.
could you some of you confirm this...
Hello guys,
I was wondering if someone has the manuals for the CS2100 Nortel PBX.
I really appreciate your help if you can tell me where i can get these manuals.
Thanks in advance.
Hello guys,
I was wondering if someone can help me to know the procedure to add trunks h323 in CS1000E rls7.5.
I need h323 access ports, right?
what packages do i need?
What is the procedure to create trunks h323 in the system?
What else do I need?
Thanks in advance.
Hello guys,
I was wondering if someone can help me to know the procedure to add trunks h323 in CS1000E rls7.5.
what packages do i need?
What is the procedure to create trunks h323 in the system?
Thanks in advance.
Hello bdmcdonald. Thanks or your reply., supposing i have licenses. Wht would be next step to check? I am thinking vmg card, a ddp2 Card with dch b t what else, I really appreciate your help :)
Hello guys,
I am trying to configure H323 trunks in my CS1000 (7.5), could you be so kind to let me know what i need to configure 10 h323 trunks?
Thanks guys.
Ok I need the DDP2 with daughter board to create two PRIs with their own DCH.
In resume the last print out is as next:
group 0 has next DNUMs= 0,2,4,5,6,7,12
group 2 has next DNUMs= 2,8,12
so each DNUM has 4 ports (0,1,2,3,4) right?
so if i need to install the DDP and create 2 DCHs in group...
Thanks KFC.
Understood :)
So if i want to add a new DDP2 with daughter board, what DNUM and port I can use if i have the next configuration.
I really appreciate your help
DCH, TTY, Type, GRP, DNUM, PORT, MSDL,
-, 0, QSDI, 0, 0, -, -,
-, 2, QSDI, 0, 2, -, -,
-, 4, QSDI, 0, 4, -, -,
-, 5, QSDI...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.