Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

  • Congratulations Mike Lewis on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Search results for query: *

  1. jkaval

    How many conferences can a CS1000MG 5.5 have?

    I don't have a 1000e. It's a cs1000MG. An 81C upgraded with 5.5 software. There isn't any SSC card.
  2. jkaval

    How many conferences can a CS1000MG 5.5 have?

    How many conferences can a CS1000MG 5.5 have? I currently have 14 conf/tds cards. I read somewhere that it can have 64 conferences at one time and each conference can have 6 parties. Is that correct?
  3. jkaval

    Call Pilot reset?

    I had one of the managers at our clinic change the password of her call pilot and doesn't know what it is now. It's been a while since I've done this, but from what I remember don't you press F985 then press 1 and enter the resetXXXXXXX?
  4. jkaval

    What is the lease time for IP sets in the DHCP scope

    What is the lease time for IP sets in the DHCP scope. I know it's option 51, but nothing states the lease time.
  5. jkaval

    How long should the lease time be for an IP set

    How long should the lease time be for an IP set in the DHCP scope? I show to have the DHCP scope use option 51, but nothing about a timer.
  6. jkaval

    PRI 226 alarms

    I can look into the QSIG, but the weird thing is we have two programmed the same, but only one has the issue. Could we get those errors from a possible bad cable?
  7. jkaval

    PRI 226 alarms

    Yes. That is the way the vendor for the Call Manager wanted it.
  8. jkaval

    PRI 226 alarms

    PRI0226 Protocol Error: No RESTart ACK message received. Output data: DCH: x DATA: y . Where: x = D-channel number and y = UTN. Contact your technical support group if the problem persists. Severity: Critical What would be causing this? When I reset the DCH it seems to clear up for a couple...
  9. jkaval

    Trouble dialing 866 number

    I did a trace and showed it going out LP 18 (network) and tested a phone with that same result when I traced so...I will look into the fax driver.
  10. jkaval

    Trouble dialing 866 number

    Here is a good one. I have a Right Fax server connected to our CS1000M via T1 so when it dials a number it will use the TIE line to the PBX and dial out from there. I can dial any 866 toll free number, but 1. When I dial that 1 specific number 1866-812-XXXX it shows going out a member on our...
  11. jkaval

    Incoming calls issue

    We had a problem where we couldn't get any incomming calls. Everything looked good on our end. The DCH were up and channels were IDLE, but no calls could come in. I disabled the DCH so it would bounce to the back up then everything worked. I know there was a patch for 3.0, but we're on 4.5 and...
  12. jkaval

    Trouble scheduling a report on CC6

    Does anyone know how to schedule reports to a file. I know when our CC6 was installed a while back it took our vendor a week to figure it out and it wasn't easy. I had to have a folder created on the admin server for each department which our IS security would give each manager access to. Then...
  13. jkaval

    T1 tie question to a Cisco server for RAS

    If the NCOS is 0 for the TIE lines so any NCOS of the incomming trunks should work.
  14. jkaval

    Nortel: Member & Route

    What does the N 040 00 and N 045 00 stand for?
  15. jkaval

    Problem with T1

    This is typically a local CO issue.
  16. jkaval

    T1 tie question to a Cisco server for RAS

    If my NCOS is 0 on the T1 then it should matter what the NCOS is on the incomming trunks correct?
  17. jkaval

    T1 tie question to a Cisco server for RAS

    I have a T1 that is connected to a RAS server for people who still actually dial in for VPN. I can call the number internally and it works fine, but it fails if I call from the outside world. The NCOS is set to 0 on all of the TIE trunks into the RAS and the TGAR is set to 9 so it isn't the same...

Part and Inventory Search

Back
Top