Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

  • Congratulations Mike Lewis on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Search results for query: *

  • Users: kondalisa
  • Order by date
  1. kondalisa

    CP 600r rlease 5, RJ45 adapter

    Hi dave, thats OK, i m using this RJ45 port now, but there is a Nortel bulletin regarding using of Emphenol to RJ45 adaptor, How do i use this adaptor to connect MGATE card with CP server 600r?? Can somebody point exact connectivity of new RJ45 adaptor in a large system? i mean do i have to...
  2. kondalisa

    CP 600r rlease 5, RJ45 adapter

    Hi,Hi it is CS1000M/81 rls 5.5. I got a new 600r rls 5 server hardware, it has RJ45 connector DS30 on it, i How can i connect server with MGATE card?? in previous hardware there was a 25 pinn D type connector through we connect to MGATE card. I was reading a bulletin regarding CallPilot MPB96...
  3. kondalisa

    Need Advice-CS1000E, Rls 5.5

    Thanks Jack for the tips. Any more tips/advice from other???
  4. kondalisa

    Need Advice-CS1000E, Rls 5.5

    Hi, We are going to install 02 CS1000E Rls 5.5 PBX with 100 IP ext in both PBX with SIP connectivity of both PBX and a callpilot 600r at both site.. I was reading NTP`s of planning and engineering about LAN/SIP tips and it has a lot and i cant summarize especially about LAN requirements/Tips. I...
  5. kondalisa

    BCM200-Lost user ID

    Hi, I bought a used BCM200 from a site, but i dont know its user and password as BCM default user and password not working. How can i reset user/password to default value?? or can i recover it by reinstalling software? I would appreciate if somebody help.
  6. kondalisa

    MSDL 0304 Error

    Hi GH, it is a TELCO PRI and it is use mainly for incoming calls. Any more suggestions??
  7. kondalisa

    MSDL 0304 Error

    Hi, it is CS1000M/81c rls 5.5. I am so oftenly get following MSDL error and PRI gets disabled and after few minutes enabling/disbaling it gets OK MSDL0304 GROUP 0 MSDL 13 (2) 1911 MSDL0304 GROUP 0 MSDL 13 (2) 1926 ERR9032 3 28 14:55:09 6/05/2009 MSDL0304 GROUP 0 MSDL 13 (2) 1932 MSDL0304...
  8. kondalisa

    COS key

    There electronic lock wont work, schedule lock wont work also i think.... Regards
  9. kondalisa

    COS key

    Hi, it is cs1000 rls 4.5. I have a COS key on attendant console through which we changes COS of different extension on daily basis. How could i avoid attendant to change COS of some executive extensions??? I mean i dont wants attendant to change restriction of some 3 or 4 executive extensions...
  10. kondalisa

    Err5142, No route 14 exist

    Hi BI. yes there is one virtual route configure but it route number is different. I will see if TRO is set to YES of this route...What exactly does TRO/VTRO use for??? do i turn off TRO in my route if it is set to yes? wouldnt that effect any thing? Take cares
  11. kondalisa

    Err5142, No route 14 exist

    Hi, It is CS1000/81c, CPPIV, Release 5.5. I am getting the following error after every 4 or 5 minutes ERR5142 00000000 00000014 >err err5142 > ERR5142 x y Required Configurations for TRO-CM to work is missing. Check TRO( Overlay 16) and/or VTRO ( overlay 17) prompts. Where: X is the...
  12. kondalisa

    MICB Time probelm

    Hi John, it is a New ICB card with latest firmware. Are u using CP for conferencing??
  13. kondalisa

    MICB Time probelm

    any help or tip???
  14. kondalisa

    MICB Time probelm

    Hi it is CS1000M,MG release 5.5 and ICB rls 4. PBX patches are updated. Problem is that MICB is not synchronizing it times with PABX, it always gets 20 or 30 minutes ahead after every week. I resetted last week MICB due to time problem which was 28 minutes ahead from PBX and after reset it gots...
  15. kondalisa

    Collaborative Server

    Hi Paresh, can you explain a bit more collaborative server more?? and if you dont mind can you explain briefly when we use END POINT USER and GATEWAY END POINT in NRS?? In what situation. I will appreciate if you do this for us.
  16. kondalisa

    Adding keycodes

    Hi I am adding new keycodes to increase 250 extensions in my existing 11c rls 4 pbx. I got two cabinets and cards from Nortel. Need yours advice how to go with this? i mean can i plugged fiber cable with new 02 cabinets while power is ON? and then insert keycode?? Just need your advice how to...
  17. kondalisa

    IVR-SIP Connectivity

    I manage to register this Voxeo IVr but getting a SIP 503 (I) error, which say not Implemented. The IVR log is given under. Does somebody help in this??? I have defined IVR in Gateway End point entries in NRS. IVR LOG ------- 2009.03.20.17.26.28.671 SIP message(i)...
  18. kondalisa

    CODEC question

    any body else could explain these codes selection config??
  19. kondalisa

    CODEC question

    thanks BI. So it happens automatically? i mean system auto select whic CODEC should be use for all VoIP calls? i mean IP phones/SIP etc...i dont know why all codec are selected and which will be use Thanks
  20. kondalisa

    CODEC question

    Hi, i need some clarification in Codec use, In my element manager Node setup all CODEC options are checked so which CODEC actually will be use for SIP trunks in My NRS? i mean where do we setup which CODEC will be use? and why all CODEC are checked in CODEC option under Node config. It is a...

Part and Inventory Search

Back
Top