Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

  • Congratulations strongm on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Search results for query: *

  1. mikethephoneguy

    CS1000 to IP Office passing CLID on analog trunks

    I was told this is not possible, we have a very frugal customer that wants to use existing trunking to their new IP office.
  2. mikethephoneguy

    no Dial Tone on Analog Cards

    controller card and or ring generator
  3. mikethephoneguy

    CS1000 to Cisco UCM via TDM Voice Gateway

    you need a T1 cross over cable
  4. mikethephoneguy

    PLAR rings IP phone every 10 minutes

    I have an elevator phone connected to a vg224 using PLAR to ring an IP phone. When the elevator phone button is pressed PLAR works the way it is supposed to. However, when the call is cleared the IP phone rings once every 10 minutes.
  5. mikethephoneguy

    L3 Qsig issue on 11c to CME

    RCAP COLP NDI CCBI CCNI PRI DV3I CTI QMWI
  6. mikethephoneguy

    L3 Qsig issue on 11c to CME

    Good Day I am attempting to send CPND from my nortel 11c to a CME but get this error on the 11c when i attempt to make a call: DCH 15 UIPE_OMSG CC_SETUP_REQ REF 0000000F CH 1 23 TOD 7:08:52 CK 5B96FDB9 PROGRESS: ORIGINATING END IS NOT ISDN CALLING #:7152 NUM PLAN: PRIVATE TON: ESN CDP...
  7. mikethephoneguy

    CallPilot to IP Office

    Can we use CallPilot as our VM service off of an Avaya IP Office device? If so how do you do it? links are appreciated! Thanks
  8. mikethephoneguy

    IPO to Nortel 61c intergration

    Is this possible? How would I go about intergrating the two systems? I would like to have the DNs on the IPO set up as a DSC on the Nortel 61c as part of the CDP. Customer has no interest in getting rid of the 61c but wants the two systems to be networked together. I have done many Cisco IP...
  9. mikethephoneguy

    Getting DTI 0012 error

    yes you are correct attempted to enable the loop in LD 60 and got the DTI error there.
  10. mikethephoneguy

    Getting DTI 0012 error

    when i STAT TMDI in LD 96 TMDI X ENBL DITI X OPER PORT 0 DCH 20 DIS PORT 1 when i enable the DCH in 96 and then try to enable the loop in 60 i still get the DTI0012 error.
  11. mikethephoneguy

    Getting DTI 0012 error

    yes i did that and it says its ok
  12. mikethephoneguy

    Getting DTI 0012 error

    yes you are correct attempted to enable the loop in LD 60 and got the DTI error there.
  13. mikethephoneguy

    Getting DTI 0012 error

    option11c running 4.5 attempting to enll tmdi card in LD 60 and i get this error Network/loop x pack does not respond from IOTEST; loop/card x is disabled has anyone seen this before and can expand on what the error code is getting at?
  14. mikethephoneguy

    Changing HLOC on Opt11c

    I have a recycled 11c that I am using for a lab. How do you go about changing the HLOC in LD 90? I am trying to add HLOC 538 42 but keep getting ESN errors saying there is a conflict between the new HLOC and the NXX NPA. Is there any way of adding this new HLOC with out having to reprogram...
  15. mikethephoneguy

    CDP issue

    I have a PRI tie between two opt 11c running 4.5. Site A can dial four digits to site B no problem Site B has to dial the ACOD then the four digits to hit the set at Site A. If i dial from Site B four digits the call goes to the 2250 at Site B.
  16. mikethephoneguy

    TMDI to TMDI connection

    I have two Opt11c's in the shop that we are using for a lab. I am trying to connect the two TMDIs to trunk between the two of them. Right now i am running a T1 straight through cable through an amphenol adaptor to ethernet to the same device on the other Opt11c. No joy yellow alarms on both...
  17. mikethephoneguy

    Can't dial cisco IP phone through auto attendant on nortel 81c

    When dialing our auto attendant number from the PSTN and getting the announcement on call pilot when you dial the IP phone DN(4 digit ) we get the message number is not in service. We have a 3845 set up to the 81c which is then sent through a satellite shot to a 2811 on the far end. Desk sets...
  18. mikethephoneguy

    cant hyperterminal into opt11c

    Thanks for all the help it was a bad SDI port on the 11c cabinet....
  19. mikethephoneguy

    cant hyperterminal into opt11c

    no joy there either....
  20. mikethephoneguy

    cant hyperterminal into opt11c

    trying to hyperterminal into an 11c using port 0 NORTEL null modem through a db 25 to db 9 connector with no joy. any suggestions? thanks in advance Mike

Part and Inventory Search

Back
Top