Thanks @mckinney the issue with that though when you do a retrieve which we all do first thing in the morning it shows the last change was the date of the retrieve. I didn't look at it through command line though. I'll try that
Thanks KCFLHRC Ill try that. The other admin doesnt know the CLI, I've suggested he not use EM but he says its easier. I will do the retrieve and Reconcile though
Hey Gang its been a while since I've posted here.
Has anyone experienced NCOS changes all on their own? We have 2 PBX admins with one being dedicated to our realestate project, that leaves the other admin to do daily MAC work. We have had several reports of users not being able to dial...
Awesome @Wanebo thanks for the verification (and saving me a minute to test that. There are a couple of them like that so I will remove them. The knowledge in this group is fantastic!
@KCFLHRC it shows an ACDN
REQ: prt
TYPE: dnb
CUST 0
DN 7750
DATE
PAGE
DES
DN 7750
TYPE ACDN
@bignose21, If that is the case then I guess there is nothing left to trace. I have not come across this before but I will test your theory. Thanks for the feedback!
We are replacing as well. 10 year old systems all 4 sites are 7.6 the ONLY concern is CP as they are EOL. The "Cloud Hosted" buzz word has reached the heads of the decision makers, and they want no part of a hybrid, so that will be the route we go. It will be a shame to have to disassemble my...
Happy New Year to you all! I have been trying to get detail on extensions, and ACDN for our CS1ks and came across a couple like the one below. I called the ext 7750 and its RNA. There is no NCFW, I don't see any other redirect options. A Call trace (below) shows 7750 being dialed I hear ring but...
Though I've never met him, I felt sad as I read the OP. Ghtrout has provided so much advice here, helped many and didn't even know it.[sadeyes] My thoughts go out to his Family.
FirebirdScrambler, thanks again for taking the time to read and reply. We have only one DAPC table. I have seen this while attempting to troubleshoot this, but wasn't sure of the impact. I will do more digging into the NTP to see how the configuration is making me beat my head against the wall...
While tracking this issue during our SIP testing I found there are other settings in play.
In the route there are two settings that seem to have an affect on this, and I am trying to narrow it down.
TYPE RDB
CUST 00
ROUT 50
DES SIP TRUNK
TKTP TIE
M911P NO
ESN NO
CNVT NO
SAT NO
RCLS EXT
VTRK...
I was the pilot user during interop testing. This should work well, as I think I can just change the ncos for everyone when we go live and leave the rli entry in place for the SPN and NPAs
KCFLHRC, I think that explanation turned the light on for me THANK YOU! I've done routing before but its all been simple outbound. First time I'm trying to restrict many and enable a few.
I need it to be as painless to the user as possible. The ultimate goal is at the end of the 30 pilot ( if successful) to enable all outbound to that route.
Once again I am reaching out the the great minds here. We are implementing SIP to the carrier. I have been working and testing with the carrier for a couple of months doing interop testing. We are ready to start outbound testing with a pilot group.
My question is what would be the best way to...
Thanks for the fast reply FirebirdScrambler, I followed your suggestion and changed the ISPN to yes, and CTYP to NCHG, with the same result.
DMI 3
DMI 3
DEL 0
ISPN YES
CTYP NCHG
The strange thing is that a normal outbound call shows up correctly
DCH 18 OMSG SETUP REF 0000002D CH 18...
I have a strange situation happening I hope someone can help with.
Incoming call to desk phone that is set up to hunt to the user's cell phone
DCH 18 IMSG SETUP REF 000090BC CH 2 1 TOD 11:21:58
PROGRESS: CALL IS NOT END TO END ISDN
CALLING #:313xxxxxxx NUM PLAN: E164/NATIONAL /...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.