Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

  • Congratulations strongm on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Search results for query: *

  1. yeahbutno

    MiVB 9.0 Upgrade Issue

    FYI This was taken from an upgrade to v9.0SP2 on a Cxi-II. There is a section where the licencing failed as it was disconencted from the network, therefore I licenced it offline for the time being as I had done that initially! LOG VIEW BELOW continued after the backup section (I have altered...
  2. yeahbutno

    MiVB 9.0 Upgrade Issue

    Disable your Firewall completely on your connecting PC and connect straight to the front of the controller. That section literally takes less than 2 minutes. I upgraded a few from a Windows 10 and Windows 7 machine! On a physical controller its normally around 1.5Hours (depending on the size of...
  3. yeahbutno

    Windows 10 with CXi

    crich01 I've been looking for this for bloody ages! This works on Windows 10 as well! Thanks.
  4. yeahbutno

    Hard Drive replacement on MXe-III with Sata Raid

    Maybe this will help on SATA Raid controller information.http://files.engineering.com/getfile.aspx?folder=5f648ad6-4e75-42df-89a6-30d1023a18c9&file=11_5191_00213_MXeIII_SATA_RAID.pdf
  5. yeahbutno

    LS Trunks with Auto-attendant

    What's your Circuit Descriptor settings recomendations from the line provider for disconnection timer/flash timer in circuit descriptor asignment for that LS trunk your using? Suggest, you try to speak to them and let them know the 3300's settings so that the lines disconnect properly from both...
  6. yeahbutno

    3300 "vxworks" not stopping with spacebar

    As above, -Either a Read only rs232 cable therefore unable to transmit the space input or, as Mitelmatt says hit space 3 times then Enter.
  7. yeahbutno

    Inter-tel phones on Mitel 5000 HX Controller

    I know that to STOP that from happening you need to have the following flags set for each extension. Handsfree On/Off (Set to OFF)[Default = ON] Ring Intercom Always On/Off (Set to YES)[Default = NO] Transfer to Connect Allowed (Set to YES)[Default = NO] The above is to definitely STOP it from...
  8. yeahbutno

    Inter-tel phones on Mitel 5000 HX Controller

    Can you define "Voice announce call"? Is it only on certain types of phones?
  9. yeahbutno

    5550 IP console intermittent problem

    Is the console on a static IP address? If not can this done!Also,if it's not static IP then whats you lease time on the DHCP scope?
  10. yeahbutno

    Siemens IP Phone System

    This can DEFINITELY be done on the Mitel system just for clarification+much,much more as with all the latest PBX's out there. Are you thinking of completely migrating to IP since you currently have a 10 Year old system? Then there are many choices for you! As long as your Data network is up to it!
  11. yeahbutno

    Mitel handset volume doesn't save change

    There is an option in the class of service to save the handset volume change! Set this to yes for the specific handset!
  12. yeahbutno

    3300 AX VM Flash doesn't work

    Did you do a FULL install? or an upgrade? As you should do a FULL install if upgrading to version MCD 4.0 and upwards. This will then format your Flash Card to the proper patitions etc
  13. yeahbutno

    Ascom Dect and Mitel

    Have you tried changing the Multiline set key assignment as follows of the DECT extension number in question on key 2 (i.e.Line Type = Multicall,Button Directory Number = it own extension number, Ring Type = ring) within the Multiline Set key assignment form so that the you can retrieve the call...
  14. yeahbutno

    New IP PHone System, 30 Users, Single Location

    If I had the option then without doubt I would go for Mitel,but like KwbMitel said support is of vital importance. So that would more or less confirm my decision if it was between a STRONG LOCAL reseller and that of another SMALLER reseller which has only just STARTED to sell Shoretel...
  15. yeahbutno

    Configuring DHCP on Cisco routers to support Mitel

    See below for info.Note that option 125 is now used for updated firmware for Mitel IP Phones as its vendor specific for Mitel. Cisco Routers can be configured to provide DHCP services on the network. A typical customer configuration would be use the Cisco Router to provide DHCP services in the...
  16. yeahbutno

    voip calling from outlook

    joblack23, Have a look at the Mitel Forum and ask the question there! http://www.tek-tips.com/threadminder.cfm?pid=1329&page=1
  17. yeahbutno

    Mitel Pet Peeves, DCR's, and Wish lists.

    Also, while I'm thinking about it. How about the basic ability of sorting the forms data in ascending order when clicking on the relevent colums e.g. Directory number etc. A little bit like Excel type of thing!
  18. yeahbutno

    Mitel Pet Peeves, DCR's, and Wish lists.

    Thought i would add one to the list.Unless, it's already mentioned or already implemented on the new software versions. Would like an easier programming method of a GROUP mailbox instead of having to use the Name Tag hunt groups design type etc. So that if a certain Hunt group or ring group...
  19. yeahbutno

    sip problem

    Sounds like a QoS issue,have you any IP phones running and if so, you can monitor some by using the Mitel IP Phone Analyzer to see if there are any loss of packets and Jitter on your network which would probably suggest again your QoS.
  20. yeahbutno

    How good is be CCNA?

    I personally think it would be very benifical for you.At least then you get the whole VoIP picture with also the benefit of knowing HOW to set up the WHOLE network,how to troubleshoot the WHOLE network. One thing though it's not an easy course to pass!

Part and Inventory Search

Back
Top