Hello everyone,
I replaced a 403 with a 406 and load the 403 config file in the 406. But for some reason the extensions in office manager do not match the extensions on the patch panel. For example, what's plugged in the 1100 slot shows up as extension 1107. Any ideas on how to configure office...
Hello again everyone,
I have a trunk line coming into the TLU76/1 and this is the fault code: Fault code 274, Digital Trunk, clock Malfunction.
I am assuming that I didn't setup the synchronization, frame, or rate, something having to do with the clock rate or speed for the specified route in...
Hello,
I am in the process of setting up an ISDN (Q.921, ETSI) connection.
Can someone tell me the sequence of commands and boards that play an integral part in setting up an ISDN connection?
Using board TLU 76/1
Here is what I gathered so far.
I. TLU Board configuration
• CNHUI
• ROCAI
•...
when making a call, the call fails and never connect. Below is the printout from Sysmonitor. You can see the call begin, but then it goes down hill from there. I am assuming this line, "11mS PRN: Line 5: Manual: Line Loopback Up" is part of the problem, I never saw Line Loopback Up before, what...
Alright guys, no need to reply. The remedy was to set the calendar ( time and date) of all things, lol. Nice to know the MD 110 is so anal.
Thanks for looking
Hello everyone,
One of the alarms listed is Fault code 106, The one having to do with faulty I/O board. I tried to administer the various test under the FIFTI command but it says my subsystem do not exist, when the system is either SYSDISK1, SYSBUFS11, OR SYSBUFS12,I tried all of these and it...
Hello,
Can someone please tell me how to configure the ethernet port on the NIU2 as a MML port?
Thanks
P.S. I am able to log on to the system now, we created our own V.24 to serial cable, lol.
Here's a printout of what I see:
To run a command as administrator (user "root"), use "sudo <command>".
See "man sudo_root" for details.
cedric@cs-linux:~$ telnet 10.210.15.32
Trying 10.210.15.32...
Connected to 10.210.15.32.
Escape character is '^]'.
>login: sssssSSSSSSS;
Login Rejected...
Also, as I asked before, but no one answered. Do I need another cable to start the MML session? All I have is the ethernet cable, I don't have the V.24 cable is this the problem?
Thanks
pcasi thanks for your suggestion, however you miss understood me I already have the ip address and do not wish to change it. I could login to the NIU2 board, but can't use any of the MML commands. If you reply, please do if you can, can you repy to my other post that talks about the same...
Dave thanks for your reply, I basically open up a unix terminal, and telnet to the NIU2 IP address, then I type SSSSSSS (with no ;) and the default username and password and i get the niux prompt. I also tried SSSSSSSS; and it still didn't work. Do it have to be a combination of lower and upper...
Alright, from my understanding there's two ways to start a MML session; via the IPU board with a special cable, through a cable with a serial port connection via the NIU2 unit, and via the NIU2 ethernet cable and typing in SSSSSSSSS;.
I don't have the IPU board nor the serial cable, so our only...
ok, I FTP into the NIU2 unit and a license file is present.The EIC is correct as well. So, why can't I start a MML session? After I telnet into the NIU2 unit, what do I do to start a MML session?
Thanks
Alright, I am able to telnet (login with username and password) into the NIU2 board. However, I cannot use any of the MML commands. A compact flash card is present on the NIU2 board.
Like cv8devil mentioned, is it because I do not have a license. But, I thought that the factory pre-load the...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.