Search results for query: *

Thank

HI Does anyone know if there exists a linux shell command of trace route in IPLU? Thanks & Appreciates. TANHH

Sorry, mistake in steps B, see the following correction: Steps B (corrected) B: is the following steps enough? CLTGE; /*At exactly 24/10/2013 23:59:59), perform the following to end the daylight saving*/ CATII:DATE=2013-10-24,TIME=23-00; CLTGI; Best regards

Dear All At 24/10/2013 midnight (24:00:00), manual CATII is our option to be performed to end the daylight saving to become 24/10/2013 (23:00:00). Our PABX have CIL output operational. Please discuss the correct steps. In my opinion, i'm sure the [b]following way (steps A) will not mess up...

I have discovered this issue in my system since 2 years ago and i have the solution in my way. Well, this problem is very common if there is an IPLU in a consono stackable magazine LBP20. It seemed that the TDM time switch is messed/held up by the IPLU from time to time. CNLIP:DEV=YES,LIM=X...

Telnet with root/root123 works as well. Tested and confirmed.

I would like to know how to set up an EBN with the following requirement. The EBN would be used to house some H.323 IP phones which would in normal state be registered to remote Heardquarter TSW PABX's Gatekeeper (IPLU). When the WAN (over satellite) is down, the EBN senses, react accordingly...

Thanks cpux10. But i suppose the NTP clients (LIM2,LIM3) are able to automatically and consistently poll and synch to the NTP server's time and date with proper settings in the ntp.conf in LIM 1, 2 & 3 respectively. Anyone knows how? Thanks

Let's say i want to set LIM 1 (10.0.0.230) as NTP server, LIM 2 (10.0.0.232) and LIM 3 (10.0.0.234) as NTP clients. LIM 2 and LIM 3 as NTP clients constantly polling to synchronize to LIM1 at 24 hours interval. Can anyone of you post the standard ntpd.conf files' content for LIM 1, 2 & 3...

In addition: What are the precaution and extra necessary steps to be carried after correcting the system time and date?

Hi Let's say I have installed MXONE TSE 3.2 SP4 multiple lims: NTP server is set to LIM1. In the installation, by mistake the system time and date is wrongly set. How do i correct the system time and date (without reinstallation if possible)? In alex...

Thanks whosrdaddy. 1. How can i make full use if the SSH in trouble shooting (monitor, diagnose, checking jitter value etc)? Is there any manual over the commands available? 2. In Alex: ::Connection to the debug port is done via telnet (port=1500) and to access the Linux shell port 23 is used...

I have upgraded from P1C10 --> R1F --> R2K using the guideline from whosrdaddy. After upgraded to R2K, the login using admin/Ericsson over SSH no longer successful. I guees the login/password is different for application firmware R2K. Does anyone know the new login/password over SSH for...

When the PCM links had had unforeseen problem and even after the links' recovery, it seems that the alarm 278 on CLOP still spans over multiple Lims but the Call Billing System however still able to receive the delayed and new call data but in a very very slow manner over the IP network. (also...

Try set D1 of ADC to 0, ie ADC=000520001000025110000111101.

System: Aastra/Ericsson TSW SP6 With Aastra Dect system SARI number, we can derive the SARI PARK. A user brings in a DECT phone which he has accidentally deleted the registration from the phoneset. And unfortunately he never cared what extension number of his dect phone(yeah, we have such...

The valid ISDN signalling in the case of sending Inband Busy Tone at Incoming call is depicted below: 1. PABX sends Progress indicator No 8 (Inband information available) in PROGRESS MESSAGE to indicate PABX has inband tone. 2. Next PABX send DISCONNECT, Timer T305 started. 3. Timer T305 will...

System: BC12 SP11 standard APS. Traffic case: MD110' extension XXXX is busy. External VoiceMail system makes a call to this extension XXXX via ISDN PRI (ISO QSIG). What I want to achieve: MD110 is suppose to provide Inband busy tone to the incoming call from the external voicemail system...